Showing results: 481 - 495 of 1119 items found.
-
TDR-410 -
Sonel S.A.
*Location damaged power cables.*Fault location copper telecom cables.*Coaxial cable fault location.*Fault location wiring infrastructure.*Detection of breaks, short circuits, damage caused by dampness and other changes in impedance of the cable.*Graphic depiction of damage the cable with automatic indication the distance to fault on the screen.
-
V792 -
CAEN S.p.A.
The Mod. V792 is a 1-unit wide VME 6U module housing 32 Charge-to-Digital Conversion channels with current integrating negative inputs (50 Ohm impedance).For each channel, the input charge is converted to a voltage level by a QAC (Charge to Amplitude Conversion) section. Input range is 0 ÷ 400 pC.
-
JFW Industries
JFW offers blocking and non-blocking matrix switches. They are available with 50 Ohm or 75 Ohm impedance. The Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted commands. Our RF Matrix Guide steps through the advantages for each matrix type.
-
SE-1006 -
KILTER ELECTRONIC CO.,LTD
● Measure the impedance of any type battery which voltage below 48V.● A perfect tool for batteries used in vehicle, emergency lighting, alarm, sprinkler systems, UPS devices, business security and any system using batteries to provide power, especially for lead-acid battery used in vehicle, electromotion car etc..
-
SE-1004A -
KILTER ELECTRONIC CO.,LTD
●Measure the capacity ●Measure the impedance of the battery●Used as a battery charger●For Li-ion battery (mobile phone battery) and Ni-MH battery ●Capacity range:0~4.000Ah Accuracy: ±2% of reading Resolution: 1mAh●Voltage range: 0 ~ 5V Accuracy: ±0.5% of reading Resolution: 0.001V●Impedance range: 0~1000mΩ Accuracy: ±5% of reading Resolution: 1mΩ●Maximum charge end voltage: 4.400V●Minimum discharge end voltage: 0.000V
-
Chroma Systems Solutions, Inc.
Equipped with a host of powerful features: power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, waveshape synthesis and regulation test software
-
Radiometrics Midwest Corporation
One of the more difficult tests to understand is shielding effectiveness or transfer impedance. The data from these tests may vary dramatically based on the test method selected, test fixture, test setup, measurement sensitivity, test personnel, etc. At Radiometrics all shielding effectiveness test are performed or supervised by NARTE Certified engineers.
-
NI
PXI Transfer Switch Modules offer fast insertion times and low insertion loss to switch loads at RF frequencies. The modules also have 50 impedance that helps minimize reflections of the RF signal and protect your instruments. You can program the PXI Transfer Switch Module using the NI-SWITCH instrument driver.
-
JFW Industries
JFW’s online 50 Ohm Low power termination and mismatch load models are listed in the table below. JFW has been designing, manufacturing, and delivering quality terminations and mismatch loads for over 30 years. Our mismatch loads allow you to select the impedance mismatch your RF testing requires.
-
Radio Frequency Systems
RFS offers a comprehensive product line of FM combiners to suit a wide range of applications. The balanced (or constant impedance) bandpass design offers an expandable system that is built in a modular form enabling extra stations to be added at a future date. This configuration provides state of the art performance with the best frequency response and isolation attainable.
-
60-710-721 -
Pickering Interfaces Ltd.
The 60-710 is a Dual 24 x 8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has an impedance of 75Ω implemented using 50Ω SMB connectors. It is designed to provide a simple and scalable bidirectional matrix for video frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems.
-
40-739-002 -
Pickering Interfaces Ltd.
The 40-739-002 (PXI) and 42-739-002 (PXIe) are dual 16-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
40-739-006 -
Pickering Interfaces Ltd.
The 40-739-006 (PXI) and 42-739-006 (PXIe) are dual 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
42-739-002 -
Pickering Interfaces Ltd.
The 40-739-002 (PXI) and 42-739-002 (PXIe) are dual 16-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
42-739-006 -
Pickering Interfaces Ltd.
The 40-739-006 (PXI) and 42-739-006 (PXIe) are dual 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.