Showing results: 1051 - 1065 of 1289 items found.
-
GO-SCAN C-VIEW -
Teledyne ICM
Go-Scan C-view is a light weight ruggedized real time X-ray imaging system specifically designed for hand-held inspection such, among other, Corrosion Under Insulation (CUI) inspection. It includes a high speed and high resolution CMOS imager and a battery-operated 70kV x-ray tube designed for portable field operation. The video imaging system captures images and displays them on a hand held display in real-time.
-
LE7 -
Image Engineering GmbH & Co. KG
The iQ-LED is the latest development of Image Engineering. It is a multi channel LED light source that provides the possibility to generate the spectral characteristics of nearly every required light source in just one device. With its 22 different software controlled LED channels it is possible to generate a spectral match of standard light sources such as, D50, D55, D65, A, B, C etc. with very high accuracy.
-
CLEAVEMETER 3D -
Nyfors Teknologi AB
The CLEAVEMETER 3D™ is a non-contact interferometer designed for inspecting the end-faces of cleaved or polished optical fibers with cladding diameters of 125 µm to 1200 µm. It gives immediate and precise information on important end-face properties such as flatness, perpendicularity, hackles and dust. Based on the NYFORS CLEAVEMETER 3D™ design, in addition to producing sharp fringe patterns it also generates three-dimensional images of the cleaved fiber end.
-
FastX-APU -
Alacron
The FastX-APU framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX-APU, is a two thirds length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex FPGA before being sent to the PCIe (X4) Gen 2 switch to the host or the AMD APU.
-
IDS Imaging Development Systems GmbH
The functions of classic vision sensors - such as barcode readers - are usually strictly defined and hardly expandable. IDS NXT shows that there is a different way: the freely programmable platform is not tied to any predefined tasks. Instead, users can develop and install vision apps themselves and then change and set up various image processing tasks in a short time. App development does not require any additional specialist knowledge, because it hardly differs from the development of a "classic" industrial camera application. The possibility of installing different types of vision apps creates universal application possibilities in numerous application areas, for example in optical quality assurance, as an analytical device in medical technology, for surveillance tasks using face recognition or vehicle and person counting.
-
A2T -
U. S. Digital
The A2T is a single axis, digital gravity angle sensor. The A2T serves as a full 360 range absolute tilt sensing programmable level with either digital or analog output. Internally, a rotary bar coded disk is mounted to a weighted gravity driven wheel. A micro-controller strobes an LED to transfer the bar code image onto an optical linear array, then decodes the position every 2 mSec. Magnetic damping provides fast response and settling time while virtually eliminating overshoot and oscillations. An internal EEPROM stores field programmable parameters such as resolution, zero position, direction swap, and mode. This second generation design virtually eliminates the primary accuracy limitation of first generation inclinometers, which is sitation (hysteresis).
-
Agilent Technologies
Discover our selection of CGH + SNP Microarray software for your workflows and clinical research needs. Our selection includes the Cytogenomics Software which caters to the needs of cytogeneticists for analysis and triage of their CGH and CGH+SNP data from pre- post-natal, PGS and cancer samples. Our software suite includes Feature Extraction, that automatically reads and processes up to 100 raw microarray image files; Genomic Workbench which provides a powerful visualization tool for non-human CGH analysis; and SureDesign Custom Design Tool, which is an enhanced design application for customizing genomic targets. In addition to analysis tools, we provide Alissa Interpret an interpretation software providing powerful tools for visualization of key chromosomal aberration.
-
NEXTCOMPUTING, LLC
NextComputing’s Data Science Workstations featuring NVIDIA GPUs from PNY dramatically accelerate data analytics time to insights, enabling breakthrough data preparation, model development and training performance. These powerful workstations can aid in the advancement of medicine and research enabling scientists to tackle interoperable data development of AI-based intelligent applications unique to their workflows and accelerate areas like image analysis, scientific research, and drug discovery.
-
LINCam FLIM -
Becker & Hickl GmbH
*Easy to Use Like an Ordinal Megapixel CCD Camera*Spatial Resolution ~ 1024 x 1024 Pixels*Temporal Resolution (IRF Width) 50 ps FWHM*Single-Photon Sensitivity*Saturated Count Rate Up to 5 MHz*Excitation by bh BDS-SM Family ps Diode Laser*Works with All Commonly Used MicroscopesI*llumination via Single-Mode Fiber*Lens System for Image Transfer Into Camera
-
BCO, Inc.
System provides reliable automatic access to test points on a printed circuit under test providing rapid and accurate diagnostic measurements. Accomplished by an automated test probe with video image capability, under control of application software running on a VXI Test System utilizing LabVIEW. A VXI Prober Interface Module (VPIM), developed to Plug and Play standards, provides interface between prober and VXI Test System.
-
Applied Scientific Instrumentation
ASI Modular Microscope components consist of tube lenses along with adapters and accessories that either are primarily used in the collimated light space or adapters that are to be used on the image side. Collimated light adapters use the 38 mm diameter C60-RING system to connect components. Focus-side adapters attached to lens tubes with either a 30 mm diameter coupling to the I.D. of the C60-TUBE, or with a 50 mm coupling on the O.D. of the lens tube.
-
787314-01 -
NI
PXIe, 4-Port, GigE PXI Frame Grabber Module - The PXIe-8246 helps you acquire images in machine vision and scientific imaging applications that require high data throughput. This PXI Frame Grabber Module includes four RJ45 gigabit Ethernet (GigE) ports in a single-slot PXI Express … module and features power over Ethernet (PoE). Additionally, the PXIe-8246 includes a Vision Acquisition Software license.
-
VFI-1200 -
Arden Photonics LTD
The VFI is the interferometer of choice for industry leading photonics companies around the world. The VFI-1200 is an interferometric inspection system specifically designed for checking the surface quality and flatness of your cleaved or polished fibers. The VFI offers the perfect combination of a superb image quality with ease of use, and the reliability and robustness that our customers have come to expect from Arden products, resulting in fiber end face measurements that you can trust.
-
VFI-2000 -
Arden Photonics LTD
The VFI is the interferometer of choice for industry leading photonics companies around the world. The VFI-2000 is an interferometric inspection system specifically designed for checking the surface quality and flatness of your cleaved or polished fibers. The VFI offers the perfect combination of a superb image quality with ease of use, and the reliability and robustness that our customers have come to expect from Arden products, resulting in fiber end face measurements that you can trust.
-
FastX1703 -
Alacron
The FastX1703 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX1703, is a two thirds length raw form factor PCI board six basic 85 MHz Camera Link Channels or an extended Camera Link camera interface. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as LVDS or high speed analog formats such as UXGA or DVI. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, up to four PNX1702 500 MHz processors with 256MB memory each. Finally, the FastX1703 interfaces to the host computer through a 4xPCIe interface for state-of-the-art data acquisition.
