Showing results: 166 - 180 of 339 items found.
-
Megger Group Ltd.
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
Megger Group Ltd.
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
Ajinkya Electronic Systems
We provide ECOS, Electrical Vehicle Checkout Systems. VCTS2000 is for testing electrical circuitry in a vehicle. A vehicle typically has on an average around 25 circuits which need to be tested. VCTS2000 helps in testing these circuits by automatically logging the current and voltage data and providing the test results so that the vehicle testing process is faster.
-
Circuit Check, Inc.
Flash programming stations allow you to offload flash programming from functional test systems, increasing test throughput while improving capital utilization. Circuit Check flash programmer fixtures support multiple programmer types and multiple I/O configurations.
-
PeakTech Prüf- und Messtechnik GmbH
A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
I-Stop -
Trilithic Inc.
The I-Stop Reverse Test Probe is a test accessory designed for use with most signal level meters and with the Trilithic 9580 Return Maintenance System. Screw the probe into a distribution tap's unused KS port and a spring-loaded "stinger" connects a 20 dB resistive test point circuit to the hardline.
-
Vogelsang & Benning
Series test bench with high testing depth for electric machines in hybrid drive concepts*Single or multi-chamber systems to optimize the cycle time*Testing the no-load and load characteristics*Motor and regenerative test*Short circuit measurement*Noise measurement (NVH)*Temperature measurement
-
Pro-Check 725 -
LITE-CHECK LLC.
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault. Lite-Check’s patented active diagnostic system takes the guesswork out of identifying trailer light and electrical problems. The Pro-Check commercial trailer light tester with electrical circuit diagnostics, not only identifies faults, but the specific circuit the fault is on. Faults are identified as “Open Circuit”, “Open Ground”, “Short” (w/all circuits identified), or “Chassis Ground”. Audible alarms alert technicians to found electrical faults.
-
IES Systems, Inc.
IES Systems is a turnkey test systems solution provider with 10 years of proven experience in printed circuit board testing solutions. Our experienced engineers design electro/mechanical solutions to interface between your product and our custom designed test instrumentation. We provide a complete solution to your PC board testing needs.
-
SYSTEM 8 (BFL) -
ABI Electronics Ltd
The SYSTEM 8 Board Fault Locator provides the user with the ability to functionally test all common digital ICs in and out-of-circuit. A combination of industry recognised test techniques provides a high level of fault coverage. Additional tools are provided by the SYSTEM 8 Premier software to further enhance the unit\'s wide range of applications.
-
TC.ACS -
Regatron AG
The increasing number of alternative power sources like solar, wind driven or biological energy systems call for consistent and well demanding regulations for energy feed into the utility grid. Manufacturers of such systems have to test and to prove the compliance of their equipment. Grid simulators form an electronic equivalent circuit for the grid, but allow to vary all relevant parameters in order to test the behaviour and response of the equipment under test.
-
TRIO-TECH International
The COBIS-II Series Burn-in System is designed to test the latest high frequency integrated circuits (ICs) and combines a large capacity oven with well proven Accutron FlexBID™ dynamic driver technology. This system is engineered for productive dynamic device testing and reliable monitoring.
-
NI
Whether you are performing high-accuracy, low-speed measurements on a dozen test points or high-channel, high-frequency characterizations of integrated circuits, National Instruments delivers a flexible, modular switching solution based on PXI or SCXI to help you maximize equipment reuse, test throughput, and system scalability.
-
TCT-2690PRO -
Tenma
LAN/length cable tester quickly and accurately tests network, telecommunication, cable and security systems for a variety of issues. Tests for open or short circuits, jumpers, cross or split pairs, continuity and wiring of cable patterns, cable identification and length measurement using included remote ID.
-
TE6-0718 -
Hangzhou Tonny Electric & Tools Co., Ltd.
*For use on 6V, 12V and 24V DC systems*Tests high and low voltages on all vehicle circuits, including computerized engine and body controls*Dual color LED indicates red for power and green for ground