Showing results: 991 - 1005 of 1185 items found.
-
Keysight Technologies
Keysight's power limiters provide the best broadband input protection from excess RF power, DC transients and ESD, for a variety of RF and microwave instruments and components. For example, the input circuitry of spectrum analyzers, network analyzers, frequency counters or amplifiers can be protected from unintentional inputs up to 5 watts average power. At even greater power levels, failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
ELMA Electronic, Inc.
Carriers and adapters enable the use of PMCs or XMCs in a PCI based system. Designed to improve your system with additional I/Os. Key control signals on PCI fixed to ground to reduce signal undershoot. Carrier and adapter allowing you customization of your system platform with additional I/O mezzanine boards for your application needs. A 5 V to 3.3 V linear regulator provided. Carriers and adapters are available for different topologies like CompactPCI, CompactPCI Serial, OpenVPX, VME or VME64x.
-
DARE Electronics
DC voltage sensors monitor input voltages ranging from 3 to 500 volts DC with a trip point accuracy of up to 1% in airborne, military and ground power applications. Using internal electronic circuits to detect, monitor and/or sense DC voltage, DARE DC voltage sensors, monitors, and voltage sensing relays can open or close a circuit when a certain pre-set over or under voltage condition exists or the DC voltage falls outside the specified voltage band window.
-
CAEN S.p.A.
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 1.5 kV (A1538D) and 0 ÷ 1/1.3/1.4 kV output voltage (A1515B)- Maximum Current 10 mA, 0.1 or 1/0.1, 3/0.3 mA (dual range boards)- Radiall Multipin, SHV or DB37 connectors- Available with either positive or negative polarity (A1538D and A7038)- Up to 2 nA / 100 pA current set / monitor resolution- Up to 20 mV / 2 mV voltage set / monitor resolution- Very low ripple, down to < 5 mVpp- 3 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx) - Full Floating (A1515B only)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down - TRIP parameter- Current generator operation in overcurrent condition- Specific design for GEM and Vertex detector and dedicatedaccessories (A1515B boards only)
-
75INT2 -
North Atlantic Industries
NAI’s 75INT2 is a 3U cPCI Intel® Core™ i7-based, Single Board Computer (SBC) that can be configured with up to two intelligent function modules and delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.NAI's Intel® Core™ i7 SBCs in the 3U cPCI form factor offer improved processor performance and better security, targeted at military and defense applications such as manned and un-manned air and ground vehicles, and in more sophisticated digital signal processing applications such as intelligence, surveillance, reconnaissance, radar and sonar.
-
69127 -
Klein Tools, Inc.
Device for checking live 6-24V, AC or DC circuits.Tests for shorts in automotive and truck electrical systems, motor field coils, radio and low-voltage circuits, ground circuit of all lamps, wiring, fuses, etc.Bulb in handle glows when circuit is complete (bulb included).Pointed 3-3/4'' (95 mm) probe makes checking easier.Deluxe 3.5'' (89 mm) long handle with nylon top holds replaceable bulb.36'' (914 mm) test lead with alligator clip.Replacement bulb: Cat. No. 69130
-
Series C63 -
Teledyne Defense Electronics Relays & Coax Switch
Series C63 solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin mini-DIP package. These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:C63-10 1A, 60Vdc Load; 8-20mAdc Control; through-hole mountedSC63-10 1A, 60Vdc Load; 8-20mAdc Control; surface mounted
-
Part No. ZD20CF -
Teledyne Defense Electronics Relays & Coax Switch
Series ZD20CF solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin DIP package These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:ZD20CF 2A, 60Vdc Load; 8-20mAdc Control; through hole mountedSZD20CF 2A, 60Vdc Load; 8-20mAdc Control; surface mounted
-
Part No. ZD24CC -
Teledyne Defense Electronics Relays & Coax Switch
Series ZD24CC solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin DIP package These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:ZD24CC 0.5A, 80Vdc Load; 8-20mAdc Control; through hole mountedSZD24CC 0.5A, 80Vdc Load; 8-20mAdc Control; surface mounted
-
505B -
Red Phase Instruments Australia Pty Ltd.
Field testing kWh meters is easy, field testing CTs when live is much more difficult. Our admittance tester can test CTs live with 50Hz or 60Hz current in the metering circuit. This technique does not confirm the accuracy of a CT but it will detect faults that give metering errors, such as shorted turns, metering circuits shorted to ground and tampering of CTs. CT faults can cause large revenue losses. Admittance testing only adds 10 minutes to a routine polyphase meter test, giving cheap insurance.
-
9107A -
Innovative Products of America
The #9107 Electric Brake Force Meter with Dynamic Load Simulation and Circuit Testing (patents pending) is designed for use on 7-spade equipped vehicles. This new technology automatically recognizes the electronic signature of both Integrated (ITBC) and aftermarket Trailer Brake Controllers, simulates trailer load and displays real-time, brake-controller output gain and application time. It can quickly troubleshoot truck-side tow circuits, e.g., tail lights, turn signals, 12V+, reverse and ground condition and the 25 ft. cable allows for one-man, in-cab testing.
-
Smiths Interconnect
Our fixed and mobile positioning systems featuring TECOM technology are used in range telemetry, flight termination, airborne and ground datalink, target tracking and jamming, signal intelligence, and direction finding applications. Positioning systems range from man-portable to 7 meter installations. Both positioning/controlling systems and turnkey solutions are available with reflector and feed assemblies reaching 0.5 to 325 GHz. With all positioners designed to meet environmental MIL-STD requirements, developing complete solutions for harsh conditions has become one of our core capabilities.
-
TE6-0707 -
Hangzhou Tonny Electric & Tools Co., Ltd.
*Used to locate hot circuits and troubleshoot primary circuits on all 6, 12 and 24 volt systems.*Suitable for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses..*Convenient screwdriver-type handle*Heavy Duty probe *Heavy plastic handle and insulated ground clipTesters light up to indicate testing result*Durably designed for a long service life.*Lights for easy visibility.*Heavy duty coil cord or straight cord (optional).*Materials: plastic/metal
-
SSG 3000 -
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR SSG 3000. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* high surge energy in each voltage range
-
SeaBat T20-S -
Teledyne Marine RESON B.V.
The T20-S is a new addition to the leading SeaBat product range engineered from the ground up to evolve with your business.Combined with the all-new Subsea Sonar Processor the T20-S provides the highest quality survey data in a fully integrated sonar processing and data storage unit housed in a subsea pressure vessel. Smaller form factor and reduced operational power to extend mission time for battery powered underwater vehicles. Internal data storage for self-contained survey solution, and interfacing via standard Ethernet to reduce integration time.
