Showing results: 871 - 885 of 1473 items found.
-
Teledyne RF & Microwave
Teledyne’s Bulk Acoustic Wave (BAW) Product Line has been producing BAW delay devices since the early 1960’s. Over the years, Teledyne Microwave Solutions (TMS) has constantly improved BAW technology and is currently the world’s only supplier of microwave bulk acoustic wave delay devices. Markets for BAW devices include instrumentation and radar altimeters and are available in connectorized, pin and surface mount configurations.
-
AMETEK VTI Instruments
The first VXIbus specification was introduced to the test and measurement community in 1987 and was initially developed to provide a card-based instrumentation platform for applications that required high density and high performance. The platform continues to thrive today by leveraging off the original specifications which define the necessary physical (real estate/cooling) and electrical standards for demanding applications and has established itself as the ‘time-tested bus you can trust’ for requirements that must be supported in excess of ten-fifteen years.
-
AMETEK VTI Instruments
The first VXIbus specification was introduced to the test and measurement community in 1987 and was initially developed to provide a card-based instrumentation platform for applications that required high density and high performance. The platform continues to thrive today by leveraging off the original specifications which define the necessary physical (real estate/cooling) and electrical standards for demanding applications and has established itself as the ‘time-tested bus you can trust’ for requirements that must be supported in excess of ten-fifteen years.
-
Advantech Co. Ltd.
MicroATX (uATX) or mATX Industrial Motherboard is only 244 x 244 mm and suited for space/cost sensitive applications where less than 4 slots are required. mATX enables the same high integration of ATX but with a smaller footprint that fills the gap between MiniITX and full size ATX, balancing performance and expansibility. Equipped with LVDS interface, longevity and revision control, MicroATX(uATX) is ideally suited for medical and instrumentation applications.
-
CX-H60L -
Shenzhen Chuangxin Instruments Co., Ltd.
The salt water Spray Tester is used to create and maintain the salt spray (fog) test environment, and test the anti-corrosion quality of the materials surfaces, and is suitable for researching materials, light industry, electronic, instrumentation and other industries etc.
-
HMMC-3028 -
Keysight Technologies
The HMMC-3028 is a DC - 12 GHz divide by eight prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
HMMC-3022 -
Keysight Technologies
The HMMC-3022 is a DC - 12 GHz divide by two prescaler designed for use in high frequency communications, microwave instrumentation, and EW radar systems where low phase-noise PLL control circuitry or broadband frequency translation is required.
-
Pickering Interfaces Ltd.
Mass Interconnect is a mechanical interface that simplifies connection between the power supplies, instruments and switching to the Device Under Test (DUT) in a test environment. In the illustration here, a test receiver is connected to the front of the modular instrumentation, in this case, a PXI chassis.
-
34942A -
Keysight Technologies
The Keysight 34942A RF multiplexer module for the 34980A Multifunction Switch/Measure Unit offers bi-directional switching broadband signals. High channel isolation ensures quality dynamic range measurements with your oscilloscope, spectrum analyzer, or other instrumentation.
-
LXinstruments GmbH
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.
-
LXinstruments GmbH
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.
-
Series MBT-G -
Kepco, Inc.
Kepco's MBT-G series (denoted by suffix "G") are bench-style instrumentation power supplies that offer a choice of control methods including direct entry keypad, slew up/down keys, rotary controls and three communications ports: IEEE 488.2, RS 232 and Kepco's single address, multiple instrument long range serial bus. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
Procter & Chester Measurements Ltd
Radio Telemetry: A transmission of data from a remote source via a radio to a receiving station for recording and analysis. Inductance: A contactless method of supplying power to (in this case) a strain gauge bridge. The signal is then transmitted back to the electronics. Slip Ring: Consists of a conductive band mounted on a shaft and is insulated from it. The wheatstone bridge is connected to the bands (usually four off). Fixed brushes or contacts make contact on to the bands to transfer power to the bridge and signal back to the static instrumentation.
-
Metrix
Seismic signal conditioners are designed to accept an input from (and provide power to) a seismic sensor. They convert the signal to a proportional 4-20mA DC signal that can be used as an input to process control instrumentation such as a PLC or DCS. They provide additional convenience features such as optional displays, BNC connectors for access to the dynamic sensor signal, and bandpass filtering. Metrix offers seismic signal conditioners that can accept either acceleration or velocity sensors, and are available with or without an integral display.
-
Acromag, Inc.
Process transmitters isolate, filter amplify, and convert sensor signals to 4-20mA current or 0-10V voltage signals for interfacing with controllers and other instrumentation. Select from 2-wire loop-powered 4-20mA transmitters, 3-wire DC-powered transmitters, or 4-wire AC/DC-powered transmitters. 3-wire and 4-wire models are available as 4-20mA transmitters or voltage transmitters. DIN-rail and field-mount version are available. Configuration is easy with Windows software, push-buttons, switches, or pots for span/zero settings depending on the series.