Filter Results By:
Products
Applications
Manufacturers
-
product
Touch Posi-Control System V2
DPC
The position control torque arm system helps manufacturers detect and eliminate costly screw-fastening errors during the assembly process. This position control system is designed to reduce the risk of improperly fastened screws, ensuring that every screw is in the correctly tightened in the correct sequence. A good tightening sequence ensures that an even preload distribution is achieved in the joint. Using a position control system is like putting the eyes and ears of a quality control manager where they are needed most - right on the assembly area.
-
product
3D Roughness Measurement System
IF-Profiler
The If-Profiler is a handheld 3D roughness measurement system for high resolution measurement of surface finish. You measure roughness of flat and curved components with only one system. Measurements are performed both profile based (ISO 4287) and areal based (ISO 25178). The measurement system achieves flexible measurements and applications at high measurement speed. Various positions and measurement fields are traceably and intuitively measured. The IF-Profiler is also used to measure geometries with steep flanks and various coatings.
-
product
BATTERY PACK AND BMSTEST SYSTEMS
DMC's Battery Pack Test Systems facilitate battery design as well as research and development for national laboratories and research institutions. They are deployed in end of line / production test stations for battery packs developed by major automotive manufacturers and their suppliers. DMC's battery pack test systems are designed to evaluate the battery as a complete system and validate a comprehensive range of battery pack functionalities, including:Power performance, Capacity, DCR / Internal ResistanceContactor and safety interlock functionsIsolation / Insulation ResistancesReporting of operating data through external communication interfaces (usually CAN)Cell VoltagesPack / Cell TemperaturesState of ChargeFaults / Diagnostic Trouble Codes (DTCs)Etc.Electrical characteristics / continuity of internal pack wiring / signalsCooling system operation
-
product
SSPA Systems (Indoor and Outdoor)
Paradise Datacom’s series of redundant amplifier systems provide the highest degree of earth station redundancy and reliability. Based on Paradise Datacom’s family of rugged and robust SSPAs, these systems provide the highest MTBF’s possible.1:1 C-Band Compact Outdoor SSPA SystemThese systems can be configured in either 1:1 or 1:2 redundant configurations using any of the Paradise Datacom family of SSPAs. While all Teledyne Paradise Datacom SSPAs are capable of internal 1:1 or 1:2 control, the RCP2-1100/1200 Redundant System Controller provides an extremely user friendly interface for complete monitor and control of the high power amplifiers in either 1:1 or 1:2 configurations.
-
product
Circuit Breaker Test System
AutoScan
AutoScan Circuit Breaker Test System is used for performing routine tests on circuit breakers and various other types of switchgear. This test system is designed to test vacuum circuit breakers, high voltage circuit breakers, and extra high voltage circuit breakers as per suitable standards.
-
product
Motor Drive Test Systems
Drive and motor systems present unique challenges for test systems and Intepro combines regenerative active electronic loads to reduce the energy needed to do the tests as well as sophisticate instruments and supply voltages to test these demanding applications and provide meaningful results for the electrical and mechanical power parameters.
-
product
Curved Needle Test Systems
The Instron® Curved Needle Testing System is ideally suited for testing needles used in wound closure or surgical procedures. This system provides a platform for two different needle testing solutions: one for curved needle puncture testing to ASTM F3014 and the other for cantilever bend testing.
-
product
Return Band Alignment System
6103/6106
Enable a single technician to perform return band alignment with this easy to use return band alignment system for CATV. This system consists of a headend signal level receiver/telemetry transmitter (the HECTER 6103) and a small, field portable, dual-carrier signal generator/telemetry receiver unit (HECTER'S PUP 6106).
-
product
Conventional Extractive System
ML660
The Teledyne ML®660 conventional extractive system is designed to extract and condition hot, wet stack gas for a dry basis measurement of any combination of SO2, NOx, CO, CO2, and O2. This system can be configured specifically for 40CFR60, 40CFR63, 40CFR75 compliance, and process control applications.
-
product
Phase Noise Test System
N5511A
The Keysight N5511A phase noise test system (PNTS) lets you measure at the limits of physics with readings down to kT (-177 dBm/Hz). The N5511A PNTS is a replacement for the gold-standard Keysight E5500 phase noise measurement system and is designed to meet the needs of phase noise power users.
-
product
On-Line Gas Analysis System
Titan-OL
The Titan-OL is a turnkey, process-ready gas analysis system. The analyzer and sample handling hardware can be wall or frame mounted in a NEMA enclosure suitable for use in production environments, including Class I, Div. 1. The integrated sampling system is fully purgeable and can handle multiple sample and reference lines.
-
product
Pressure Pump Control System
PumpLink
PumpLink is a pressure pump control system designed to configure to any pump / transmission in the industry.
-
product
Automated Visual Control System
Eyesystem 1.0
To develop a system for automated detection of rejects in the process of filling yoghurt into a bottle on a production conveyor.
-
product
Measuring Systems For Beverage Can Manufacture
URP 100: Universal Gauge For Ironing Rings, Punches, Necking Dies And Knockouts
Optik Elektronik Gerätetechnik GmbH
URP is the universal measuring system for rings and punches, special designed for 2-piece beverage can manufacture.
-
product
Low Voltage Test System
CKT T1
The CKT T1 is a compact size solid-state test system featuring 128 test points.
-
product
Continuous Emission Monitoring Systems
CEMS
IMR Environmental Equipment, Inc.
Continuous Emission Monitoring Systems (CEMS) is a class of hardware designed for extended process analysis.
-
product
Flex-plate Torque Sensing Systems
Advanced Telemetrics International
ATi’s FlexPlate Torque Sensing Systems permit in-vehicle Engine Output torque measurements.
-
product
Noise & Vibration Measurement Systems
Prosig P8000
Prosig P8000 noise & vibration measurement systems are compact, rugged & extremely accurate. The tough casing and low power requirements makes them ideal for mobile, in-vehicle or laboratory data acquisition. Units can be stacked to expand the system up to 1024 channels at speeds up to 100k samples/second/channel.
-
product
Precise Temperature Forcing System
TA-5000A Series
The ThermalAir TA-5000 Series of temperature forcing systems bring precise thermal testing capabilities directly to your test application, exactly localizing to where thermal conditioning temperature cycling is required. ThermalAir TA-5000 temperature systems provide flexible thermal test solutions for an array of products and technologies.
-
product
CMOS/CCD Production Test System
System 1828
The basic system consists of a 225 MHz pattern generator, 10 clock drivers, 6 DC biases, 1-4 channels of 10 MHz 14 bit analog data acquisition and/or 1-4 channels of digital acquisition. Additional options can be added to customize the system to meet your requirements.
-
product
Functional Test Trainer System
QT65
Qmax Test Technologies Pvt. Ltd.
Functional Test Trainer system, is a test system which can perform various Power- On functional tests of digital devices(ssl/MSI/LSIs and analog devices in the out- circuit and in-E conditions. Unified Library of vast number of devices to effectively test devices in in-circuit as well as out of circuit conditions.
-
product
Structural Health Monitoring System
SHM
Automated stationary structural health monitoring system (SHM) is a subsystem of buildings and structures control system which has been developed in accordance with the applicable requirements of the corresponding standards. It is used to detect a transition of the building state from operational into the state of failure, that may eventually lead to fatal accidents.
-
product
Flying Prober Test System
QTOUCH2204C
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.
-
product
HV Test Load Systems
B-1025-1
Design and manufacture of electronic and electromechanical devices and systems for our customers' special applications has been Ross Engineering Corporation's specialty for 44 years. Among these devices are our High Voltage Test Loads and Resistance/Capacitance Networks designed to simulate radar, communication, and television transmitter loads for testing up to 300kV DC or AC and 200kW. For example, one Test Load System required 4 separate simulated load networks to complete an 8kV, 14kV, 24/6kV, and 34kV high voltage testing system.
-
product
Terahertz Spectroscopic/ Imaging System
TAS7500 Family
The TAS7500 series is a family of compact and multipurpose terahertz spectroscopic / imaging systems. Utilizing the unique properties of the terahertz region (0.1 10.0THz) of the electromagnetic spectrum, these systems perform non-destructive analysis of pharmaceuticals, chemicals, communications materials, etc., without requiring a specially constructed analysis environment. Speed and ease of operation are the hallmarks of Advantest's terahertz analysis systems. In addition to industrial applications, the TAS7500 series is also an optimal choice for terahertz related research, leveraging Advantest's high-precision detection technology to provide best-in-class sampling performance.
-
product
Precigrader: Acoustic MSR System
Precigrader is an acoustic on-line strength grading system. The system is installed in more than 150 mills. It is used to determine common commercial grades in North America, including 1650 and 2100. A spring-loaded impact mechanism strikes the lumber as it passes. The resulting vibration is captured by microphones to determine the appropriate MSR grade.
-
product
Production Process Automation System
OPLAN
OPLAN v2.6 is a system for production process automation of a television company. The system supports all the stages of operation. From the content ingest, description and preparation, creation of preliminary line-ups and daily broadcasting schedules, registration of commercials and arrangement of commercial blocks, broadcast preparation and automation, to the control and analysis of broadcasting results.
-
product
Magnetic Field Cancelling System
MK-1
Single axis magnetic field cancelling system for MRI scanners and biomagnetic applications. This system is used when the magnetic field sensor cannot be placed within the shielded volume. For example, in MRI applications the sensor is usually installed outside of the shielding room because of the MRI scanner's high fringe field.
-
product
Multi-site Module Testing System
TCIII-3200ST
TurboCATS introduces a new line of redesigned TCIII-3200ST DDR4 and DDR3 multi-site module testing system - compact, high-performance, and equiped with enhanced productivity features. The TurboCATS TCIII-3200ST module test system features an optional 8, 16 or 64 module testing, in parallel, for high throughput on your production floor.
-
product
Multi-Functional Dynamic System Monitor
PFMonitor
The PowerFactory Monitor (PFM) is multi-functional Dynamic System Monitor which fully integrates with DIgSILENT PowerFactory software. The PFM features grid and plant monitoring, fault recording, grid characteristics analysis by offering easy access to recorded data, analysis of trends, verification of system upset responses and test results.