Showing recent results 46 - 60 of 380 products found.
-
MBT-G - Kepco, Inc.
MBT Power Supplies with option "G" can serve as an interface between the IEEE 488.2 instrumentation bus and Kepco's single address, multiple instrument long range serial bus.
-
TCR180PEX - Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. The output format is independent from the incoming IRIG signal - a perfect solution to your IRIG conversion requirements. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device.
-
GPIB - Amida Technology, Inc.
AMIDA ATI-488 is a GPIB card with PCI interface. It is fully compliant with IEEE 488.1 and IEEE 488.2 standards and Supports Windows 95/98 /Me/NT4.0/2000/XP operation system with Plug & Play capability. The driver library not only contains windows development tools for Visual C++、Borland C++ Builder、Lab-windows、Visual Basic、Delphi、Lab-view but also provides NI-like commands. By using the library, users are capable of developing and transferring their application program easily. Moreover, with built-in interactive user interface can control instruments without coding.
-
C2000 - Spectrum Digital, Inc
Digital Signal Processor in socket operating at 100 Mhz18 K words on chip zero wait state RAM64 K words on chip FLASH ROM256 K bits serial I2C EEPROM memory20 Mhz clock2 SCI UART channels2 eCAN channelsExpansion connectors (analog, I/O)(unpopulated)Onboard embedded IEEE 1149.1 JTAG controller with USB interface+5 volt only operation with supplied adapterOnboard IEEE 1149.1 JTAG emulation connectorCompatible with eZdsp Wire Wrap Prototype CardRoHS Compliant
-
Megger Group Ltd.
Megger has introduced a new system capable of performing comprehensive health checks on power transformers. They offer routine and advanced electrical tests techniques described and recommended in international standards such as IEEE, IEC and CIGRE.
-
TTRT 01B S3 - Amperis sl
The TTRT-01B S3 is Amperis’ fourth generation, micro-processor based, single phase, and automatic transformer turns-ratio tester with rechargeable-battery powered. The TTRT-01B S3 uses the IEEE C57.12.90 measuring method to determine the transformer turns-ratio.
-
LPCI-3488A - ADLINK Technology Inc.
ADLINK LPCI-3488A GPIB controller interface card, fully compatible with the IEEE 488 instrumentation control and communication standard, is capable of controlling up to 14 stand-alone instruments via IEEE 488 cables. It is designed to meet the requirements for high performance and maximum programming portability. The built-in 2KB FIFO and a block transfer mode provide up to 1.5 MB/s GPIB transfer rate. With the APIs that are compatible with NI-488.2* and VISA support, the LPCI-3488A provides the greatest compatibility with your existing applications and instrument drivers. (* NI-488.2 mentioned here is the trademarks and properties of National Instruments Corporation.)
-
852-11914 - B+B SmartWorx
Unmanaged Gigabit Power Over Ethernet media converter; 3 ports- two 10/100/1000Mbps copper ports providing PoE+ and one fixed fiber port, 1000Mbps, Single mode 1310nm with SC connectorsSupports Jumbo Frames (up to 10240 bytes)Supports LFPT, a diagnostic troubleshooting featureSupports IEEE 802.3af PoE+ (25.5W) standards; features configurable PoE reset on Fiber Loss of Signal (LOS)Rugged standalone metal enclosure with internal power supply; country-specific power cord includedSupports IEEE 802.3af PoE+ (25.5W) standards
-
857-11913 - B+B SmartWorx
Unmanaged Gigabit Power Over Ethernet media converter; 3 ports- two 10/100/1000Mbps copper ports providing PoE+ and one fixed fiber port, Multi mode 1300nm, SC connectorsCompact, rugged stand-alone metal enclosure with external power supply (included)Supports Jumbo Frames (up to 10240 bytes)Supports LFPT, a diagnostic feature that can be enabled to assist the end user in troubleshooting a failed segmentSupports IEEE 802.3af PoE (15.4W) and IEEE 802.3at PoE+ (25.5W) standardsMultiple mounting options (Desktop, DIN Rail or Wall-mount)
-
DPM-3 - Transducer Techniques, Inc
Was developed to read and edit Plug and Play Smart Sensors that are compliant to the IEEE 1451.4 Standard. TEDS, or transducer Electronic Data Sheet, is a set of electronic data in a standardized format defined within the IEEE 1451.4 standard. This data specifies what type of sensor is present, describes its interface, and gives technical information such as sensitivity, bridge type , excitation, etc. This information is stored in an EEPROM chip attached to the sensor. By having this chip, the sensor can identify and describe itself to the network and or Smart Load Cell Meter (DPM-3), thereby easing automatic system configuration.
-
SSI-TRES - Transducer Techniques, Inc
Was developed to read and edit Plug and Play Smart Sensors that are compliant to the IEEE 1451.4 Standard. TEDS, or transducer Electronic Data Sheet, is a set of electronic data in a standardized format defined within the IEEE 1451.4 standard. This data specifies what type of sensor is present, describes its interface, and gives technical information such as sensitivity, bridge type , excitation, etc. This information is stored in an EEPROM chip attached to the sensor. By having this chip, the sensor can identify and describe itself to the network and or Smart Load Cell Meter (DPM-3), thereby easing automatic system configuration.
-
808-38522 - B+B SmartWorx
Applications: Fast Ethernet, OC3 and other optical linksPowerful Digital Diagnostics Monitoring Interface (DDMI) for troubleshootingMSA-Compliant with ITU-T G.957, G.958 and IEEE 802.3u10/100/1000 and 1000 Mbps Copper OptionsExtended Temperature
-
TTRT 01 S3 - Amperis sl
The TTRT-01 S3 is Amperis’ fourth generation, micro-processor based, single phase, and automatic transformer turns-ratio tester with line power only. The TTRT-01 S3 uses the IEEE C57.12.90 measuring method to determine the transformer turns-ratio.
-
TTR-3D Series - Amperis sl
The TTR-3D of ratio meters are high precision instruments, designed to measure turn ratios, phase displacements, excitation currents of single phase and three phase power, distribution and instrument transformers in conformity to the IEEE C57.12.90 & IEC 60076
-
Hilkar
Generator Neutral Grounding Cubicles are designed to minimize fault damage incurred by generators, maintain sufficient fault detection and improve power system reliability. Generator Neutral Grounding and Lead Cubicles are manufactured as for IEEE or IEC standards.
