Filter Results By:
Products
Applications
Manufacturers
-
product
PXI Breadboard Module, 1-Slot, 96-Pin Micro-D
40-220A-001
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
Economy Mechanical Calibration Kit, DC To 3 GHz, Type-N, 75 Ohm
85036E
The Keysight 85036E economy calibration kit contains precision 75 ohm type-N male fixed termination and a one-piece 75 ohm type-N open/short circuit. These standards are used to calibrate Keysight network analyzers for measurement of devices with 75 ohm type-N connectors. The kit is specified from dc to 3 GHz.
-
product
Current Transducer
IN 1000-S
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation between the primary and the secondary circuit. 1000 A nominal, 3 ppm linearity over the temp. range, Very low offset drift 19.5 ppm, low noise 34 ppm peak-peak, -40 to +85°C, one compact package.
-
product
16-Channel VME Analog/Thermocouple Input Module
V450
The V450 is a 16-channel 24-bit VME isolated analog-to-digital converter module which can acquire a wide range of DC voltages, including thermocouple readings with automatic cold junction compensation. Each channel is independently isolated with it's own A/D converter, signal conditioning, input protection circuits, and test relay.
-
product
Calibration & Demag.
Model 8515-D
The Model 8515-D is a medium-energy, high voltage, and capacitor discharge type ringing demagnetizer capable of desaturating Ceramic and Rare Earth magnetic materials. The Model 8515-D is easily adapted to a wide range of production and laboratory demagnetizing requirements. A modern solid-state electronic control circuit, coupled with a rugged, heavy-duty discharge SCR and fixture, make this demagnetizer a highly reliable, low maintenance unit. The electronic voltage control circuit prevents the Model 8515-D from being discharged before the preset energy level has been reached, avoiding incomplete magnet desaturation. An easy to read front panel meter monitors the capacitor voltage. The energy storage level can be easily changed in the field. Integral electrical interlock and fail-safe circuitry provide a high degree of operator safety.
-
product
Thermal Conductivity Measuring Device
TCM1001
In recent years, there has been a demand for small and thin electronic products such as mobile devices, and printed circuit boards are shifting to thin, multi-layered, and even modularized printed circuit boards. effect of bonding materials, that is, the ability to easily conduct heat, is emphasized, and testing equipment that evaluates thermal conductivity is required .As a business of our company, we have mainly manufactured and sold test equipment for solder wettability tests and solder bonding strength, but there was a need to urgently develop next-generation bonding material test equipment to replace these. Under these circumstances, we received a request from an academic research facility to manufacture a device that can measure the thermal conductivity of conductive adhesives under research and development, and we were able to obtain an opportunity to develop the device. We proceeded with the development based on these requirements .
-
product
Battery Charger-Analyzer for small battery systems (up to 10A-Hr)
24-400xg
The 24-400XG is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation of Constant Current Charge (dual and single rate), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge (analysis), Resistance Discharge (analysis) and Full Discharge (deep cycle), the 24-400XG can satisfy the requirements of most small (0 to 10 A-hr) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit (no load) and Overvoltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights inform of the status of the operation.
-
product
Intelligent Battery Charger-Analyzer for Large Battery Systems
SuperMasterCharger
The SuperMasterCharger is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMasterCharger can satisfy the requirements of most large ( 10 A-hr to 100 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
product
Intelligent Battery Charger-Analyzer for Battery Systems
SuperMini
The SuperMini is an instrument designed to charge, trickle charge and analyze ( discharge ) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries. With its multiple modes of operation: Constant Current Charge ( dual and single rate ), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge ( analysis ), Resistance Discharge ( analysis ) and Full Discharge ( deep cycle ). The SuperMini can satisfy the requirements of most ( Up to 40 A-hr ) rechargeable battery systems. The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit ( no load ) and Over-voltage conditions. Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights display the status of the operation.
-
product
Circbord
8008
VECTOR Electronics and Technology, Inc.
Pad-Per-Hole & Planes 2 Sides. Unique circuit pattern features full voltage & ground planeson both sides with isolated plated-thru holes. 0.080” diameter, isolated solder pad around holes oncomponent side. Plane surfaces solder-coated for user convenience. SMD cap positions for discrete decoupling capacitors.
-
product
Gas Online Analyzer
OMA-100
OMA-100 gas online analyzer is a new generation of online gas analyzers which was independently developed based on the world's leading non-dispersive infrared gas analysis technology. It adopts a half-air chamber gas circuit design, with higher measurement accuracy, lower drift, and less influence from external interference (temperature fluctuati
-
product
High Impedance Transformers
Osborne high impedance transformers are used to step-up, step-down and isolate voltages in single phase and three phase circuits. A properly designed high impedance transformer can be used an an equivalent to an isolation transformer connected in series with an inductor. The high impedance characteristic may be employed as a current limiting feature in both the primary and secondary circuity.
-
product
International Socket Strip-Rack Mount
85010113
This International Socket Strip includes seven international test sockets. It includes one unterminated power cord. For 220-240 circuit: Continental Europe (CEE 7) 16A. Denmark 16A. Italy 10A. India (old British BS 546) 15A. Switzerland 10A. Australia/New Zealand 10A. United Kingdom/Ireland 13A.
-
product
PROBE MICROPHONE ICP
377B26
Open Circuit Sensitivity (at 250 Hz)Frequency Range (+2.2/-4.9 dB)2 to 20000 HzLower Limiting Frequency (-3 dB)Inherent Noise<45 dB(A) re 20 Pa Dynamic Range(3% Distortion Limit)EnvironmentalTemperature Range (Operating)-40 to +158 F-40 to +70 C[5]
-
product
Quartz Crystals
Quartz crystal resonators are used in a wide range of electronic applications that require timing devices. The quality of the quartz crystal blank is critical to the performance of quartz crystal units and the high Q factor of quartz means that tight stabilities can be achieved; this is key to ensuring microprocessor timing circuits work correctly within customer’s designs.
-
product
Terminal Equipment Simulator
AI-5620
The AI-5620 simulates a single port two wire analog TE (Terminal Equipment) or CPE (Customer Premise Equipment) device. It is designed to measure and analyze signals generated by a CO (central office) line card, VoIP terminal adapter FXS port, or any device utilizing a SLIC (subscriber line interface circuit).
-
product
Carbon Sensor Conductivity Meter High-Concentration
HE-960HC
FPD manufacturing processesThe HE-960HC measures conductivity, which forms the basis for parameters in chemical and waste water management. Its dual calculation circuits and software, combined with carbon sensors, enable measurements ranging without switching. The HE-960HC can be used as a process concentration meter, and also to monitor changes in the concentration of specified chemicals.
-
product
PXI Prototyping and Breadboard Modules
The breadboard modules with digital I/O (the 40-220A series) allow the user to construct their own circuit in situations where a PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include creating custom circuitry that can be housed on a 3U board or to build special “one-off” switching modules.
-
product
Line Impedance Stabilization Networks
LISN
LISN stands for 'Line Impedance Stabilization Network'. Com-Power offers a line of LISNs developed for conducted emission testing according to the most commonly adopted EMC specifications like CISPR, FCC, ISO, EN, RTCA DO-160 and MIL-STD 461D. The LISN circuit is designed and constructed to meet the performance criteria given by these standards.
-
product
Audio Cable Testers
AudioJog Pro 5
ALL new Audio cable tester with SINGLE & DOUBLE ended testing. There are 2 rows of 6 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found.
-
product
PCB Failure Analysis: Identification and Testing of Defects
From cheap toys and smartphones to sophisticated computers and radar detector systems, printed circuit boards (PCB) are critical components for today’s electronic and industrial technology. Almost every electronic device has one of these self-contained modules of complex interconnected electronic components, which include resistors, capacitors, transistors, diodes and fuses.
-
product
Plastic Fabrications Testing Equipment
PD and PHD Pinhole/Holiday Detectors have an alarm circuit to alert the operator when a fault has been located and the required test voltage can be set on the unit's meter. Spark Testers provide an inexpensive means of testing but have no output voltage meter or audible alarm. However, they can test joints even if the backing is not connected.
-
product
Pick and Place Test Handler
Delta Eclipse
Eclipse delivers scalable performance for testing a wide range of semiconductors, from analog ICs to high-performance CPUs and mobile processors. The Eclipse is a high-speed pick-and-place handler designed to test up to 16 Integrated Circuits (ICs) in parallel, at temperatures from -45°C to +155°C*, with throughput up to 13,000 UPH.
-
product
Power device test system
This system is suitable for DC testing of IGBT, IGBT module (1in1~7in1). Built-in hi-current switching relay circuit inside test head, it is capable ofDC testing from device itself to module. Highly accurate repeatability testing is available by high speed rise time which is suppressed its heat in hi-current
-
product
Flying Probe Test Programming & Testing Services
Zero Defects International LLC
ZDI utilizes a Seica flying probe tester in order to provide test program development and testing services to customers in Silicon Valley and throughout North America. This is a very cost-effective solution for printed circuit assembly manufacturers who do not have in-house equipment of their own but have customers who require test services.
-
product
DC Detector
This sensor can be used to troubleshoot any DC circuit with voltage ranging from 6-50 volts DC. It features an audio and visual alert and a sharp, rust-proof, stainless steel tip that works great for penetrating insulated wires. This sensor also features an extended ground lead with an extra-large alligator clip to ensure a good connection.
-
product
IPC Testing
IPC was founded in 1957 as the Institute for Printed Circuits. Today, it is a global trade association representing the electronics industry with a focus on design, PCB manufacturing and electronics assembly. IPC has over 3700 members, including Aerojet Rocketdyne, Rockwell Collins, Lockheed Martin Mission Systems & Training, and Parker Hannifin Electronic Controls.
-
product
Signal Injectors
Ideal high performance, low noise compliment to your Circuit Sleuth Frequency Response Analyzer. An injection transformer is used to couple an excitation signal from a frequency source into the feedback loop of a control system. This allows loop gain and phase vs. frequency to be measured, with the loop closed, thus characterizing the stability of the system.
-
product
18V/3A Single Output DC Power Supply
Extech 382202
Extech Instruments Corporation
The 382202 is a DC power supply which provides an adjustable 0 to 30 Volts and 0 to 1 Amp output. Features dual backlit LCD display for current and voltage, short circuit and overload protection. Operates from 120VAC ±10%/60Hz power source. Banana plug outputs. Complete with power cord.
-
product
Blocking Capacitor, 0.045 to 26.5 GHz
11742A
The Keysight 11742A blocking capacitor blocks dc signals below 45 MHz and passes signals up to 26.5 GHz. Ideal for use with high-frequency oscilloscopes or in biased microwave circuits, the Keysight 11742A will suppress low frequency signals that can damage expensive measuring equipment or affect the accuracy of your RF and microwave measurements.