Showing results: 3601 - 3615 of 5951 items found.
-
Model 57810 -
Pentek, Inc.
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex Ultrascale FPGAs- Front panel digital I/O can be used as a status and control or data interface- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
100BASE-T1 -
Prodigy Technovations Pvt. Ltd.
100BASE-T1 Automotive Ethernet Protocol Analyzer is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. Automotive Ethernet interface scales up to address current and future needs of in-vehicle bus speed requirement. Need for higher-speed in-vehicle bus is increasing to support feature-rich ADAS and connected vehicle needs. Two-wire full duplex 100BASE-T1 PAM 3 signaling is the choice of interface bus to address these needs
-
Type 131 -
Datum Electronics, Ltd.
The Type Load Cell 131 Amplifier is designed to interface to a full bridge strain gauge based load cell or similar sensor allowing the user to use the data from the load cell in a more efficient and productive way.The Type 131 Load Cell Amplifier is designed to interface to a full bridge strain gauge based load cell or similar sensor. It can be calibrated to provide a 4-20mA output for a fixed load range from the sensor.
-
LXinstruments GmbH
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.The system has a Virginia Panel adapter interface to which various desk adapters can be docked, including automated contacting of the DUTs. A camera for the verification of light emitting diodes on the test object is integrated in the adapter interface.
-
3550 -
TEGAM Inc.
The Model 3550 Programmable Impedance/LCR Meter tests within the extensive frequency range of 42.0 Hz to 5.00 MHz. It measures L, C, R, |Z|, Y, D, Q, R, Phase, G, X, B, V, I, F, in series or parallel modes. With a basic accuracy of 0.10%, the 3550 is designed for a wide variety of automated or manual test applications. RS-232C & I/O interfaces are standard; GPIB or BCD interfaces are optional.
-
APC8621A -
Acromag, Inc.
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system. The half-length card is ideal for use in smaller PC chassis.
-
844 Series -
Leco Corp.
LECO combined our customers' feedback with innovative engineering to develop the CS844, an elemental analyzer designed for wide-range measurement of carbon and sulfur content of primary steels, ores, finished metals, ceramics, and other inorganic materials using the combustion technique. Our exclusive MS Windows®-based software, coupled with a boom-mounted touch interface, gives you complete access to instrument control, analysis settings, diagnostics, reporting, and more—without sacrificing valuable bench space.
-
Epec 3610 -
Epec Oy
Epec 3610 Control Unit is a compact controller containing 22 I/O pins, all of them can be configured as input pins. Epec 3610 has an RS-232 serial port and as an assembly variant, I/O interface that is compatible with the previous Epec 2038 Control Unit. However, Epec 3610 also comes with completely new features like high-side current measurement and an internal 3-axis accelerometer, for example, for levelling purposes. Epec 3610 also has an option for accurate Pt1000 measurement.
-
HopeTech
High-stability internal resistance of the battery Meter.The main battery internal resistance and battery voltage. This product can simultaneously measure the resistance and voltage and to compare battery internal resistance and open-circuit voltage.The CHT3560 standard RS232C and HANDLER interface automated measurement fast and accurate judgment the battery deterioration of the situation, sorting products suitable for battery assembly line and factory inspection. Low resistance characteristics can be used to characterize the mechanical and electrical components down low current test conditions.
-
ENVIROMUX-M-DCS -
Network Technologies Inc
Monitors access with a magnetic bridge sensor, which responds to any magnetic material (no special inserts necessary). Can also be used for monitoring side wall and covers. Includes mounting hardware. For normally closed circuit connection. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft. Wide actuating gap, approximately 1". Dimensions WxDxH (in): 0.5x0.5x2 (Switch), 0.5x0.5x2 (Magnet). Operating temperature: 32 to 158°F (0 to 70°C). Regulatory approvals: RoHS.
-
AEDFA-FTTH -
Amonics Ltd.
Amonics FTTH EDFAs inherit the reliable design of Amonics's optical amplifier technology. They exhibit high output power, high gain with very low noise, and are ideal for FTTH network amplification. Integrated CWDM splitters are available to enable routing of 1310nm and 1490nm data streams from OLT to ONU through EDFAs. The turnkey rackmount EDFAs provide microprocessor controlled alarms and status indicators. An integrated Ethernet TCP-IP computer interface enables easy control, diagnostic functions and data acquisition.
-
LD-LESR-A10 -
Labodam
ESR AnalyzerLD-LESR-A10is a portable unit with Westergren analysis method and infrared sensor measuring principle. It offers measurement range of 1 to 140 mm/h with throughput up to 80 samples/h. It has maximum 40 sample loading capacity at same time and two measuring time: 30 min or 60 min. Designed with touch screen large color display, built-in printer and RS232 interface. Used for analysis of erythrocyte sedimentation rate in hospitals, clinical laboratories and research.
-
LD-LESR-A11 -
Labodam
ESR AnalyzerLD-LESR-A11is a portable unit with Westergren analysis method and infrared sensor measuring principle. It offers measurement range of 1 to 140 mm/h with throughput up to 80 samples/h. It has maximum 20 sample loading capacity at same time and two measuring time: 30 min or 60 min. Designed with touch screen large color display, built-in printer and RS232 interface. Used for analysis of erythrocyte sedimentation rate in hospitals, clinical laboratories and research.
-
HT Series -
Emergent Vision Technologies
Our cameras are available with resolutions of 2, 4, 12, and 20 megapixels in monochrome, color, or near-infrared enhanced (NIR) with full frame rates of up to 338fps, 179fps, 84fps, and 32fps respectively (we can also provide taped on glass). As the first 10GigE industrial digital camera series in the world, our HT cameras obtain their high performance from industrial CMOS sensors with Global Shutter technology in combination with the cross-industry standard 10 Gigabit Ethernet (10GigE) interface.
-
Monarch Instrument
Our fixed mount stroboscopes are designed for installation in applications requiring continuous stroboscopic visual inspection. The MVS is available with xenon or LED light output with adjustable pulse width and focal distance for optimized target illumination. Connect your existing trigger signal or the optional Frequency Controller with LCD. Connect multiple units together in parallel for applications with wide illumination area requirements. Use the optional Audio Interface Box and microphone to create stunning audio driven visual effects.
