Showing results: 346 - 360 of 1119 items found.
-
KH3766 -
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
KH3760 -
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
KH3763 -
Beijing KeHuan Century EMC Technology Co,.LTD
The artificial power supply network (also called the power supply impedance stabilization network) should be able to provide a stable impedance to the device under test in the radio frequency range, isolate the device under test from high-frequency interference on the power grid, and then couple the interference voltage to the receiver.
-
VM-10, VM-20 , VM-30 -
UDEYRAJ ELECTRICALS PRIVATE LIMITED
High Voltage Meters measure AC and DC voltages of up to 30kV with high accuracy. The meter input impedance is as high as 1000 M ohm, making the meter suitable for measurement of voltages of high source impedance circuits. Meters are compact and light weight and can be conveniently used as a calibration meter.
-
PL-10 -
PINTEK Electronics
*MODEL:PL-10*IMPEDANCE:1.111MΩ*ACCURACY: ±0.25%*FREQUENCY B.W.:DC~50MHz*WORKING POWER:MAX. 1Watt*INPUT VOLTAGE:MAX.250VDC or 200V rms AC*DIMENSION:46mm(L)xΦ16mm(D)*WEIGHT:25g
-
FLC Electronics Inc
These amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance and fast response. The output is linear from DC up to megahertz range.
-
80SICON IConnect -
Tektronix, Inc.
IConnect software is the efficient, easy-to-use, and cost-effective solution for measurement-based performance evaluation of gigabit interconnect links and devices, including signal integrity analysis, impedance, S-parameter and eye diagram tests, and fault isolation.
-
MD75300 -
Matco Tools
*Safely acquire high voltage waveforms with this high impedance, active pickup*Works with spark plug wires and coil on plug ignitions with MDAUTOWAVE, AUTOWAVECAMO and MDAUTOWAVE2*Adjustable sensitivity increases waveform acquisition accuracy
-
Smiths Interconnect
Smiths Interconnect offers the industry's most extensive line of high reliability coaxial probes. Our coaxial probes provide a low noise, controlled impedance signal path with reliable and easy connect/disconnect options.
-
41800A -
Keysight Technologies
The Keysight 41800A Active Probe provides high input impedance from 5 Hz to 500 MHz. The Keysight 41800A is a valuable tool when used with a network and spectrum analyzer for circuit signal analysis.
-
International Testware Corporation
International Testware supports all major ATE models for today's semiconductor products.CredenceAdvantestCaesarHewlett-PackardLTXIMSSchlumbergerAndo...and MANY moreTeradyneMosaidOur Solutions offer:Mixed-SignalEMI ReductionR/FCustom TailoredLow NoiseReliable PerformancePrecise Length MatchingSuperior Impedance ControlCrosstalk "Immunity"Minimal Inductance
-
Langer EMV-Technik GmbH
The MP CI set up to measure coupling impedance is used to determine EMC characteristics of connectors and cables. The coupling inductivity defines the coupling inductance of external disturbance on the shield or on the ground with the desired signals. If the coupling inductivity is considered in the construction set-up and the pin or wire assignment of connectors or cables, then the connectors or cables will be more interference-resistant. The MP CI set-up for measuring coupling impedance can be used for following measurements at connectors or cables: 1. measurement of a single signal (common mode) 2. measurement of a symmetrical signal (common mode) 3. measurement of a symmetrical signal (differential mode)
-
Navigator II FCi -
Advanced Energy
The Navigator® II FCi is a standalone, microprocessor-controlled impedance matching network. Incorporating tuning elements adjusted by discrete solid-state switched capacitor arrays, the matching network is driven by the need to achieve fast, accurate tuning across wider impedances. With a similar form, footprint, and tuning ranges as traditional counterparts, these matches offer tuning times in the millisecond range compared with the one-second range typical of traditional matching networks. This high-speed matching technology is optimized and suited for critical, power sensitive, short duration plasma process steps such as Atomic Layer Etch (ALE).
-
16034E -
Keysight Technologies
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
SR554 -
Stanford Research Systems, Inc.
The SR554 is a low-noise, transformer-coupled preamplifier optimized for source impedances between 0.05 Ω and 1 kΩ. With an input noise of only 0.1 nV/√Hz, the SR554 can be used in a wide range of low-noise applications.