Showing results: 496 - 510 of 1185 items found.
-
INA169 -
SparkFun Electronics
The INA169 is a “high-side current monitor,” which means that you place a resistor (a “shunt resistor”) on the positive power rail and the INA169 measures the voltage drop across that resistor. The INA169 outputs a small current based on the measured voltage drop. If you place a resistor from the output of the INA169 to ground, you can measure the voltage at the output.
-
FC5003 -
Behlman Electronics Inc.
Behlman’s FC5003 is a ruggedly built, COTS frequency converter designed to convert 120/208 VAC, 3-phase, 60 Hz, ground power to 115/200 VAC, 3-phase, 400 Hz, aircraft power. The FC5003 is in a rugged 6U (10.5”H) 19 inch rack mount chassis with an input line cord with plug and an output receptacle.
-
SAS -
AMETEK Programmable Power, Inc.
A spacecraft solar array is subjected to large temperature excursions, varying insolation (the amount of sunlight falling on the array), mechanical changes and aging, which substantially effect both its short and long term performance. In order to test the spacecraft's power environment, a cost-effective solution for ground based testing is to utilize a solar array simulator.
-
AS-AYL-4 WM -
Array Solutions
All materials required for the installation of your receiving loop system, have been included in this kit with the exception of those items listed below under the heading; ‘You will also need. ‘ The specified 8’ x 5/8” copper-clad steel ground rod can be purchased at just about any local hardware store or home center.
-
Botron Inc.
The G.E.M. GroundHog, a Multi-Ground Continuous Monitoring Automation System, is the newest addition to the robust ELITE family of electronics from Botron Company Inc. With a rich feature set never before available, ESD facilities and sensitive component manufacturers can monitor critical grounds in real time in applications ranging from the benchtop to capital equipment.
-
Oxley Group
Typical industrial applications for Oxley Interconnect products include high voltage power supplies, critical computer hard drives, fire safety control equipment, medical and pharmaceutical equipment, oil and gas control systems, power generation and distribution equipment, rail and telecommunications infrastructure. Within aerospace and military markets Oxley products are typically found in aircraft, military vehicles, ground base stations, surface ships and submarines and air and ground communications equipment.
-
COTS -
Astronics Corporation
Our powerful and flexible Ballard Avionics I/O Computers provide the platform for Silo Data recording. These rugged, conduction-cooled, COTS devices combine a powerful computer processor, multi-protocol databus interfaces (MIL-STD-1553, ARINC 429, ARINC 717, ARINC 708), Ethernet, USB, serial, discrete I/O, and other I/O in a small, lightweight package. They deliver outstanding performance on the ground and in the air and are routinely deployed on helicopter, fixed wing, ground mobile, and marine platforms.
-
Dewesoft d.o.o.
Aerospace Testing SolutionsDewesoft offers a variety of solutions for aerospace testing. From standard data recording, structural dynamics, rotating machinery analysis, acoustic testing, to more specific applications like ground station telemetry solutions with full support for ARINC-429 and MIL-STD-1553 buses, PCM telemetry, IRIG 106 - Chapter 10, Ethernet packets, and iNet telemetry.We can provide flexible and robust data acquisition hardware and software that will match your requirement for testing airplanes, helicopters, rockets, satellites in the air, space, or on the ground - proving ground, wind tunnel, vibration shaker or acoustic chamber. Our solutions are being used and trusted by leading aerospace companies on the most demanding projects like NASA, ESA, Space X, Airbus, Boeing, Lockheed Martin, Bombardier, Honeywell to name just a few.
-
27000 -
Matco Tools
Designed for testing electrical circuits and locating shorts, grounds, and open circuits. Electrical circuit tester available for checking 6V and 12V systems. Heavy duty battery clip .
-
DP-16K Series -
PINTEK Electronics
*High Frequency Performance Model*Bandwidth:(-3 dB)**DC~100 MHz (DP-16K)**DC~70 MHz (DP-16KM)**DC~50 MHz (DP-16KL)*2 Range: x100, x1000*Input Impedance:**10 MΩ // 10 pF each side to ground*Over Range Indicate LED*Rise Time: 4 ns
-
ESM-2 -
ROM-Elektronik GmbH
Our new development, ESM-2 electrostatic meter (successor of the tried and tested ESM-1) measures this alternating voltage via a hand-held probe against ground and displays its value digitally and thus easily readable. If the measured voltage exceeds certain values defined in the "Electrobiological standard", it can be reduced to noncritical values by means of targeted, usually simple, measurements.
-
4614-5 -
VECTOR Electronics and Technology, Inc.
3U x 160mm Eurocard size for 96-pin DIN connector. Pad-Per-Hole both sides Voltage and ground buses around board perimeter on both sides Press-fit dual-pole terminal blocks accepts 14-20 AWG wire. Pushbutton release for each pole. Terminal block leads extend 1/8" below bord.Available in 2-pole to 16-pole
-
PlantCare Ltd.
The sensor can remain permanently in the ground and transmits the measured data wirelessly over an IoT net to a server or to a local control center, where they can be used for large area monitoring of soil data (big-data) and also for the automatic control of irrigation and for precisely dosed fertilization. In addition to the total fertilizer content, the sensor can measure the content of nitrogen, potash and the pH value.
-
McLAREN Applied Technologies
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
LabNation
The logic analyser cable plugs in to the AUX port of the SmartScope, providing 8 shielded probe pins for each of the digital inputs, as well as the external trigger input. Each digital probe has its own ground connector and embeds a small passive filter close to the header, allowing for digital probing without signal cross-talk on the cable