Showing results: 166 - 180 of 1185 items found.
-
LD-7 -
Fuji Tecom Inc.
The LD-7 is the smallest and lightest-weight water leak detector yet it has a very sensitive ground sensor. With the listening rod connected to the ground sensor, listen to the sounds of water-leaks transmitted to faucets, meters and valves.
-
Advanced Energy
Precisely Measure Surface Resistivity, Volume Resistivity, or Resistance to Ground. Advanced Energy's Trek and Monroe resistivity meters offer accurate and repeatable measurements for surface resistivity, volume resistivity, or resistance to the ground.
-
21000 -
S & G Tool Aid Corp
Most widely used automotive circuit tester. Quickly checks all 6 and 12 volt systems. Use with power on. 48" ground wire. Use to locate shorts, grounds and open circuits.
-
61-051 -
IDEAL Industries, Inc.
*Tests for correct wiring, open ground, reverse polarity, open hot, open neutral, hot on neutral, hot and ground reversed with open hot in 3 wire, 120 VAC circuits*Simulates ground fault for testing GFCI*No-slip ergonomic design maximizes comfort*Premium neon lamps prevent false readings*Tough, impact-resistant case*2-year warranty
-
61-035 -
IDEAL Industries, Inc.
*Tests for correct wiring, open ground, reverse polarity, open hot, open neutral, hot on neutral, hot and ground reversed with open hot in 3 wire, 120 VAC circuits*Simulates ground fault for testing GFCIs*No-slip ergonomic design maximizes comfort*Premium neon lamps prevent false readings*Tough, impact-resistant case*2-year warranty
-
106P70-4 -
VECTOR Electronics and Technology, Inc.
Pad-Per-Hole & Overall Ground Plane both Sides.Individual pads with plated-thru holes.0.080” diameter isolated solder pad around each hole on both sides. Etched ground plane surrounds pads on both sides.
-
106P180-4 -
VECTOR Electronics and Technology, Inc.
Pad-Per-Hole & Overall Ground Plane both sides.Individual pads with plated-thru holes. 0.080” diameter isolated solder pad around each hole on both sides. Etched ground plane surrounds pads on both sides
-
Desco Industries, Inc.
Connects to utility ground when plugged inQuick, easy installation and grounding of both wrist straps and table mats.Tests entire circuit - wrist strap, cord and skin contactReliable resistance testActs as common point ground for the worksurface
-
MS 2002 -
Meltronics Systemtech
Distance measuring equipment (DME) is a transponder-based radio navigation technology that measures distance by timing the propagation delay of UHF radio signals. The DME system is composed of a UHF transmitter/receiver (interrogator) in the aircraft and a UHF receiver/transmitter (transponder) on the ground. The aircraft interrogates the ground transponder with a series of pulse-pairs (interrogations) and the ground station replies with an identical sequence of reply pulse-pairs with a precise time delay (typically 50 microseconds). The time difference between interrogation and reply minus the 50 microsecond ground transponder delay is measured by the interrogator's timing circuitry and translated into a distance measurement in nautical miles which is then displayed in the cockpit.
-
RT500 -
Klein Tools, Inc.
Designed to detect the most common wiring problems in standard 120V receptacles.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.Made in USA of U.S. and imported parts.
-
RT600 -
Klein Tools, Inc.
Designed to detect the most common wiring problems in standard 120V receptacles.Also tests GFCI receptacles for proper operation.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.
-
Kyoritsu Electrical Instruments Works, Ltd.
Earth Ground Testing. Most facilities have grounded electrical systems, so that in the event of a lightning strike or utility overvoltage, current will find a safe path to earth. A ground electrode provides the contact between the electrical system and the earth.
-
Hilkar
Grounding Transformers are designed for providing an artificial neutral point for ungrounded three phase power systems. During the line-to-ground faults, grounding transformers provide an easy path to ground faults to limit the fault currents and transient overvoltages.
-
HGT1 -
OMICRON electronics
The HGT1 is a handheld meter to measure ground impedance as well as step and touch voltages. Using the CPC 100 and CP CU1, test currents at variable frequencies can be fed into power cables or overhead lines safely to simulate a ground fault.
-
Hilkar
Neutral Earthing (Grounding) Reactors, which resist current flow through inductive elements, are single phase reactors generally connected between ground and neutral of transformers or generators in order to control single line-to-ground faults at a desired level.