Showing results: 1066 - 1080 of 2577 items found.
-
QRE1113 (Digital) -
SparkFun Electronics
This version of the QRE1113 breakout board features a digital output, using a capacitor discharge circuit to measure the amount of reflection. This tiny board is perfect for line sensing when only digital I/O is available, and can be used in both 3.3V and 5V systems.
-
CYHCT-L20K -
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-L20K is based on open loop principle and designed with a high galvanic isolationbetween primary conductor and secondary circuit. It can be used for measurement of DC current, DCpulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Tripp Lite
A surge protector is an appliance or device intended to protect electrical devices from voltage spikes in alternating current (AC) circuits. A voltage spike is a transient event, typically lasting 1 to 30 microseconds, that may reach over 1,000 volts
-
Kryoz Technologies BV
The CryoLab is designed to perform rapid material or circuit characterization measurements from room temperature down to cryogenics in a fully automated manner. Doing measurements doesn’t require any experience or know-how on cryogenics, vacuum technology or thermodynamics from the user.
-
Non-Contact & Socket -
Amprobe Test Tools
Use Amprobe non-contact volt probes to safely check circuit breakers, wall sockets and fuses for voltage presence with portable, economical tools. For sockets, choose an Amprobe socket tester, which can confirm whether GFCI breakers are properly wired.
-
T5-1000 -
Fluke Corporation
Measure current up to 100 A without breaking the circuit with OpenJaw™ design. The T5-1000 Electrical Tester is a versatile troubleshooting tool to carry to every job site. Use it to check voltage, continuity, and current–all with one compact tool.
-
MSAT -
ARC Technology Solutions
Whether you are testing radar systems for the Department of Defense (DoD), or the next actuator circuit card for aircraft landing systems, ARC’s Mixed Signal Automated Tester (MSAT) offers flexible automated testing capabilities for nearly every budget.
-
11930A -
Keysight Technologies
The Keysight 11930A limiter provides input protection for a variety of RF and microwave instrumentation. For example, the input circuits of network analyzers may be protected for inputs up to 6 watts peak or 3 watts average power using the Keysight 11930A.
-
Di-Log
Digital multimeters (DMM’s) are great for measuring parameters on electrical circuits. Rather than having separate instruments, why not choose one of our handheld digital multimeters and easily measure AC/DC voltages, current, resistance and other electrical parameters.
-
Environment Associates Inc.
Fungus can cause products to malfunction during operation and can grow on just about anything if the conditions are right. It will break down certain plastics, rubbers, paints and gaskets if it attaches itself and is left to grow. Fungus is known to short out electronic circuits.
-
040-647 -
ELMA Electronic, Inc.
The Fan Controller (FanCon) is a platform independent system monitoring unit which monitors and if applicable controls the parameters, such as temperature and fan rotation speed, of a basic system. The centrepiece is an 8-bit microcontroller with an integrated 10-bit A/D converter and a corresponding peripheral circuit.
-
040-645 -
ELMA Electronic, Inc.
The Fan Controller (FanCon) is a platform independent system monitoring unit which monitors and if applicable controls the parameters, such as temperature and fan rotation speed, of a basic system. The centrepiece is an 8-bit microcontroller with an integrated 10-bit A/D converter and a corresponding peripheral circuit.
-
TRF -
TOEI INDUSTRY CO, LTD.
This is the equipment being able to measure direct current magnetization property of wide-ranging magnetic materials from soft magnetic materials to high performance permanent magnet with magnetic flux meter based on M integral closed magnetic circuit system.
-
AEM-DRA -
Chuan Sheng Electronics Co., Ltd.
The AEM-DRA series has 2 independent and isolated main circuit inputs , can use for different power system.Up to 24 single phase or 8 three-phase circuits, programmable from push buttons with LCM display panel, or using Adtek program software through RS485 communication port.Hardware standard built in a RS485 Modbus communication port , 2 Digital inputs, 4 Relay outputs, LCM and 2 MB flash for data-logging.Optional second communication port for Ethernet, ProfiBus ,LonWorks ,BACnet and Zigbee solutions.Din rail mounting , compact and easy installation, programming through computer and push buttons easy to use.
-
CAT Advanced Series -
Amperis sl
Description The Advanced CAT Series Analyzers and Timers are stand-alone or PC-controlled digital instruments for circuit breaker status evaluation. Timing channels record arc closing and opening, resistance and auxiliary contacts. The main contact channels can also measure the resistance value of pre-insertion resistors (if present in the breaker). The advanced CAT series records graphs of the opening and closing coil currents and the movements of the moving parts of the high and medium voltage circuit breaker. Test results are printed on the 112 mm (4.4 inch) thermal printer (optional accessory) in tabular and graphical form. The advanced CAT series provides easy selection of different operating modes: