Showing results: 361 - 375 of 877 items found.
-
National Technical Systems
PCB testing, or printed circuit board testing, begins with understanding that the PCB is the foundation for any printed circuit assembly (PCA).The circuit board is a top quality product that should not cause your end product to cost you money due to failures and recalls. NTS is an internationally accredited test laboratory approved for PCB testing including the bare PCB, the raw materials that the PCB is comprised of, as well as the finished PCA. The most commonly used PCB testing performance specifications for qualification, acceptance, and/or conformance are IPC-6012, IPC-6013, IPC-6016, IPC-6018, MIL-PRF-55110, MIL-P-50884, or MIL-PRF-31032.
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
Vogelsang & Benning
Test bench for electric machines and inverters in hybrid applications*Control of mechanical parameters*Verification of electrical properties*Checking the LL characteristics*Short circuit measurement*Recording the performance process*Noise measurement*Temperature measurement
-
Z-Axis Connector Company
Any flat substrate, or bumped substrate, can be compressed against Z-Axis Elastomeric Connectors to make contact. The picture illustrates a Z-Thru Z-Alloy Connector Frame used to connect the DUT (Device Under Test) to a circuit board.
-
TE6-0718 -
Hangzhou Tonny Electric & Tools Co., Ltd.
*For use on 6V, 12V and 24V DC systems*Tests high and low voltages on all vehicle circuits, including computerized engine and body controls*Dual color LED indicates red for power and green for ground
-
BK2019B -
BaKo Co., Ltd
With the BK2019B, you can test for open/short circuits, operating current and even vibration level. Because it has only one purpose, it is very easy to set up and use and it's so small it can fit into the average briefcase.
-
WABC -
Wuhan Sangao Electrical Test Installations Limit Co.
Acc to IEC and Relevant national standard, In the power transformer production, transfer and user test process, Transformer ratio test is necessary project, This can be used for quality supervision of transformer factory and the use process, prevent the transformer winding inter turn short circuit, open circuit, connection error, pressure regulating switch failure or contact fault.So our company development and production of automatic ratio tester in the original basis according to the user's site using requirements , make the operation more convenient, complete function, stable and reliable data, the testing speed is greatly improved.To meet the needs of all kinds of small medium and large transformer ratio test.
-
eloZ1-400 -
elowerk Testsystems
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the very latest generation, reliably detecting connection and assembly faults on printed circuit board assemblies. The eloZ1-400 is the compact version of the eloZ1. It is particularly suitable if there is only limited space to fit test appliances. The eloZ1-400 can also be used as a mobile test system.
-
PGT120 -
Eltex-Elektrostatik-GmbH
Electronic test apparatus for checking personnel grounding systems such as electrostatic wrist straps and conductive footwear. The unit is equipped with two separate measuring circuits and is therefore capable of checking wrist straps and footwear separately or in parallel. The test result is signaled visually, acoustically (only if error is detected) and via contacts.
-
Z-Axis Europe
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
1180 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Battery operated.● Solid state circuitry.● Battery check feature.● Automatic circuit discharge.● Three insulation test voltages(DC) : 250V, 500V, 1000V● Continuity test : 50 Ω● AC voltage measurement : 500V● Color-coded scale.● Fuse protected.
-
Autolink AL539 -
Autel
The AutoLink® AL539 OBDII & Electrical Test Tool supports all 10 modes of OBD II test for a complete diagnosis. Featuring the unique patented One-Click I/M Readiness Key, circuit test, starting and charging systems test, TFT color display, and built-in speaker, the versatile, easy-to-use AL539 will streamline automotive service and help ensure rapid, accurate diagnosis and timely repair.
-
767943 -
Wesbar
Plug these testers into any car connector and you will have an instant test of running light circuits. Features LED display to show completed circuit for the running lights left turn signal and right turn signal. Auxiliary and electric brake circuit are included on the 6-way tester and auxiliary, electric brake and battery charge are included with the 7-way tester. One piece units with internal ground. Proper installation and set-up of a brake control, when a trailer is not readily available, is possible with the 7-way tester. Current Monitor testing device is designed to assist in determining whether a tow vehicle's 7-way blade car end connector has been wired properly. (Current Monitor is an excellent diagnostic tool for installation, setup and troubleshooting of electric trailer brake controls.) The Trailer Tester is designed to help you quickly identify problems in the wiring of the trailer. This is done by testing the Left Turn, Right Turn, Tail/Marker, Brake and Back Up circuits on the trailer. The tester indicates approximate amount of current in each circuit (i.e. trailer battery). Brake Control Bench Tester is a test device designed to determine if a brake control is working properly. Checks brake control output, independent of vehicle wiring. Simulates many fault conditions including open ground, short circuit, open load and more.
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
Analog Discovery -
Digilent Inc.
The USB-powered Analog Discovery lets you measure, visualize, analyze, record, and control mixed analog and digital signal circuits of all kinds. It's small enough to fit in your pocket, but powerful enough to replace a stack of lab equipment. Driven by the free original WaveForms software, the Analog Discovery digital oscilloscope lets you build and test analog and digital circuits in virtually any environment, in or out of the lab.
