Showing results: 166 - 180 of 325 items found.
-
Matrox Imaging
Matrox Imaging provides developers with the industry's most comprehensive frame grabber family. Hardware ranges from boards designed for very cost-sensitive applications, to frame grabbers integrating flexible, high-rate acquisition and pre-processing capabilities. Acquire the video format of choice through support for SD, HD and non-standard analog, DVI-D, Camera Link®, Camera Link HS™, CoaXPress®, GigE Vision®, IEEE 1394 and SDI.
-
Series MBT-G -
Kepco, Inc.
Kepco's MBT-G series (denoted by suffix "G") are bench-style instrumentation power supplies that offer a choice of control methods including direct entry keypad, slew up/down keys, rotary controls and three communications ports: IEEE 488.2, RS 232 and Kepco's single address, multiple instrument long range serial bus. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
T7610 -
COMET SYSTEM, s.r.o.
PoE Web Sensor with built-in temperature, relative humidity and atmospheric pressure sensors.High precision capacitive polymer sensor ensures excellent long term calibration stability and ultimate accuracy. Dual line LCD is an advantage. Power over Ethernet feature according IEEE 802.3af is supported. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio and specific enthalpy.
-
pixus technologies
1U to 4U rack-mounted enclosure with 482.6 mm (19") mounting brackets (may be offset approximately 100 mm to the rear). Two backplane slots can fit in each 1U of chassis height (standard 0.8” pitch) with rear plug I/O options. Enclosure cooling from left to right with EMC and ESDcompatible configuration. Optional: Hot swap-compatible power supply units with current splitting for redundancy operation (2U). Conforms to IEEE 1101.1/10/11,
-
Acoustics for Communications
Audio, acoustics and electroacoustics testing and assistance for your product. * Audio Laboratory equipped with precision instruments from Bruel and Kjaer and others. * Emphasis is on product and component analysis not general acoustics. * TIA, ANSI, IEEE, ITU-T, ETSI, AES, UL, EN, IEC standards expertise.
-
Model #:PE-200 -
Pansco, Ltd
The PoE Tester Pro is designed for speed testing and verifying standard active and passive PoE networks as well as measuring power level of a PoE system even with reversed polarity on IEEE 802.3 af (PoE), 802.3 at(PoE+) and 802.3bt(PoE++) type3 compliant standard PoE.
-
EWK-M2-AC9260 -
ADLINK Technology Inc.
- Bluetooth 5.1- IEEE 802.11ac wave 2 (Wi-Fi 5)- Operating Temperature : 0°C to 70°C (-40°C to 75°C extended)- Compact M.2 2230, A/E key form factor with cable and antenna kit to support flexible installation
-
JRE 0814-A -
JRE Test, LLC
Testing tall devices? The 0814-A stands up to any test up to 18 GHz! Featuring a wide swing open door with durable latch handle, this enclosure is ideal for testing IEEE 802.11 a,b,g devices such as; WLAN, VoIP, access points and other RF devices.
-
BXL Series -
IBEKO Power AB
BXL is an extra load unit designed to be used with DV Power’s BLU series battery testers. However, this unit is a universal add-on device. Because of that, it is compatible, as an additional load, with any other discharge/capacity tester in the market.In case when discharge current exceeds the capacity of a single BLU device, BXL can increase the discharge capacity. There are no limitations on the number of extra load units that can be connected in parallel to the main battery tester.A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way. Also, all instruments are in accordance with battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.These units can be used on any type of battery string, such as lead-acid, Li-Ion, Ni-Cd, etc. They test battery strings with voltages in the range of 5,25 – 500 V DC. On the other hand, current up to 250 A can be discharged through the BXL internal structure.The instrument simulates a constant resistance load during the discharge test. Several resistances can be set for different battery nominal voltage levels. This makes BXL extremely flexible in selecting its load capabilities.
-
XES-2T6 -
SWISSON ag
The XES-2T6 is a six plus two port Gigabit Ethernet switch with two ports being aggregated to a high throughput, redundant trunk link. The six other ports are individually assignable to groups (IEEE 802.1Q VLANs) that may participate in completely independent networks that do not interfere with each other. Thanks to the graphic OLED display, the encoder knob and a push button for each of the six configurable ports, the switch is intuitive to setup and the configuration is done in next to no time.
-
Junxy Energy
JUNXY Battery Monitoring Systems are designed in accordance with IEEE Battery Maintenance recommendations. This allows you to maintain a safe and secure system with Real-time monitoring, which will minimize the probability of a failure and optimize the service life of the battery. JUNXY Battery Monitoring Systems not only monitor the batteries, but also the external parameters which could affect the performance of the system, providing added security. It is a powerful tool for mitigating and preventing costly downtime due to unexpected system failure.
-
UNH IOL
BitPhyer is a family of hardware platforms used to test the IEEE 802.3™ MAC, Flow Control, PCS and RS layers for Ethernet devices, including Automotive Ethernet. This platform is based on Xilinx FPGAs and custom built hardware which are used to create a flexible bit-level based test system.
-
ProDAQ 6100 Series -
Bustec Ltd.
Ethernet-based LXI is changing the way engineers and scientists perform test and measurement and data acquisition. As more and more PCs ship without expansion slots, customers are faced with the problem of replacing their test and measurement and data acquisition equipment. Bustec believes in the power of distributed systems and the use of IEEE standards.
-
TopJTAG Probe -
TopJTAG
TopJTAG Probe is an easy-to-use boundary-scan (IEEE 1149.1 JTAG) based software for hardware debugging. The software allows to view and control pin states of the devices in a JTAG chain. TopJTAG Probe can be of invaluable help to monitor/control pins of fine-pitch and BGA chips and to check PCB interconnects for shorts and opens.
-
JT 57××/RMIC -
JTAG Technologies Inc.
The new-concept, industrial JTAG-powered PCB tester-programmer the JT 57xx/RMIc ‘CombiSystem’ comprises a sleek base-level 19″ rack-mount chassis assembly that can house up to four customer-specified modules chosen from various JTAG (IEEE 1149.x) controllers, digital IO and analog IO and other measurement modules.