Filter Results By:
Products
Applications
Manufacturers
IPACK
Mezzanine standard supporting 16 bit transfers at 4 MHz.
-
product
CompactPCI
cPCI4IP
The cPCI [CompactPCI] compatible cPCI4IP design adds 4 Industrypack compatible slots to your cPCI host. The cPCI4IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI4IP is a 6U 4HP cPCI design with 4 IP slots.
-
product
Compact PCI
cPCI2IP
The cPCI [Compact PCI] compatible cPCI2IP design adds 2 Industrypack compatible slots to your cPCI host. The cPCI2IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI2IP is a 3U 4HP cPCI design with 2 IP slots.
-
product
Industry Pack I/O Products
Acromag IndustryPack mezzanine IP modules deliver maximum I/O density when used with industry-standard IP carrier cards for VME, PCI, CompactPCI or PCI Express. These plug-in Industry Pack modules give you mix-and-match flexibility and high channel density to save your valuable card slots. Combining different IP types on one carrier simplifies the design of a low-cost, custom I/O board.
-
product
IndustryPack Module
IP-OptoISO-16
The IP-OptoISO-16 is an IndustryPack Module with 16 optically controlled FETs [switch]. Each FET acts as a single pole normally open photovoltaic relay. The solid state approach has several advantages including bounce free operation, low on resistance, long life, fast switching, and higher reliability when compared to relays.
-
product
IP-Parallel-BA1 "IP-Tape"
The IndustryPack compatible IP-Tape design adds 48 digital parallel IO lines to one slot of your carrier board. The IO is dedicated to a DTC interface. Other interfaces can be implemented. The DTC interface has 22 Address, 16 Data plus Parity, 4 control and 5 status lines. Parity is automatically generated in write mode and checked in read mode.
-
product
IP Parallel IO
IndustryPack compatible IP-Parallel-IO with counter and timer design adds up to 48 digital parallel IO lines to one IP slot of your carrier board.
-
product
IP-QuadUART-485
The IndustryPack compatible IP-QuadUART-485 design integrates a quad UART onto an IndustryPack module. The UART (16C854) features 128 byte FIFOs for RX and TX ports on each channel. The UART is supported by an advanced IP module interface implemented within a Xilinx FPGA.
-
product
PCI card with 3 IP sites
PCI3IP
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solutions.
-
product
Standardized Bus Interface
IP-429-II
Connect to your Avionics with IP-429. Pick 2,4,6,or 8 ARINC 429 compatible receivers and 1, 2, 3, or 4 transmitters. Transorb protected IO. Software programmable transmit rates [100K or 12.5K]. Time Tag on received data. IndustryPack campatible with 8 or 32 Mhz. bus operation.
-
product
16-Bit D/A Analog Output
PMC230A
PMC230A modules have eight 16-bit D/A converter (DACs) to provide highly-accurate analog voltage outputs. A unique two-piece board design brings the proven reliability of Acromag’s IndustryPack® (IP) A/D modules to a PMC format. An IP230A module is embedded on a PMC interface card that maintains maximum performance and transparent communication to the host.
-
product
2-slot IndustryPack Carrier
CPCI-100A-BP
The CPCI-100A-BP 2-slot IndustryPack carrier for 3U CPCI is available with back-panel I/O via the CPCI J2 connector. The carrier provides an 8 MHz IndustryPack clock for each slot. The standard 8 MB memory space is available for each IndustryPack site.
-
product
Universal Voltage Signaling PCI Card w/ 5 IP Slots
PCI5IP
If you want to use IndustryPack¨ modules with your PCI system then the PCI5IP is the choice for you. The PCI5IP combines features you need with simplicity and speed. Up to 5 IP modules can be installed. 32 bit and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection.
-
product
PC/104+ Card with 4 IP Slots
PC104p4IP
If you want to use IndustryPack modules with your PC/104+ or PC/104-Plus system, the PC104p4IP is the choice for you. The PC104p4IP combines features you need with simplicity and speed. Up to 4 IP modules can be installed. Standard 16 bit IPs plus 32 bit, and double wide modules fit right in. Each slot has independent operation - control, clocking, IO, power filtering and protection. The PC104p4IP is highly integrated with the PCI and IP interfaces closely coupled within the same FPGA.
-
product
PCIe Adapter for 3 IP Modules
PCIe3IP
IndustryPack® Modules are an important part of solutions for Embedded situations. Rugged, small, light ... just right for many applications. IndustryPack® Modules require a carrier to adapt them to the system. Dynamic Engineering has carrier solutions for a variety of formats. PCIe3IP is designed to support PC computer based solutions. Solutions available for PCI, PC104p, cPCI, VPX and planned for cPCIexpress, PC104e.
-
product
IndustryPack modules
PC104pIP
If you want to use IndustryPack modules with your PC/104+ system then the PC104pIP is the choice for you. The PC104pIP combines features you need with simplicity and speed. One IP module can be installed per carrier. Multiple carriers can be used in a stack. The PC104pIP is highly integrated with the PCI and IP interfaces closely coupled within the same FPGA
-
product
IndustryPack system trouble shooter
IP-DEBUG-IO II
IndustryPack system trouble shooter providing testpoints on all of the IP IO signals. Loop back is as easy as wire-wrap. Custom feedback signals are supported with socket and power connector support. Now with 2 ribbon cable connectors to support in system debugging.
-
product
Digital I/O
IP-DIGITAL482
IP-DIGITAL482 is a single-wide IndustryPack configured to maximize the number of digital I/O lines. The 48 lines are accessible as individual bits or as bytes. These lines may also be used for 8-bit and 16-bit I/O with handshake lines. IP-DIGITAL482 is a drop-in replacement for the IP-DIGITAL-48.
-
product
Slave Dual Industry Pack Carrier
CPCI-SIP-3
The new CPCI-SIP-3Module provides a 3U high performance flexible I/Oscheme, that supports industry standard IndustryPacks. Choose from over a 100 different IndustryPacks from Alphi Tech and others. For applicationrequiring low cost, high density I/O or unique combinations, the CPCISIP-3 is the perfectsolution.