Showing results: 271 - 285 of 355 items found.
-
64G5 -
North Atlantic Industries
NAI's latest generation 6U VME multifunction I/O and communications board, the 64G5, can be configured with up to six intelligent function modules. Ideally suited for rugged military, industrial, and commercial applications, this low-power/high-performance, board delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
68DT1 -
North Atlantic Industries
The 68DT1 is a 3U OpenVPX™ board featuring up to 96-Channels of Standard Functionality (SF) DT1 module-type or Enhanced Functionality (EF) DT4 module-type Discrete I/O functions [foptioned, factory configurable].48-Channels are dedicated as input (voltage or contact sensing with programmable, pull-up/pull-down current sources). An additional 24 or 48-Channels are programmable for either input or output (current source, sink, or push-pull) switching up to 500 mA per channel from an applied 3 – 60 V external VCC source (or sink to ISO-GND). The 68DT1 can sense broken input connections and whether an input is shorted to +VCC or to ground. Additional features of the DT4 EF are listed below. The 68DT1 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for pull-up resistors or mechanical jumpers.
-
75D4-H2 -
North Atlantic Industries
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
3U cPCI 75C5 -
North Atlantic Industries
NAI’s 75C5 is a 3U cPCI Multifunction I/O and Communication Board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed Analog-to-Digital (A/D) channels and 28 Discrete I/O programmable channels, or with a reference power supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
75D4 -
North Atlantic Industries
NAI’s 75D4 is a 3U cPCI High-Density I/O and Communication Board with a single, high-density function module slot. In addition, the motherboard also includes an option for an integrated four-channel RS232/423/422/485 serial communication complement. This low-power/high-performance board is ideally suited for rugged defense, commercial aerospace, and industrial applications.
-
78CS2 -
North Atlantic Industries
NAI’s 78CS2 is a 6U cPCI Multifunction I/O and Communication Board designed for applications requiring Digital-to-Synchro/Resolver (D/S) stimulus output, as well as I/O and communication functions. This board contains five independent function module slots. The board can be configured for 10 D/S channels, or for D/S in combination with I/O and communication modules. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
75C3 -
North Atlantic Industries
NAI’s 75C3 is a 3U cPCI multifunction I/O and communication board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed A/D channels and 28 Discrete I/O programmable channels, or with a reference supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
68G5P -
North Atlantic Industries
The 68G5P is a 3U OpenVPX board that can be configured with up to three NAI smart I/O and communication function modules. Uniquely designed, the 68G5P provides external access via PCIe x1 and/or SATA II interfaces directly to supported NAI function modules, providing external host SBC function expansion. Additionally, the 68G5P is on NAI’s certifiable product line development roadmap supporting DO-178C and DO-254 design assurance guidelines for safety-critical applications. Ideally suited for rugged Mil-Aero applications, the 68G5P delivers off-the-shelf solutions that accelerate
-
68C3 -
North Atlantic Industries
NAI’s 68C3 is a 3U OpenVPX multifunction I/O and communication board with three function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
68G5E -
North Atlantic Industries
The 68G5E is a 3U OpenVPX board that is configured with an Ethernet Switch module (choose the ES1, 12-Port GbE Cu legacy unmanaged Ethernet Switch, or the ES2 16-Port Cu GbE managed Ethernet Switch with optional 4x 10GBASE-SR 850 nm multimode Fiber Optic interface) and provides additional support for one NAI smart I/O and Communications function module. Uniquely designed, the 68G5E provides ‘independent’ Ethernet Switch capabilities and can operate as a MFIO board end point with access via the 1 x1 PCIe and/or 1x 10/100 Ethernet motherboard Control Port which hosts the NAI Ethernet Protocol Server/Listener application for direct GbE MFIO control. Ideally suited for rugged Mil-Aero applications, the 68G5E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
68G5 -
North Atlantic Industries
NAI’s latest generation 3U OpenVPX Multifunction I/O and Communications Board, the 68G5, can be configured with up to three intelligent function modules. Ideally suited for rugged military, industrial, and commercial applications, this low-power/high-performance board delivers off-the-shelf solutions that accelerate deployment of SWaP-C optimized systems.
-
78C2 -
North Atlantic Industries
NAI’s 78C2 is a 6U cPCI Multifunction I/O and Communication Board with six independent function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
67C3 -
North Atlantic Industries
NAI's 67C3 is a 6U OpenVPX Multi-function I/O and Communication Board with six function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Trig-Tek™ 260B -
Astronics Corporation
Delivers up to 80 channels of digital I/O for observing and/or recording 16 to 64 channels of pressure or temperature. Consists of a motherboard that connects up to four daughterboards to the IP 1553 serial bus.
-
GX3788 -
Marvin Test Solutions, Inc.
The GX3788 is a user configurable, FPGA-based, 3U PXI multi-function card which supports digital and analog test capabilities. The card employs the Altera Stratix III FPGA which features over 45,000 logic elements and 1.836 Kb of memory. The GX3788 is based on the GX3700 FPGA card and includes an integral daughter board which provides (8) differential input, 16-bit, 250 MS/s A to D converters and (8), 16-bit, 1 MS/s, D to A converters. The module's FPGA is pre-programmed, providing access to all digital and analog functions. Alternatively, users can program or modify the FPGA , allowing user to adapt the module to their own specific test needs. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
