Showing results: 436 - 450 of 1357 items found.
-
Oxygas 500 -
Teledyne Gas & Flame Detection
The Oxygas 500 compliments the Gascoseeker 500 with a similar performance, measuring % LEL and % volume flammable hydrocarbons, but with the addition of oxygen for either gas/air or gas/nitrogen/air purging. The Oxygas 500 has the following additional features; automated zero during start-up, manually selectable purge mode.The P-500 variant has an additional part per million (ppm) range of methane.The Oxygas 500 is easy to use with very simple training, as the operation of the instrument follows the operation of the purge cycle. The rugged design allows the Oxygas 500 to be used in harsh environments. The instrument is also fully compatible with our range of calibration software and equipment.
-
MX 16 -
Teledyne Gas & Flame Detection
Specially designed for applications in laboratory, storage, small boiler room, and breweries or battery charging rooms, the MX 16 measuring unit prevents the risks of explosion linked to the presence of toxic, anoxic and explosive gases in the ambiant air. Small size, ease of installation and use are the main strengths of the plant. Used with the OLCT 10N O₂ and CO₂ digital sensor series or any other O₂, CO₂, CH₄, GPL and H₂ analog sensor, the MX 16 guarantees you a solution that complies with French and European standards.
-
Syntel -
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
Vidac Solutions
Vidac high pressure testers include a full complement of support equipment. We have integrated the actual high pressure controls, valving and instrumentation into a control system that provides tightly controlled pressure and speed regulation. We also provide a test control system that is fully configurable to run multiple types and sizes of seals and can run any pre-configured test with a level of repeatability that allows test to be started on one rig, finished on another rig and reviewed and reported on a third rig.
-
8716 -
TEGAM Inc.
For measuring atmospheres in hoods, ducts, and vents. A perforated-style shield protects the thermocouple tip from radiated temperature change in order to provide more accurate readings. The 8-1/2" sheath is constructed of 304 stainless steel. The probe is supplied with a 3-ft straight cord.
-
mOByDic5000 -
Ozen Elektronik Inc.
It is a low cost version of our emission test family. This device is provided for LPG/CNG mounting workshop.a windows based PC software allows a fail/pass report.
-
SPECTRA GT30 -
Ametek Power Instruments
The SpectraTM GT30 is easily mounted directly to the turbine case or on a short standoff pipe via a 3/4 inch NPT internal thread. The two-wire, 24 VDC loop-powered solid-state sensor is fully self-contained, therefore it does not require a separate amplifier. AMETEK offers various cabling options depending on the application.
-
Process Sensing Technologies
The PST Dynament nitrous oxide (N2O) Platinum sensors are designed with patented non-dispersive infrared technology and contain all the necessary optics, electronics and firmware to provide a linearized, temperature-compensated output.
-
MOCON, Inc.
Headspace analysis is conducted to ensure that the residual oxygen in a product complies with predefined limits. This is a vital part of the Quality Control of Modified Atmosphere Packaging (MAP) products. For packaged foods and other goods, exceeding these limits increases the risk of growth and proliferation of bacteria or mould, which causes spoilage and results in shorter product shelf-life.
-
Particle Measuring Systems
Supports a complete contamination control solution including cleanroom certification and clean area monitoring, while meeting global requirements for data integrity.
-
-
Model - KM 5540EX -
Kusam Electrical Industries Limited
• CNEX Ex ib IIB T4 GB approved.• High Quality Japanese sensor.• Anti-explosion 3.7V 1500mAH Li-ion battery equipped.• Instant sensor failure indication.• Easily check the status of alarm devices (buzzer, LEDs).• Built-in temperature compensation to provide excellent environment independency.• Audible ticker signal & visual leak size indicator.• Adjustable sensitivity, fast warm-up, low battery indicator.
-
605-00007 -
Parallax Inc.
The CO Gas Sensor is used in gas detection equipment for detecting Carbon Monoxide in home, automotive or industrial settings. When paired with our Gas Sensor Board (#27983) it provides a development system and test platform for CO gas sensor design.
-
Hermann Sewerin GmbH
Here you will find an overview of measuring instruments from Sewerin for gas leak detection. Our portfolio includes gas warning devices, gas leak detectors, gas concentration measuring devices, multigas meters, combination measuring devices, ethane detectors, odorant measuring instruments, biogas measuring devices and a whole lot more...
-
ABB Ltd.
Intelligent Sample Gas Conditioning.