Filter Results By:
Products
Applications
Manufacturers
-
product
PathWave System Design (SystemVue)
PathWave System Design offers the most advanced prototyping and design platform for complex RF systems with faster simulation speed, near-circuit fidelity, libraries for radar, electronic warfare, satellite, 5G, and WiFi, plus enterprise integration with numerous partners.
-
product
Resistance Grounded Systems (HRG/LRG)
Neutral Grounding Resistors (NGRs) are used to limit the maximum ground-fault current. Restriction of fault current lowers hazards and reduces damage done to equipment. High Resistance Grounding (HRG) systems are often used on industrial and critical power applications to maintain system uptime during a first ground fault. HRG systems are also used in tripping applications to help control touch potential on portable loads and improve personnel safety.
-
product
Shallow TEM Magnetic System
WTEM-2Q
WTEM-2Q time domain shallow TEM system is one of our latest researchers, with all functions and advantages of domestic and oversea shallow transient electromagnetic survey systems, integrated with WTEM-1J/GPS TEM system receiver and WTEM-1X low-power transmitter. It features high transmitting power, short turn-off time, high reliability, strong anti-interference performance (atmospherics, 50Hz or 60Hz industrial frequency interference), lightweight and low power consumption.
-
product
Automatic and Accurate Inspecting Systems
Circuit AOI
The Circuit AOI system is designed to perform automatic and accurate inspecting systems. It integrates rigid mechanical system with advanced vision technology and manufactured and tested by strict is standards. It is suitable for circuit inspection for PCB/FPC, verification and repair. Innovation and unique inspection algorithms are applied to inspect open, short, protrusion, nick, scratch, pin hole, island, line width/space violation, object missing and others defects. AOI system can use offline setup project and check results. It will improve the throughput.Compare to halogen lighting, the full angle LED lighting of Circuit AOI can obtain the best image contrast and is good for different panel type inspection.
-
product
Real Time PCR Systems
Learn about Agilent’s Real Time PCR system including the newest generation AriaMx system, and find everything you need for your qPCR applications, from kits, instruments, enzymes, master mixes, reagents, optical cartridges, plastics, supplies to software and more. The AriaMx Real-time PCR System is a fully integrated quantitative PCR amplification, detection, and data analysis system. The AriaMx amplifies your productivity with its unique modular and flexible design, intuitive touch-screen interface, advanced, easy-to-use reporting, and 120+ attributes monitored via the built-in on-board diagnostics to help pinpoint assay or instrument issues as they arise.
-
product
Continuous Emission Monitoring System
CEMS
CEMS, the “Environmental Eye” for Source Emissions.A Continuous Emission Monitoring System (CEMS) is an integrated system to measure fuel flow, dust, and concentrations of air pollutants such as SO2, NOx, CO, CO2, THC and O2 in accordance with the applicable regulations for the emission source.
-
product
Automotive Supply Simulation System
Spitzenberger & Spies GmbH & Co. KG
The modularly constructed Automotive Supply Simulation System is a compact EMC-Test System for the execution of immunity measurements for pulse-shaped, line conducted disturbances at electronic equipment of motor vehicles. The high performance version enables tests of current-intense consumers or even complete vehicles
-
product
IndustryPack system trouble shooter
IP-DEBUG-IO II
IndustryPack system trouble shooter providing testpoints on all of the IP IO signals. Loop back is as easy as wire-wrap. Custom feedback signals are supported with socket and power connector support. Now with 2 ribbon cable connectors to support in system debugging.
-
product
Cleanliness Inspection System / Microscope
CIX90
The OLYMPUS CIX90 technical cleanliness inspection system is a dedicated, turnkey solution for manufacturers who maintain high quality standards for the cleanliness of manufactured components. The OLYMPUS CIX90 system makes it easy to quickly acquire, process, and document technical cleanliness inspection data to comply with international standards. The system is intuitively designed to guide users through each step of the process so that even novice inspectors can acquire important cleanliness data quickly and easily.
-
product
Eddy Current Test System
CIRCOGRAPH® Product Family
Foerster Instruments, Incorporated
The CIRCOGRAPH eddy current test system with rotating probes guarantees maximum detection sensitivity for exposed longitudinal surface defects on bright material. The test system is primarily used for wire drawing machines, Cu tube rewinders, and finishing sections in the bright steel sector. The individually tailored test systems by FOERSTER can be fitted with rotating sensors or CIRCOSCAN rotating discs. They scan flat and profiled material, e.g. when testing rails and billets.
-
product
FTIR Compact & Portable Systems
To meet the challenge of FTIR analysis in the field, Agilent has developed the world's smallest FTIR instruments. Our compact FTIR systems deliver the sensitivity and efficiency of a lab-based system, yet are fully portable. These portable FTIR systems feature integrated power supplies and our Flexscan and Exoscan technology for efficient scanning performance. Lightweight handheld FTIR optics and sampling modules enable advanced FTIR capabilities in field applications such as conservation and mineral identification.
-
product
Measuring Systems For Beverage Can Manufacture
OTP – Optical Tool Profile Gauge
Optik Elektronik Gerätetechnik GmbH
Optical measuring system for the inside profile of drawing dies for the 2-piece can manufacture.
-
product
Stack Gas Analysis System
ENDA-5000 series
Continuous simultaneous and high-precision measurement of NOx, SO2, CO, CO2 and O2.HORIBA has over 100,000 CEM systems installed and 30 years of quality and experience. That is the base on which HORIBA's new ENDA-5000 series of stack-gas analysis systems are built. These systems have a small footprint and use cross-flow modulated non-dispersive infrared (NDIR) and magneto-pneumatic detectors that are inherently drift-free. The ENDA-5000 series are superior continuous analysis systems that perform reliably for difficult exhaust gas measurements, when measurement errors cannot be tolerated. This CEM series features a new intuitive touch panel that makes every operation available with the touch of a single button. The ENDA-5000 series systems are also designed for ease of maintenance. They are ideal for a variety of uses, including emissions monitoring from steam boilers, refuse incinerators, and electric power generation plants to assure pollution standards are being met.
-
product
Torque Measuring and Monitoring System
WISER 4000
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
product
High Speed Camera Systems
MEMRECAM MX
The nac MEMRECAM MX is a robust, turnkey solution for multi-camera onboard and offboard automotive testing and occupant safety applications. Each system supports up to eight, tightly synchronized camera views, and integrates seamlessly with all current and legacy MEMRECAM imaging systems.
-
product
Satellite Terminal Geolocation System
Satellite Terminal Geolocation System is designed to identify and locate sources of satellite transmission such as satellite gateway, VSAT Hub and VSAT terminals etc. The system is useful to the intelligence and defense agencies to identify the sources of satellite transmission of their adversaries and locate the terminals on digital map.
-
product
Electromagnetic Field Analyzer System
A compact size electric antenna (The electric field analyzer system) that hasthe spectrum analyzer function. This instrument is most suitable to the radiation noise measurement ofelectric field from the system, such as the wireless power supply, that uses the frequency less than 30 MHz.
-
product
Pro Battery Monitoring System
iPQMS-Pro
The iPQMS-Pro is a real-time non-intrusive UPS battery monitoring system that measures 48 480 cells. The iPQMS-Pro battery monitoring system provides immediate warnings of battery deterioration which will prolong the life of UPS batteries and reduce battery maintenance and replacement while ensuring uptime.
-
product
Boiler Thermocouple Monitoring System
BTM
The Boiler Thermocouple Monitoring System is used to acquire and archive data from thermocouples mounted on boiler tubes. Since this system interfaces directly with Allen Bradley Control Logix PLCs via EthernetIP communication, significant cost savings can be achieved by using it as remote IO.
-
product
Power mixed test system
Power device or module with which are digitally controlled and memory can be measured per system.
-
product
Cylindrical Lens Measuring System
CLM
Optik Elektronik Gerätetechnik GmbH
CLM is a measuring system for geometrical parameters of cylindrical lenses for use in serial production.
-
product
Hall Effect Measurement system
HMS-5000
Constant current source + Van der Pauw method terminal conversion system
-
product
Optical Displacement Measurement Systems
ODS Series
The optical displacement measurement systems of the ODS series are specially designed for measuring the ultrasonic vibration displacement at bond tools of wire & flip-chip die bonders. The systems are highly accurate and very easy to use. That makes it the perfect tool for displacement based calibration of ultrasonic bond machines.
-
product
Analog IC test system
A paradigm shift has been occurred in Japan’s major brand WL25 series tester. Ultimate simple system is available by effective analog pin architecture.This cost performance system is covered analog IC extensively, which are high accuracy, speed and multi-site test function.
-
product
Magnetic Field Cancelling System
MR-3
3-axis magnetic field cancelling system for electron microscopes (SEM and TEM), electron and ion beam experiments, nanotechnology, biomagnetic investigations, etc. High reliability through rugged analog design. No tedious programming, no chrashs. More than 1000 MR-3 systems sold worldwide.
-
product
Electromagnetic Vibration Testing Systems
EV series
Labtone Test Equipment Co., LTD
EV series of electromagnetic vibration testing systems cover a wide range of forces ideal for many different applications. The electrodynamic shaker systems are well-suited for vibration testing products and structures of any size – from small components and electronic hardware to very large devices and structures.
-
product
SCTE35 And DPI Monitoring System
SCM200
The SCTE35 splicing message and advertisement insertion monitoring system can be used by service providers to monitor Ad placement opportunities and verify correct Ad insertion. The system will log all SCTE35 messages discovered in the transport streams and perform triggered recording for the verification of Ad insertion process.
-
product
Application-Specific Test Systems & Components
Ease system integration with Keysight System products and services. You can be sure you´re getting outstanding system-ready instruments, open software, and PC-standard I/O that give you the freedom to choose the best tools for your test, and the assurance that they´ll work together, every time.
-
product
Wind Measurement and Meteorological System
Moriah
Aeronautical & General Instruments Ltd.
MWS is a solid-state system with no moving parts, so providing a highly accurate, reliable and low cost of ownership system, which is ideal for supporting ship based aviation activities. The system comprises of 1 to 5 Solid State Wind Sensors, Dual Redundant Processor Unit, a range of Multi-Function Color Displays (8.4”, 10.4” and 15.0”) and utility Software/Graphic User Interfaces. In addition full Meteorological capability can be achieved with the inclusion of Air Temperature & Humidity, Air Pressure and Sea Temperature Sensors.