Showing results: 436 - 450 of 580 items found.
-
GMS2000 -
OptCom Company, Ltd
In this goniophotometer, the tested luminaire rotates in the prescribed burning position and around the vertical axle and a reflecting mirror rotates around the horizontal axle, meanwhile, a synchronous axle will rotate toward the opposite direction synchronously. The combined motion of the luminaire and mirror permit luminous measurement at the direction of any horizontal or vertical angle without tilting the luminaire, therefore, the luminous intensity will be not variation. The photometer head located at a fixed position of the limiting photomet- ric distance in front of the reflecting mirror to gather the light in each direction.
-
A.H.Systems, Inc.
A.H. Systems offers 10 models of portable antenna kits. Each kit provides all the reliable antennas, current probes and accessories needed to satisfy a wide array of customer requirements. Each component has a specific storage compartment in the carrying case therefore, loss and breakage are virtually eliminated. Cables, a tripod with azimuth and elevation head and a tripod carrying case accompany each antenna kit. Click on a model below to learn more about it''s characteristics and included antennas.
-
OLCT 60 -
Teledyne Gas & Flame Detection
The OLCT 60AD version allows the sensor to be installed remotely up to 15 meters (standard), allowing detection in inaccessible locations, or in Zone 0 in the case of the intrinsically safe (IS) version. The detector units are made of 316L stainless steel, and are rugged and resistant to corrosion. Pre-calibrated sensors can be disconnected by turning the head of the unit. These “smart” sensors can be calibrated outside hazardous areas.The OLCT 60 is equipped with non-intrusive access to a safe menu. In hazardous areas, calibration can be done with an operating mode in accordance with safety rules.
-
Model PECVD-60-M -
TEK-VAC INDUSTRIES Inc.
Retrofittable with RF-DC-Laser Ablation Modules. High Temperature Substrate Heating, 4" Diameter. High Power Magnetron Head, 600W Microprocessor Temperature Control. Standard Model equipped to handle four gas inputs, expandable. Adaptable for RF or DC Plasma. Top Loading, Compact Footprint. Broad Operating Pressure Range (10-4 to 760 torr).
-
Test Head Engineering, LLC
Nest and Pod Fixtures are used to test components and sub-assemblies. They typically are built in an array and the devices under test are subjected to tests that simulate operating conditions or life-cycle testing. Test Head Engineering is experienced in providing nest and pod testers that meet the connectivity, ergonomic and mechanical requirements of component testing.
-
HEAD acoustics GmbH
Sound, vibration, status and reference variables, voice, audio data and more: HEAD acoustics is setting the standard in data acquisition. We offer flexible systems for mobile applications and operation in the laboratory. Our data acquisition systems can also be expanded flexibly using various software and hardware modules.
-
Bierer & Associates, Inc
Digital Voltage Detector is designed for easily indicating AC voltage on Underground primary, Over head primary and Transmission conductors up to 999 kV. The large digital display can be seen and read at distances up to 50'. Unit is perfect for large system voltages from 4kV to 765kV Phase to Phase.
-
Model 3800 -
Jinan Testing Equipment IE Corporation
The main body of this unique extensometer remains stationary during testing, held in position by the adjustable magnetic base included. Only the very light, small traveling heads move as the sample elongates during a test. These attach to the sample with small spring clips. Each head pulls a cord out from the extensometer as the head moves. These models use high precision, low friction potentiometers, and, as a result, have a wide range of factory selectable outputs. The extensometer is driven by an excitation voltage and has output proportional to the input. They can be provided with high level outputs (approximately 2-8 VDC) or ones that mimic strain gaged devices (2-4 mV/V). When set to mimic strain gaged extensometers, the Model 3800 can be used with virtually any signal conditioning electronics designed for strain gaged sensors. The potentiometers employ a hybrid wire wound around conductive plastic, which provides excellent long term stability. The output from the extensometer is readily interfaced with most existing test controllers, and may be directly input to data acquisition systems and chart recorders. Please let us know at the time of order what type of output and connector you require.
-
MC389 -
Manncorp
The MC389 sets new standards for SMT pick and place speed, precision, and flexibility. Based on the MC Series’ durable ball-screw and rotary-encoded drive train, its three heads and on-the-fly vision allow accurate placement of any SMD (including 01005 chips, µBGAs, and 12-mil pitch QFPs). With an enormous placement area of 650 mm x 460 mm (25.6" x 18.1") and a capacity for up to 160 Smart Tape and Stick Feeders, the MC389 can easily be configured for virtually any high-mix project.
-
InnoVista Sensors
With its choice of casings, wide range of actuators, variety of connections and high degree of resistance to impact and splashes, Crouzet Switches offers limit switches available in the following ranges: Metal body, Plastic body, Special products and Products for severe environments. Their main characteristics are: IP6x seal, a wide range of actuators (plungers and rollers), rotary heads with momentary action, positive break contacts, compact size, etc. They also offer the option of having special levers, prewiring, connection via ISO cable glands, etc.
-
LS-500 -
Panasonic Industrial Devices Sales Company of America
The LS-500 Series Amplifier-Separated Type Digital Laser Sensor offers high-class Laser Sensors able to detect very small objects with a processing speed of down to 60µs. The new full stainless steel M6 housing is robust and optimally suited for applications in harsh environments. The unique controller can handle Thru-Beam, Diffuse Reflection and Retroreflection Laser Sensor heads. All Sensors are equipped with two digital outputs, and cable-type Sensors offer an additional analog output, opening new dimensions in the detection of small objects.
-
Rohde & Schwarz GmbH & Co. KG
To meet the measurement challenges of 5G device testing in the mmWave (mmW) frequency spectrum Rohde & Schwarz offers the R&S®CMPQ, a fully integrated solution from a single supplier. The R&S®CMPQ consists of the R&S®CMP200 radio communication tester, the R&S®CMPHEAD30 remote radio head and the R&S®CMQ200 shielding cube. The R&S®CMPQ provides accurate and reliable measurement results under radiated conditions.
-
Bowers Group
Bowers Group offers a range of both standard and bespoke measurement solutions for a variety of gauging applications. As the world’s leading bore gauge manufacturer, our application heads can be fitted directly onto our XT range of internal micrometers to create a flexible, modular measuring system. Whether you’re measuring threads, grooves, splines, sphericals, or deep holes, we have a standard solution to suit. If you’re looking for something completely bespoke, our team has the skills and expertise to solve your measurement problem.
-
1000Z -
Adcole Corp.
The Adcole Model 1000-Z features both optical and tactile measuring heads to deliver high precision surface measurements of camshafts, crankshafts and turned parts. The non-contact interferometric probe greatly expands on the measurement capabilities from the diamond tipped contact probe of the standard Adcole 1000 gage, as the optical accessory can precisely measure surface finish of cam track groove sidewalls, cam track bottom grooves and more. Profilometers such as the 1000-Z quantify surface roughness and are relied on to maintain quality and identify potential problems in the manufacturing and coating process.
-
HDI Compact -
Metron3D
The HDI Compact 3D scanning system eliminates the tedious work involved with manually scanning an object. Save time and get stunning results everytime. The HDI Compact is an automated 3D scanning solution. The rotary table automatically spins the object and stops at predetermined intervals. The scan head captures high resolution, accurate 3D scans of an object each time. Once the object spins a full 360 degrees, all the scans are then automatically cleaned up and merged together to create a full digital 3D model.
