Showing results: 976 - 990 of 2617 items found.
-
MDLA-100 -
MULTI MEASURING INSTRUMENTS Co., Ltd.
This DC Leakage Current Monitor constantly observes leakage current of DC circuit like as PV generation system, etc. and lights up the warning lamp with signal output, when the leakage current exceeds the setting value.
-
MHR-600 -
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Measuring and recording the average current values & power flow directions in the setting interval.・Easy to use, as an indirect hot-line work tool.・Memorized data can be outputted to USB memoryafter measurement.・For 6.6KV circuit, protection level IP64.
-
Leuze electronic GmbH + Co. KG
With the MSI safety relays, individual safety sensors can be integrated quickly and easily into the safety circuit of machines and systems. The MSI contact extensions are used both as an output extension for OSSDs and for contact multiplication for evaluation units and safety controls.
-
LCR01D -
MINPU TECHNOLOGY CO., LTD.
*Basic accuracy:0.3%*Test Voltage: 0.5Vrms* Circuit Calibration:Open/Short*Test Frequency:10MHz,5MHz,1MHz,100KHz,10KHz,1KHz*Measure Parameters Include:Z, Lp, Ls, Cp, Cs, ESR, D, Q, θ
-
MegiQ BV
The unbalanced interface of a VNA is not very well suited for measuring balanced circuits like antennas, transmission lines or chip impedances. In fact it is nearly impossible to get a decent calibration on a balanced 2-port measurement using coax cables.
-
PinPoint II R -
DiagnoSYS Systems Ltd
The Diagnosys PinPoint IIR provides industry-leading capability for the test and fault finding of the most challenging PCB (or CCAs). Allowing you to select and apply different test techniques on a single circuit, you can ensure maximum fault coverage.
-
Applied Relay Testing Ltd.
General purpose calibration/diagnostic tool.Built in precision resistors.Simple manual contact/routing/resistor selection.4mm terminal posts on key device connections.In line mode to aid fixture wiring/DUT debugging.Comprehensive documentation including circuit schematics.Connecting cables.
-
National Technical Systems
Conductive Anodic Filament (CAF) testing helps to determine the reliability of a printed circuit board (PCB) laminate material or a finished product. With conductor spacing and overall part sizes getting smaller and smaller, the necessity for this test is increasing.
-
HW Test
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
CCM1095 and CCM2096 -
Teledyne RF & Microwave
The CCM1095 and CCM2096 are power amplifiers that use current efficient Silicon Carbide output semi-conductors to achieve +35 to +38 dBm output power. An internal sequencing circuit is included to provide for safe operation of the output power device.
-
LCI™ -
ndb Technologies Inc.
The LCI™ system is intended for energized cable identification on secondary and primary circuits. This innovative solution features a dual frequency technique that eliminates false identifications. The LCI™ is designed to be easy to use, safe for the user and cost-effective.
-
Pro-Check 720 -
LITE-CHECK LLC.
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault.
-
WR14 -
Raytech AG
Raytech's Digital Winding Resistance meter WR14 is the battery powered version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy measurement of very low resistance of any inductive loads.
-
ZET 7010 -
ZETLAB Company
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
Acroname, Inc
LEAN AND MINIATURIZED PRODUCTION TESTING: With its ultra-small footprint, the MTM-Load-1 is engineered for load-testing of battery chargers, amplifiers, USB power outputs, and motor driver circuits. Ideal for functional testing in production or validation test environments.