Showing results: 571 - 585 of 1119 items found.
-
M531 -
ETC
The M531 is a single channel USB arbitrary waveform generator compatible with USB 2.0 and USB 1.1 interface. The generator has two outputs: both generate same waveform, but with different peak-peak voltage. The low level output has 50ohm output impedance and maximal peak-peak voltage of 9V. There is no external power supply required to enable low level output (it is powered from USB bus).
-
11667L -
Keysight Technologies
The Keysight 11667L is a 50 ohm two-resistor type power splitter with BNC connectors. It is used with the E5061B network analyzer for power distribution network applications, such as DC-DC converter output impedance measurements with shunt-thru method (100 Hz to 10 MHz). It provides excellent amplitude (<0.2 dB) and phase tracking (+/-3), ensures highly accurate power splitting and low SWR minimizes measurement uncertainty.
-
Keysight Technologies
The Keysight DC blocks offer a new level of DC blocking with performance specified from 50 kHz all the way up to 67 GHz. Precision coaxial connector interfaces ensure an excellent impedance match across wide bandwidths, and come in a variety of RF connectors to fit your application needs. Two choices of DC Voltage ratings make these suitable for a wide range of applications.
-
10073D -
Keysight Technologies
The Keysight 10073D passive probe is our most rugged 500 MHz probe. With a 10:1 attenuation ratio and high 2.2 M ohm input impedance, it is ideal as a general purpose, high bandwidth passive probe for the Keysight 300 MHz - 1 GHz 6000 series, 7000, 8000 and 9000 Series oscilloscopes. The probe identification feature automatically configures the oscilloscope for the probe attenuation.
-
Chroma Systems Solutions, Inc.
Some of the key features to look for in an LCR meter (also known as an impedance meter) are: accuracy, test frequency, measured parameters, test voltage and test current. Additionally, an easy to understand display of test results and the ability to access and use these results has become increasingly important. Component testing often requires much more than simply a resistance, capacitance or inductance value at a given test frequency and stimulus voltage. An LCR meter or impedance meter must have the flexibility to provide multi-parameters over wide frequency and voltage ranges.
-
HCTS Series -
Shanghai Jiuzhi Electric Co., Ltd.
The HCTS Series Cable Heat Cycle Test System is designed to raise and control the temperature of conductor or other low impedance electrical loop to simulate the current loading conditions found in the electrical circuits up to 10000A.
-
Avtech Electrosystems, Ltd.
These instruments generate current pulses whose amplitude is largely independent of the load voltage. This makes them ideal for pulsing device whose voltage may vary with time (for instance, the voltage drop of laser diodes may vary with temperature, or explosive squibs which change impedance during ignition). This voltage independence is a trade-off with speed. If faster rise times are required, consider using pulsed voltage instruments instead.
-
Analog Devices Inc.
Analog Devices JFET input op amps or FastFET high speed (>50 MHz) input op amps provide high input impedance and ultralow input bias currents for high speed applications. The majority of our FET input op amps feature wide supply ranges from +5 V to 12 V or higher and feature rail-to-rail outputs enabling wide dynamic range.
-
ALTO-IRT-7000 -
Alto Inspection Corp.
ALTO-IRT-7000 (IMPEDANCE RESONANCE TECHNOLOGY ) FILM THICKNESS METROLOGY TOOL UTILIZES NON-CONTACT CAPACITIVE AND EDDY CURRENT TECHNOLOGY TO ANALYZE MICRO SECTORS ON COATED SURFACES THAT ARE 1000 TIMES SMALLER THAN ANY COMPARABLE EDDY CURRENT PRODUCTS. BUT MOST IMPORTANTLY, THIS UNIQUE IRT TECHNOLOGY ALLOWS FOR SOPHISTICATED ANALYSES OF THE CONTINUOUS AND DISCRETE FILMS BELOW 50 ANGSTROMS, DRAMATICALLY IMPROVING THE ACCURACY OF QUALITY CONTROL READINGS.
-
EZstat Pro -
NuVant Systems, Inc.
The EZstat Pro potentiostat/galvanostat uses a versatile menu-driven waveform generator (periodic or aperiodic) with preset battery cycling, Tafel plots, and cyclic voltammetry procedures.Users can program sequences of steps blending current and potential control with a resolution of 8 uS/point. EZstat Pro can perform electrochemical impedance spectroscopy (EIS) and uses active IR compensation. The instrument can interface with the EZpump peristaltic pump for flow batteries and fuel cells.
-
FLIR DM66 -
Teledyne FLIR
The DM66 digital multimeter is ideal for automation field service or electronics technicians, providing a comprehensive feature set including low impedance (LoZ) mode, frequency, diode, capacitance, and a Type K thermocouple input for temperature measurement. The multimeter combines rich features, precise measurements, and quality construction into a tool of exceptional value. Easy to use and built to last, the DM66 offers long-term stability for everyday use.
-
iP30z -
Buddipole, Inc.
The iP30z iPortable Antenna SWR Analyzer is designed for field use and is an excellent choice for working with the Buddipole line of antennas. This compact battery powered unit has an easy to read frequency display and measures SWR as well as Z (impedance) in the HF Band. The SWR readings quickly show you the actual VSWR measurement. This is the easiest way to adjust your antenna quickly in the field without any guesswork.
-
PCIe4LXMCX1 -
Dynamic Engineering
Simple and easy to use. Install PCIe4LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position. XMC´s with up to 8 lanes can be used. The PCIe lanes to/from the XMC are routed per PCIe specifications with matched lengths and impedance control.
-
ABex TM-1149Cx -
Konrad Technologies GmbH
The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
ECAD System 2005 -
CM Technologies Inc.
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.