Filter Results By:
Products
Applications
Manufacturers
-
product
Impedance Analyzer, 20 Hz to 10/20/30/50/120 MHz
E4990A
The E4990A Impedance Analyzer has a frequency range of 20 Hz to 120 MHz. The E4990A provides an industry best 0.045% (typical) basic accuracy over a wide impedance range, with a 40 V built-in DC bias source. The equivalent circuit analysis function supports seven different multi-parameter models and helps you to simulate your own equivalent parameter values of components.
-
product
Pressure Type Water Level Gauge
HR8003
HighReach Measuring & Controlling System Co.,Ltd
HR8003 high-precision pressure water level gauge is a hydrological instrument used for water level and water temperature measurement. It is developed through years of production technology and uses advanced mixed signal processing technology to overcome the shortcomings of traditional analog circuit modules. Full-scale digital Linear correction, full temperature zone digital temperature error compensation; compensation parameters are stored in non-volatile memory.
-
product
Wet Sponge Pinhole Detection
Wet Sponge Technique: A low voltage is applied to a moist sponge. When the sponge moves over a coating flaw, liquid penetrates to the substrate and completes an electrical circuit, setting off the alarm. The wet sponge technique is suitable for measuring insulating coatings less than 500μm (20mils) on conductive substrates, and is ideal for powder coatings and other coatings where the user does not wish to damage the coating.
-
product
Sand Test Chambers
Labodam sand and dust test chambers are corrosion resistant equipment that tests the stability, quality, reactivity, and characterists of products against the sand and dust exposed environmental conditions. These test chambers are carefully designed as per the CE and ISO standards and provide rpotection against current leakage, overload, over-current, short circuit, over temperature, motor overheating, and over pressure for safe and precise results.
-
product
IR Carbon and Sulphur Analyzer
LD-LCSA-A11
IR Carbon and Sulphur Analyzer LCSA–A11 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 25 to 60 seconds and oxygen purity of 99.5 %, the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 24-bit sampling improves sensitivity and accuracy.
-
product
IR Carbon and Sulphur Analyzer
LD-LCSA-A10
IR Carbon and Sulphur Analyzer LD-LCSA-A10 is a unit for determination of sulphur and carbon equipped with two treatment units including a high frequency induction burner and flexible temperature settings with automatic control. With an analysis time of 20 to 100 seconds and a sensitivity of 0.1 ppm the multi-shielded isolation circuit prevents the machine for high frequency interference. High speed 24-bit sampling improves sensitivity and accuracy.
-
product
Current Probe
PA-699
*High sensitivity: 1mA, High frequency: 1.5MHz. They are all 10 multiple calculation. Calculation is not making mistakes.*Max measuring current: +/- 40A DC / 80 Ap-p*Max sensitivity: ≧1mA*Bandwidth: DC ~ 1.5 MHz*Rising Time: 0.23 uS*Overload indicator*1V/A, 0.1V/A 2 ranges selectors*Input power switching (priority circuit) and battery available*Dispatching design, high durability
-
product
Gaussmeter
DX-105
DX-105 Gaussmeter is a desktop gaussmeter. Which is based on the latest progress of the Hall Effect magnetic field measuring instrument.Adapt the high stability constant current source circuit technology to design and manufacture. Test probe adapts imported GaAs linear Hall-chip, the difference between any two probes is small, which can be replaced directly when it is damaged. DX-105 Gaussmeter is an ideal DC magnetic field test instrument.
-
product
High-Current Arc Ignition
(HAI) UL 746A
High-Current Arc Ignition (HAI) performance is expressed as the number of arc rupture exposures (standardized to the electrode type and shape and electric circuit) that are necessary to ignite a material when they are applied at a standard rate on the surface of the material. The number of arc rupture exposures necessary to ignite a material when they are applied at a standard rate on the surface of the material. Performance Level Categories (PLC) were introduced to avoid excessive implied precision and bias.
-
product
High Node Count In-Circuit Test Fixtures
HNC Test Fixture
Circuit Check continues to be a leading edge provider of custom engineered test solutions with our new Keysight i3070 HNC test fixture. Working with Keysight Technologies during the development of their HNC adapter in 2011, we were the first test fixture provider to offer customers with a solution to test large node count boards. High node count test fixtures can handle greater than 10,000 probes.
-
product
Multi-Decoder
CTCSS sub-audible tone decoder reveals repeater access tones DCS Digital-Coded Squelch decoding (requires receiver with discriminator or demodulator (unfiltered) output) DTMF "Touch-Tone™" decoder / logger Improved 2-tone decoding captures "stacked" pages Built-in Log Viewer / Player External serial port control to operate relay or PTT circuit Fully supports Windows XP, Vista / 7, 8, 10
-
product
Operational Amplifiers
Op Amps
For designs requiring operational amplifiers (op amps), Analog Devices' portfolio of high speed op amps and precision op amps provides a broad choice of products that deliver unmatched performance. Explore op amps by parameters, and find expert system-level advice on design problems with our amplifier reference designs (Circuits from the Lab®), design tools, selection guides, calculators, and SPICE models.
-
product
Precision Condenser Microphone
2575
Performance:Nominal Microphone Diameter1"1" Frequency Response: Characteristic (at 0 incidence) Random IncidenceRandom Incidence Open Circuit Sensitivity: 45 mV/Pa Resonant Frequency (90 Phase Shift)8000 Hz8000 Hz[1] Inherent Noise<10 dB(A) re 20 Pa<10 dBTemperature Range (Operating)TBD FTBD C Humidity Coefficient of Sensitivity (0 to 95%, non-condensing)0.001 dB/%RH
-
product
Single-Ended Amplifiers
Op-Amp
For designs requiring single-ended amplifiers (op amps), Analog Devices' portfolio of high speed op amps and precision op amps provides a broad choice of products that deliver unmatched performance. Explore op amps by parameters, and find expert system-level advice on design problems with our amplifier reference designs (Circuits from the Lab®), design tools, selection guides, calculators, and SPICE models.
-
product
Single Sided PCB
Amitron produces prototype, midrange and high volume Single Sided circuit boards, with a copper thickness from one to twenty ounces. Operating temperatures range from 130 C to 230 C. Single sided boards are available with surface finishes including Organic surface protectant (OSP), Immersion Silver, Tin, and Gold plating along with both leaded or lead-free Hot Air Solder Level (HASL).
-
product
Surface Mount Temperature Sensor
SCS
The Series SCS Low Cost Current Switches are ideal for monitoring whether fans, pumps, or motors are operating. The current flowing through the core of the device powers the circuit without an external power supply. All models have a built in solid state output and are easy to install. Optional LED's and 10 Amp relay modules are available. The Series SCS is available in both Split and Solid Core configurations
-
product
Thermal Load Boards
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
product
Thermometers With Switch Contacts
WIKA Alexander Wiegand SE & Co. KG
Wherever the process temperature has to be indicated locally and, at the same time, limit values must be monitored, thermometers with switch contacts find their application. The switch contacts make or break the circuit dependent upon the pointer position of the indicating measuring instrument. If the reading is significantly above or below a set value, they trigger an alarm, hence also the term “alarm contact”. The instruments are also suitable for starting, stopping or switching processes.
-
product
Transformer Test Panel/ Setup
This is a common test panel for distribution/ power transformers of different specifications. The user can perform most of the factory tests, as per the relevant IS standard for the transformers. The panel consists of power analyser, meters for high voltage test, meters for induced voltage test etc, control for all the tests, protection and interlock circuits so that a single panel can be used to conduct a number of tests using only one dimmerstat and the associated devices
-
product
Wall Mount Power Supplies
AC-DC Single Output
Although small in size, these mini-modules offer high performance at modest prices. All models, with series regulated outputs ranging from 1 to 75 volts and as high as 2.5 amps, may be mounted in an area only 3.5" x 2.5". Terminal strip input/output connections eliminate all need for sockets or soldering. Short circuit protection, encapsulated construction, and conservative design assure long term reliability.
-
product
14 Bit ADC Card
FMCADC100M14B4CHA
Sundance Multiprocessor Technology Ltd.
The FmcAdc100M14b4cha is a 4 channel 100MSPS 14 bit ADC card in FMC (FPGA Mezzanine Card) format. By default it uses only signals from the LPC rows of the HPC connector that is mounted. The gain can be set by software in three steps: +/-50mV, +/-0.5V, +/-5V. An advanced offset circuit is used in the front-end design of the ADC board, and allows a voltage shift in the range of +/- 5V that is independent on the chosen gain range.
-
product
150MHz Isolated Oscilloscope
M774
The M774 is a dual channel USB oscilloscope compatible with USB 2.0 and USB 1.1 interface. The computer is isolated up to 500Vp from the measuring circuits of the oscilloscope. The ease of installation and connection to computer makes M774 extremely portable. The device is connected to computer using standard USB 2.0 cable and is powered directly from computer. The maximum power consumption of 2.35W makes this instrument highly usable with battery-powered notebooks.
-
product
Alchitry Au+ FPGA Development Board (Xilinx Artix 7)
The Alchitry Au+ is the "gold" standard for FPGA development boards and it's possibly one of the strongest boards of its type on the market. The Au+ substitutes a more robust & scalable FPGA chip (Xilinx XC7A100T) that allows for more complex application circuits. The number of Configurable logic blocks (LABs/CLBs), Logic Elements, and total RAM bits are all nearly 3x that of the standard Au; see "Features" for more details.
-
product
Attenuators
Shenzhen Tojoin Communication Technology Co., Ltd.
Attenuators are used in a wide variety of applications and can satisfy almost any requirement where a reduction in power is needed. Attenuators are used to extend the dynamic range of devices such as power meters and amplifiers, reduce signal levels to detectors, match circuits and are used daily in lab applications to aid in product design. Attenuators are also used to balance out transmission lines that otherwise would have unequal signal levels.
-
product
PCB Test Fixtures
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
product
Analysis via Scanning Electron Microscopy / Energy Dispersive X-Ray Spectroscopy (SEM/EDS)
The use of Scanning Electron Microscopy / Energy Dispersive X-Ray Spectroscopy (SEM/EDS) in the analysis of failure related issues of printed circuit boards (PCBs), assemblies (PCAs), and electronic components (BGA, capacitors, resistors, inductors, connectors, diodes, oscillators, transformers, IC, etc.) is a well-established and accepted protocol. As opposed to or simply in addition to normal optical microscopy, SEM/EDS allows for the “inspection” of areas of interest in a much more informative way.
-
product
PCIe Gen3 High speed, compact Camera for Testing
CB013MG-LX-X8G3
High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
product
Microelectronics Test & Engineering Services
EAG's Microelectronics Test and Engineering lab network provides semiconductor and electronics design firms worldwide with test, debug, and early engineering support to help you with new product introduction. We actively service a broad range of semiconductor and electronics companies worldwide. Services include ATE testing, Reliability testing and qualification, ESD testing, Failure Analysis, FIB Circuit Edit and Debug. for both ICs and systems
-
product
PCIe Gen3 High Speed, Compact Camera for Testing
CB013CG-LX-X8G3
High speed, compact, fast camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
-
product
PCIe Gen3 4K Compact, High Speed Camera for Testing
CB120MG-CM-X8G3
4K, compact, high speed camera for: Vehicle Impact, Airbag Deployment and Safety Restraints Testing, Digital Image Correlation (DIC), Projectile, Explosives, Ballistics, Combustion and Missile Launch Tracking, Fluid and Flow Visualization, Sports Broadcasting, Commercial Film, Television and Studio Production, Fluidics and Particle Image Velocimetry (PIV), Flat panel inspection (FPD), printed circuit board (PCB) examination and more.
