Showing results: 526 - 540 of 1119 items found.
-
40-782-522 -
Pickering Interfaces Ltd.
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
42-737A-901 -
Pickering Interfaces Ltd.
The 40-737A-901 (PXI) and 42-737A-901 (PXIe) are 8:1 USB multiplexers for switching USB1 and USB2 data and power connections with USB connectors. The data signal paths are 2-pole arranged as differential pairs as defined by the USB standard. The signal pair has a controlled differential impedance and the multiplexer has been designed for minimum insertion loss.
-
CX1152A -
Keysight Technologies
The CX1152A Digital Channel provides 8-channel digital trigger for the CX3300 Device Current Analyzer series, which is useful when a low power device with digital I/Os is evaluated. Only the CX3324A mainframe has the interface of this product. The input impedance of each channel is 10 MΩ in order to minimize the load current from the digital channel.
-
ELWIS -
Autoneum Holding AG
ELWIS (Evaluation of Light Weight Impedance System) offers a full and rapid characterization of porous materials based on the analysis of a single sample. The ELWIS system consists of the ELWIS-A and ELWIS-S components which can be used independently from each other although both applications are needed for a complete material simulation.ELWIS-A measures acoustic parameters that are needed to evaluate the acoustic performance of sound insulation and sound-absorbing multi-layer materials. An additional impedance tube for absorption measurements at higher frequencies is available for ELWIS-A.ELWIS-S measures structural parameters that are needed to simulate the dynamic and acoustic behavior of sound packages in the medium to low frequency range (including the "Poisson Ratio" for foam materials).ELWIS is very easy to operate: Thanks to its user-friendly software, the system can also be used to obtain reliable results by users with only limited experience in the characterization of porous materials.
-
Pasternack Enterprises, Inc.
Pasternack 75 Ohm SMB connector category includes dozens of part numbers, most are RoHS and REACH compliant. 75 Ohm SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SMB 75 Ohm connectors are built to precise microwave and RF industry specifications. Pasternack 75 Ohm SMB connector products are built in jack or plug gender with 75 Ohm impedance. SMB connectors in 75 Ohm impedance are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm SMB connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm SMB connector series is in-stock. Not only are these connectors with 75 Ohm SMB in stock, they will ship the same day as they are ordered.
-
Pasternack Enterprises, Inc.
Pasternack 75 Ohm TNC connector category has several part numbers, most of which are RoHS and REACH compliant. 75 Ohm TNC connector series in this category will terminate to coax or terminal. Our 75 Ohm TNC connectors are built to precise microwave and RF industry specifications. TNC 75 Ohm connector products are available in male or female gender with 75 Ohm impedance. 75 Ohm TNC connectors are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These 75 Ohm TNC connector designs include clamp/solder, crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm TNC connector series is in-stock. Not just in stock, these TNC connectors in 75 Ohm impedance will also ship the same day as they are purchased.
-
PCCextend 140 -
Sycard Technology
The PCCextend 140 was designed from the ground up to support the higher data rates and controlled impedance requirements of the CardBus interface. Fabricated on a six-layer board, the PCCextend 140 is designed to minimize signal degradation in the 33MHz CardBus environment. The PCCextend 140 is compatible with all release 2.1 and both 16-bit PC Card and CardBus-capable PC Card 95 sockets.
-
EMIC Corporation
The compact vibration generator is used for calibration of a vibrometer, measurement of mechanical impedance, excitation source for modal analysis and reliability test of a small light specimen. In particular, EMIC uses the world's first ceramic armature for the 512-D and 513-D vibration generator,making it possible to excite up to high frequency of 30 kHz (513-D can excite up to 24 kHz).
-
ETAP Enterprise
60364-4-41 StandardBS 7671 StandardEN 50122 StandardTN-C, TN-S, TN-C-S, TT & IT Earthing TypesElectric shock requirementsLoop impedance and current calculationTouch voltage calculation and evaluationCalculation considers resistance to ground / earthGround Fault Current Interrupter (GFCI) or Residual Current Circuit Breaker (RCCB) or Residual Current Detector (RCD) protectionReports in Crystal Reports and MS Excel
-
Analog Devices Inc.
Analog Devices offers a portfolio of sample-and-hold amplifiers and track and hold amplifiers that combine speed with precision. ADI sample-and-hold amplifiers can acquire a signal in 700 ns and hold it with a droop rate of 0.01 µV/µs. These devices are up to 14-bit accurate, with low aperture jitter and output impedance, and they are available in commercial, industrial, and military temperature ranges.
-
TS® 19 -
Fluke Networks
The Fluke Networks TS19 Test Set combines all the essential test set features at an affordable price. This test set was specifically designed for in-house telecom technicians. Its high impedance monitor prevents accidental disruption of service from clipping onto a data line while in monitor mode, thus ensuring the integrity of critical data lines.
-
MegiQ BV
Many of the well known VNA manufacturors offer very expensive calibration kits and special phase-stable cables (which costs almost as much a MegiQ VNA) for measuring impedances. This is useful for some special scientific measurements, or when working in the higher GHz, but a setup with an uncooperative cable and a bulky (N) connector is not suited for measuring the small devices that we are developing.
-
60-985-050 -
Pickering Interfaces Ltd.
The 60-985 series of LXI cables conform with the LXI WTB cable specification. They terminate in a 25 Pin Micro D connector at each end and use low loss silver plated cable incorporating 8 differential pairs each with separate shields. The cable to connector termination is designed to minimize inter-channel crosstalk and maintain excellent transmission line impedance.
-
60-985-005 -
Pickering Interfaces Ltd.
The 60-985 series of LXI cables conform with the LXI WTB cable specification. They terminate in a 25 Pin Micro D connector at each end and use low loss silver plated cable incorporating 8 differential pairs each with separate shields. The cable to connector termination is designed to minimize inter-channel crosstalk and maintain excellent transmission line impedance.
-
60-985-003 -
Pickering Interfaces Ltd.
The 60-985 series of LXI cables conform with the LXI WTB cable specification. They terminate in a 25 Pin Micro D connector at each end and use low loss silver plated cable incorporating 8 differential pairs each with separate shields. The cable to connector termination is designed to minimize inter-channel crosstalk and maintain excellent transmission line impedance.
