Showing results: 76 - 90 of 155 items found.
-
3564 -
Abaco Systems Inc
The 3564 is a four channel comparator board with a common mode range of -150V to 150V on the two differential inputs and a DAC per channel to set trigger levels. The high common mode range and DC coupling provides a robust solution to level detection and triggering.
-
5047 -
Abaco Systems Inc
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
5147 -
Abaco Systems Inc
ECM P/N 5147 provides two channels of 12 bit A/D conversion using the Analog Devices AD9235, and is suitable for medium resolution high speed applications. The two differential inputs are terminated in 120 ohms and buffered with a gain of 1 differential amplifier. Differential Input range is +/-3.0V. Sample rates are 20MHz per channel with a 5MHz 4 pole elliptical analog input filter.
-
5093 -
Abaco Systems Inc
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
5085 -
Abaco Systems Inc
ECM P/N 5085 provides two channels of 24 bit A/D conversion suitable for high resolution low speed applications, which include bridge circuits, thermocouples, RTD and voltage measurements. For bridge applications each channel provides a fused +5 Volt or a current source drive.
-
5081 -
Abaco Systems Inc
The 5081 provides four channels of 12 bit digital to analog voltage output, with multiple single ended output ranges. Each channel is software selectable for 0 to +5V, 0 to +10V, +/-2.5V, +/-5V, +/-10V or -2.5 to 7.5V ranges. The outputs reset to 0.0 volts on power up.
-
5089 -
Abaco Systems Inc
The 5089 provides eight channels of 12 bit A/D conversion using the Analog Devices AD7328, and is suitable for medium resolution medium speed applications.
-
7925 -
Chroma ATE Inc.
Chroma 7925 is an automatic inspection system for TO-CAN package. The appearance defects over 30 um like lens scratch, partial are clearly conspicuous by using advanced illumination technology. Because the height variation of tray and package exists, Chroma 7925 can calculate the focus distance and compensate to overcome the variation with auto focus function.
-
7940 -
Chroma ATE Inc.
Chroma 7940 wafer chip inspection system is an automated inspection system for postdiced wafer chip inspection.
-
7505-01 -
Chroma ATE Inc.
Chroma 7505-01 is the newest multi-function optical inspection system that equips with the capability of measuring 1D, 2D and 3D at the same time. Penetrating reflection measurement is used for 1D film thickness measurement to measure the non-destructive film thickness on transparent and translucent material.
-
7505-05 -
Chroma ATE Inc.
Recent advancement in optical inspection technology continues to find its path into a variety of market applications. Innovative automated optical testing has become essential and indispensable in areas such as effective dimensional measurement to ensure product manufacturability and process control.
-
7505-K009 -
Chroma ATE Inc.
The Chroma 7505-K009 Inline Printing Quality Automated Optical Inspection System equipped with high-resolution camera can perform 2D defect detection that is suitable for Roll to Roll processing and on-line control. Both front and rear sides can be inspected at the same time.
-
58620 -
Chroma ATE Inc.
The Chroma 58620 Laser Diode Characterization Station is a state-of-the-art full turnkey system specially designed for laser diode testing. Features range from macro inspection of the facet or aperture active area to a full suite of electro-optical parametic tests.
-
7505-02 -
Chroma ATE Inc.
The 7505-02 Automated Optical Inspection System is integrated with high speed camera to shoot Roll to Roll manufacturing processes of ITO (Indium Tin Oxide) film, RFID and FPC that is Line-scan Image Inspection System with PC-based structure.
-
7945 -
Chroma ATE Inc.
Chroma 7945 wafer chip inspection system is an automated inspection system for pre and post diced patterned wafers. Change kits enable switching between various applications by allowing different carriers including metal frame or grip ring.