Showing results: 361 - 375 of 1126 items found.
-
International Testware Corporation
International Testware supports all major ATE models for today's semiconductor products.CredenceAdvantestCaesarHewlett-PackardLTXIMSSchlumbergerAndo...and MANY moreTeradyneMosaidOur Solutions offer:Mixed-SignalEMI ReductionR/FCustom TailoredLow NoiseReliable PerformancePrecise Length MatchingSuperior Impedance ControlCrosstalk "Immunity"Minimal Inductance
-
Langer EMV-Technik GmbH
The MP CI set up to measure coupling impedance is used to determine EMC characteristics of connectors and cables. The coupling inductivity defines the coupling inductance of external disturbance on the shield or on the ground with the desired signals. If the coupling inductivity is considered in the construction set-up and the pin or wire assignment of connectors or cables, then the connectors or cables will be more interference-resistant. The MP CI set-up for measuring coupling impedance can be used for following measurements at connectors or cables: 1. measurement of a single signal (common mode) 2. measurement of a symmetrical signal (common mode) 3. measurement of a symmetrical signal (differential mode)
-
Navigator II FCi -
Advanced Energy
The Navigator® II FCi is a standalone, microprocessor-controlled impedance matching network. Incorporating tuning elements adjusted by discrete solid-state switched capacitor arrays, the matching network is driven by the need to achieve fast, accurate tuning across wider impedances. With a similar form, footprint, and tuning ranges as traditional counterparts, these matches offer tuning times in the millisecond range compared with the one-second range typical of traditional matching networks. This high-speed matching technology is optimized and suited for critical, power sensitive, short duration plasma process steps such as Atomic Layer Etch (ALE).
-
16034E -
Keysight Technologies
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
SR554 -
Stanford Research Systems, Inc.
The SR554 is a low-noise, transformer-coupled preamplifier optimized for source impedances between 0.05 Ω and 1 kΩ. With an input noise of only 0.1 nV/√Hz, the SR554 can be used in a wide range of low-noise applications.
-
WA301 -
Aim-TTi
Extends the output range of function generators30 Volts peak to peak output swingDC to 1MHz bandwidthHigh impedance input, 0dB to +20dB gain50 Ohm and 600 Ohm outputs20dB switchable output attenuatorFully protected output
-
WinTek s.a.s.
Measures in Loop Insulation Quiescent Condition.DC characteristic (I, V) and characteristic I (t).Feature of Ringtone.Transmission and impedance characteristics.Call functions.Response functions."Power Failure" functions with auxiliary power supply.Special functions programmable by the user.
-
S93027B -
Keysight Technologies
The S93027B enables to control Maury Microwave’s LXI tuner as the impedance tuner and measure the noise figure of unmatched devices (Gamma opt. < 0.9) with the N524xB PNA-X with option 029 and the S93029B noise figure measurement software.
-
85138B -
Keysight Technologies
The Keysight 85138B is a precision, low-reflection dc to 50 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 85138B has a 2.4 mm female connector.
-
85138A -
Keysight Technologies
The Keysight 85138A is a precision, low-reflection dc to 50 GHz load for terminating a 50-ohm coaxial system in its characteristic impedance. It is intended for use as a calibration standard. The Keysight 85138A has a 2.4 mm male connector.
-
ZAHNER-Elektrik
Electrostatic noise from the laboratory environment disturbs measurement signals and decreases data quality drastically for small current signals. Our Faraday Cage enables effective shielding for measurement on high impedance or low current samples.
-
SCS
Verifies Critical Grounding Parameters of a FacilityMeasures AC voltage, DC voltage, EMI voltage and AC impedanceProvides Accurate Measurements of Ground Impedance on a Working ToolMeets ANSI/ESD S20.20 requirements for AC impedanceIdentifies Potential EOS Generators
-
Saluki Technology Inc.
The SE4002 is a low-noise, ultra-high input impedance preamplifier with excellent common-mode rejection. It is designed to work with any Saluki digital lock-in amplifier. The preamplifier minimizes noise and pickup in the connecting lines and reduces measurement time in noise-limited experiments.
-
FEMTO Messtechnik GmbH
Switchable gain up to 100 dB (x 100,000)Bandwidth DC to 100 kHzDC-drift 0.6 µV/°CInput noise down to 0.4 nV/√HzSwitchable AC/DC-couplingLocal and remote controlInput impedance up to 1 TΩ
-
MCH-8817A -
MCH Instruments Co.,Ltd.
Features:*Multiple functions with easy operation *Big white back-light LCD display*6 typical test frequencies *3 typical test levels: 0.1V, 0.3V and 1.0V*2 selectable output impedances: 30Ω and 100Ω