Showing results: 1561 - 1575 of 2577 items found.
-
Osborne Transformer Corp.
Osborne Potential Transformers (PT’s) are used to reduce higher system voltages to lower values that are appropriate for instrumentation and/or protection circuits. They have been designed to meet specified current ratios, and burden impedance at a specified transformation error. One area of unique Osborne expertise is in designing for phase shift when potential transformers are to be used for power measuring applications.
-
IOScope -
Faber Acoustical, LLC
With IOScope, measure loudspeaker impedance, frequency response, and sensitivity. Measure a room impulse response. Tune a large sound reinforcement system, time-align a set of surround sound speakers, or optimize your home stereo. Determine the actual cutoff frequencies of your latest speaker crossover circuit, or teach your students the fundamentals of Fourier analysis of dynamic systems.
-
DPS -
KEYCOM Corp
EYCOM develops and manufactures highly accurate and dependable measurement systems for permittivity, dielectric loss tangent, or permeability by leveraging its accumulated experience and expertise over a long period of time. Capitalizing on such experience and expertise, KEYCOM is committed to developing customized solutions for wide range of specific applications such as flexible circuit board, semiconductor, thin film, millimeter wave and microwave frequency board,
-
Shortsniffer -
Testec, LLC
The ShortSniffer Voltage probe evolved as an effective troubleshooting tool for a small set of problems, but has been quite useful in a variety of non-obvious circuit design, development, troubleshooting, and optimization efforts. Let me tell you about the characteristics of the system and of a few of the successes with the non-traditional uses, and maybe you will find this tool useful in your design or troubleshooting efforts.
-
200M -
Laxtronics Instruments & Controls Pvt. Ltd
Digital insulation tester Model No: DIT200M is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage from 1 to 30 Volts DC, its short circuit current is less than 100uA. The instrument can measure Resistance from 1 Meg Ohm to 1000 Meg Ohms.
-
Phoenix Contact GmbH & Co. KG
Signal conditioners and measuring transducers ensure interference-free signal transmission in measurement and control technology. From highly compact 6 mm signal conditioners and measuring transducers through signal conditioners with functional safety to signal isolators for intrinsically safe circuits in the Ex area: our signal conditioners and measuring transducers ensure interference-free signal transmission in MCR technology.
-
Microchip Technology Inc.
Enable your 5G, aerospace, defense, test and measurement or industrial RF wireless applications with our portfolio of RF and microwave devices. These include high reliability RF diodes, Gallium Nitride (GaN) and Gallium Arsenide (GaAs) Monolithic Microwave Integrated Circuit (MMIC) amplifiers, frequency translation and power transistor devices, switches, attenuators, varactors, filters and more.
-
ARC Technology Solutions
ARC has worked with the DoD/military agencies and the FAA to help service and repair critical products in the national air system and various line replaceable units (LRUs) that may contain multiple circuit cards. With a skilled team of engineers and service technicians that can troubleshoot, reverse engineer, and help in finding components for damaged and obsolete parts, ARC is the right depot partner.
-
GOLDSUN Electronics Co., Ltd.
The Tester can check UTP and STP Cat 5E,6,6A and Coaxial Cable. It can ldentify and locate the distance of a open or Short Circuit. With the Multifunction Tester you can determine the Continuity and Wiring of the Cable Pattern. Comes with the Low Battery Indicator. It uses TDR ( Time Domain Reflectometer ) to measure the length and distance of the cable. LCD Backlight Display.There are 8 Remote ID available.
-
Morris Products Inc.
Tests & troubleshoots voice communication for open circuits, shorts, miswires, reversals, and split pairsSHIELD detection tests a cable’s shield integrityEasy to read fault display and high speed testingDebug mode for detailed fault identification resultsNetworking Cable Tester has auto sleep mode and power off switch to decrease power consumptionBattery low LED indicator
-
Megger Group Ltd.
Megger loop testers offer both traditional measuring techniques and state of the art “non-RCD Tripping” technology. Use these products to determine the prospective earth fault current, which is the maximum current able to flow in a phase-earth fault in an installation, and also to indicate the prospective short circuit current which is the maximum current able to flow in the event of a phase-neutral fault.
-
Megger Group Ltd.
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
1120 ER -
Standard Electric Works Co., Ltd
● Waterproof: IP54● Capable of measuring earth resistance and earth voltage● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test● The test leads are supplied as standard accessories for simplified two-wire measuring system● 0Ω adjustment● Battery operated● Data hold function● Low battery indication
-
11867A -
Keysight Technologies
11867A RF limiter can be used to protect the input circuits of spectrum analyzers, counters, amplifiers, and other instruments from high power levels with minimal effect on measurement performance. This limiter (10 Hzto 1800 MHz) reflects signals up to 10 watts average power and 100 watts peak power. Insertion loss is less than 0.75 dB.
-
Columbia Elektronik AB
Testing is more than just finding defects on Printed Circuit Boards. It is also about how to predict defects before they occur. A true economy can only be achieved when you see testing as an integrated part of manufacturing. To achieve this we provide Advanced Diagnostic Tools and Electronic Manufacturing Systems (EMS) that integrate testing with design, manufacturing, and repair.