Showing results: 451 - 465 of 569 items found.
-
10780C -
Keysight Technologies
The Keysight 10780C is a highly-sensitive, lowest-cost Keysight receiver used with laser interferometer positioning systems. One receiver is used per measurement axis (including wavelength tracker). Configured with Keysight electronics, laser heads, cables and optics, the Keysight 10780C receiver allows you tailor a precise positioning system for your exact application requirements.
-
M-HD-360A -
Fuzhou Metricu Technology Co Ltd
Analog camera testHD-TVI camera test, HD-CVI camera test, AHD camera testDC12V 1A power outputVGA input, support 1920 x 1200P 60FPSAuto HD, auto recognize HD coax camera type and resolutionUTP cable test, detect the near-end, mid-end and far-end fault point of the network cable crystal head
-
LF1 set -
Langer EMV-Technik GmbH
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
-
QTOUCH1404C -
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
iTrans2 -
Teledyne Gas & Flame Detection
The iTrans2 infrared gas detector employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs. With the optional HART Communication Protocol, the iTrans2 offers remote diagnostics, set-up or calibration by superimposing a high-frequency current across the industry standard 4-20mA analog line.
-
RMS-1000 -
ECOPIA
Accurate and powerful performance. - Possible to get much accurate resistivity value by taking 8 raw data. - Good to check ohmic contact by flowing forward and reverse current.2. We provide various sample mounting board and probe head and tips.3. We have an optional item which can measure in variable temperature. - Room Temperature ~ 300dC.
-
6HP-9060 -
Prokit's Industries Co., Ltd.
Switchable X1/X10/X100 attenuation with reference switch positions. Break-resistant center conductor & wide compensation range. Flatter response, sharper leading edges. Faster rise time and replaceable cable probe head tip and ground lead. Max. input voltage: 600V/1200V (DC-peak AC). Includes BNC adapter, IC tip, insulating tip & trimming tool.
-
ASTel -
Radian Research, Inc.
Three-phase Meter Test Equipment of ASTeL 3.2x.x series system is a fully automatic system enabling simultaneous, multi-position calibration and legalization of electric energy meters. The automatics include power sources, reference standards, stand controllers, photoelectric scanning heads, separating transformers, and other elements of the system. All these elements are controlled through a Windows based executive program.
-
HMV-G Series -
Shimadzu Corp.
This micro hardness tester features a built-in CCD camera for standardized automatic length measurement. Hardness can be measured simply and accurately with easy-touse PC software. The lineup also includes fully automated (FA) machines equipped with an electrically driven revolver mechanism and electrically driven XYZ. A manual machine with an optical head and models with color cameras are also included in the lineup.
-
MCLEDV4 -
Manncorp
The MCLEDV4 Pick and Place machine features four vision-equipped placement heads mounted on a high-precision, ball-screw-driven gantry for fast, accurate LED assembly on rigid LED tube boards up to 47"/1.2 meters long, circular LED bulb boards and flexible LED strips. MCLEDV4 handles standard and irregularly shaped LEDs, including domed LEDs, from 0.6 x 0.3 mm to 8 x 8 mm (20 x 20 mm available with optional bottom vision). Special tape feeders with brushless motors hold up under round-the-clock production.
-
Fluke Calibration
Employing good connector practice when using an RF calibrator not only avoids measurement errors and minimizes connector repeatability uncertainties but also reduces risk of damage to connectors and equipment. The 96000CONN and 9600CONN connector kits include a range of adapters and torque wrenches intended for use with the 96000 Series RF Reference Sources (9600CONN for the 96040A and 96000CONN for the 96270).The 9600CONN connector kit includes one each of 50 Ω and 75 N-Type male-female adapter for use with the 96000 Series levelling head as a “connector saver” or “sacrificial connector” to avoid risk of damage when making connections to UUT/DUT instruments.
-
SFT3542HA -
Hangzhou Softel Optic Co., Ltd.
SFT3542HA SD encoder modulator is a professional high integration device which includes encoding, multiplexing, scrambling and modulation. It supports 8 to 24 CVBS inputs, one DVB-C tuner input and 128 IP input with Data1 (GE) and Data2 (FE) port. It also supports DVB-C RF out with 4 adjacent carries, and supports Data1 (GE) output port to support 4 MPTS out. This full function device makes it ideal for small CATV head end system, and it’s a smart choice for hotel V system, entertainment system in sports bar, hospital, apartment…
-
SY-8218 / SY-8219 -
IWATSU Electronic Co., Ltd.
Soft magnetic components made of ferrite play an important role in electric components as they are used in a broad range of applications from low-frequency applications such as yokes for micromotors, to high-frequency applications such as flyback transformers, deflecting yokes, high-frequency transformers and magnetic heads. In actual operation, these magnetic components display characteristics different from DC magnetic characteristics or characteristics measured with an LCR meter.
-
Test Head Engineering, LLC
Test Head Engineering's cable-end fixtures are used in the production of cable harnesses and in the testing of finished products. They are the long-lasting "connector" to the test system - taking the place of connectors that would quickly exceed their cycle life and produce erratic test results. Cable-end fixtures are used in the automotive and heavy equipment industries, but are also applicable wherever low cycle-life connectors are used - including RF cables.
-
TX-MT-100 SERES -
Test-X Fixture Products
Test-X MT-100 Series mechanical kits are an inexpensive solution for testing smaller printed circuit boards and other devices.The MT-100 Series features a 1/2" thick FR4 probe plate and a 3/8" thick Lexan top plate. Precision alignment is assured through tooling holes in both the probe and top plates. Units are available with a 2-1/2" pan or an upper head assembly
