Showing results: 451 - 465 of 628 items found.
-
64970 -
Lisle Corp.
Replaceable in-line fuses protect both the meter and tester in the event a high current source on the vehicle is left on. The multimeter is bypassed with the switch during connection in case of a power surge. The tester and meter can remain connected until other computer systems shut down, isolating the drain. As a convenience, stacking banana connectors are used on the tester. This allows voltage to be measured on various locations on the vehicle during the drain test, using standard test leads.
-
LDS-6 -
Doble Engineering
The Doble LDS-6 is a highly sophisticated digital measuring system for partial discharge detection and analysis. It is trusted as a valuable tool for factory and laboratory testing.The LDS-6 can be used to test a variety of high voltage apparatus. Use the LDS-6 to perform PD quality tests on motors, generators, transformers, MV and HV cable systems, switchgear and additional HV accessories.The LDS-6 complies with IEC 60270, VDE 0434 as well as various IEEE and other standards.
-
OAI
The OAI Integrated I-V Test System is perfect for R&D as well as production, the OAI Integrated I-V Test System delivers extremely accurate solar cell performance measurement. OAI’s advanced fully Integrated I-V Test System is designed to overcome the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match any type of solar cell’s high capacitance and slow dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell I-V parameters and efficiency while leading to the most accurate test results.
-
7128C -
Peaceful Thriving Enterprise Co Ltd
This is an auto-ranging, high accuracy and stable hand held clamp meter to make electrical maintenance safe and easy. With special designed IC to support true RMS, the meter is available to measure AC/DC voltage to 600V, AC/DC current to 600A and resistance to 60MΩ; also having the capability to test diode, continuity, frequency and non contact voltage sensing. Sub switch included Function Select, Value Hold, Range Select, Relative Value Measurement, Inrush Current Indication, Hz/Duty Cycle, Illumination and Back-light.
-
M3406A -
Keysight Technologies
Interface to the LRU in avionics test solution Up to four channel MIL-STD-1553 bus interface with full error injection and detection Concurrent Bus Controller, multiple Remote Terminals (31), and Bus Monitor operation capabilities Data capture filtering, 100% bus recording, and physical bus replay Variable output voltage signal and software selectable bus coupling modes 10 high voltage (up to 30 V) programmable DIO lines PXI trigger generation on 1553 bus events
-
ITIG -
Electrom Instruments
The iTIG III is the industry’s most advanced electric motor tester and winding analyzer. Bringing confidence to motor repair companies, industrial end users, OEMs, and manufacturers of rotating equipment, the iTIG III features over 20 high- and low-voltage tests including high frequency surge and partial discharge.Choose multiple tests to run automatically in a sequence or select single tests. Report results with the easiest to use instrument available. Manually operate voltage dial or set up for automatic operation. Carry the iTIG III in the field or use it as a benchtop device. Connect to an external portable power pack for testing up to 40kV. The iTIG III is the most versatile and easy-to-use tester available.
-
MS 1527 -
Meltronics Systemtech
The Semi-ATE is used for testing the analog ADC. It shall carry out the functional test on ADC analog module. The ATE shall have all necessary IO signals on the connector end. The semi-ATE can carry out the functional tests on ADC analog module with host PC or laptop. It provides +15V, -15V, +5V & -5V to module and +2.5V high precision reference voltage. It can able to control keysight N6700B Power supply mainframe using RS422 interface.
-
Neutronics Manufacturing Co.
Measure DC resistance of transformers windings etc. Introduction: The NMC ''TDR'' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. ''TDR'' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. ''TDR'' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.Principle: The constant current generated is fed to the resistance under test through the current terminals and the voltage drop across the resistance under test is measured and displayed in ohms. A true four terminal measurement is used to eliminate the need for lead resistance compensation.
-
CM55 -
Martindale Electric Co. Ltd
The CM55 is a pocket sized high performance AC Clamp meter measuring AC current, AC/DC voltage and resistance with continuity test. The compact rugged design enables accurate and reliable current measurement down to 10mA resolution without the need to break into the circuit.The CM55 has a CATIII 600V safety rating and is the ideal tool for residential and commercial electricians.
-
1805 ER -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Test test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Battery check function.● Calibration performed with supplied test leads.
-
LX-686 -
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface,．·Up to 1500Vdc/1000Vac Test Voltage ,．·256 Max. Test Points , (Max of all series)．·500 Max Files Memory,support USB or PC unlimited expansion,．·Arc detection level 0-9 ,auto prompt．·Adopted high resolution colour 640*480 TFT LCD ,．·Providing Single-End ,Multi-segment ,Standard ,and Spot test of wire.．·Auto Scan and Auto Pin Search ,．·The system provides advanced instant open-circuit, short-circuit, continuity test,．·Intermittent Conductance Test,．·Intermittent Open/Short Test ,．·Full Programming Sequence Test ,．·Versatile I/O Ports for application ,．·Statistics and Print Function,．·Provide REMOTE interface, communicate with PLD auto test fixture,．·Provide personalized customization according to different requirements,
-
40-137-201 -
Pickering Interfaces Ltd.
These Power Relay Modules are suitable for applications requiring power relay switching with high density. The feature 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 39 x SPST version, the range also includes a 32 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
40-137-101 -
Pickering Interfaces Ltd.
These Power Relay Modules are suitable for applications requiring power relay switching with high density. This version features 2A current and voltage to 110VDC/250VAC, they are configured as Single Pole Single Throw (SPST). Connections are made via front panel mounted 37 or 78-pin D-Type connector.Along with this 32 x SPST version, the range also includes a 39 x SPST, 2A version and a 16 x SPST, 5A version - go to Also in the Range above to learn more.Typical applications will be found in Automotive Test, Aerospace Test and Power Cell Test applications.
-
RK7112 -
Shenzhen Chuangxin Instruments Co., Ltd.
The tester is applied to the home appliances, computer peripheral equipment, electric products, communication products, lighting products, small home appliance products, lighting equipment, electronic components, transformers, motors, compressors, electric heat pipe, wire, cable and high voltage safety system’s withstand voltage and leakage current test, as well as it’s an indispensable dielectric
-
KT7193 -
Ketai instrument (kunshan) Ltd.
● 3 3/4 digits 3999 count● Extra high DC/AC current measurement● Data hold to capture measurements● Backlit display is easy to read under any light condition● AC current measurement up to 1500A● DC current measurement up to 1500A● DC/AC voltage, resistance, capacitance, frequency and temperature measurement● Diode and continuity test● Accessories included: 9V battery, carrying case, test leads, K typetemperature probe, English manual, gift box
