Showing results: 406 - 420 of 5968 items found.
-
DVTest Inc.
Super speed “USB 3.1 type C modules” for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for USB 3.1 link untouched.
-
COMMDongle -
Add2 Ltd.
Designed for use with VISUALCONNX and other third-party software, COMMDongle products initially support one or more CAN communications buses.
-
VXI-5524A-3 -
ICS Electronics
* 3.3V power out instead of 5 V on Digital IO bus connector* All othe specifications same as listed above for the VXI-5524A board.
-
YAV90058A -
6TL Engineering
8 RJ45 LAN connectors to VPC ITA 192 pins module
-
YAV90058C -
6TL Engineering
8x RJ45 LAN connectors to VPC RCV 192 pins module
-
Chauvin Arnoux Metrix
This economical, high-performance oscilloscope operates when connected directly to a PC.It uses the PC's screen for display and its memory for its recording capacity.It is a benchtop oscilloscope which is easy to use, stack and transport.
-
The ZT-Series -
Avionics Interface Technologies
The ZT-Series brand of Modular Digitizers, Digital Storage Oscilloscopes, and Waveform Generators support a number of test and measurement applications found in the Defense and Aerospace, Semiconductor Test, and Industrial Control and Automation spaces.
-
ARINC 664 -
Avionics Interface Technologies
AIT’s ARINC 664 test instruments can be used in test and simulation applications that are required to transmit and receive data over the ARINC 664 avionics databus. AIT’s instruments use small form-factor pluggable transceivers (SFP) and support copper or fiber optic physical network interfaces.Using an FPGA based architecture, with multiple embedded processors, the ARINC 664 instruments provide onboard support for upper layer protocol processing (A653, UDP, IP) and utilize DMA to provide optimal data throughput. All ARINC 664 protocol operations, including VL traffic shaping, redundancy management, and IP fragmentation and reassembly, are handled onboard.
-
40-965-910 -
Pickering Interfaces Ltd.
The 40-965-910 is a converter card for the 40-201 Ethernet/AFDX Fault Insertion Switch. Adapts the 78-Pin D-type connector on the front of the module to 4 RJ45 sockets and one 9-way D-type connector for fault signals. Allows the fault insertion testing of Gigabit Ethernet signals.
-
2620 -
Sensoray Co., Inc
Four 32-bit quadrature encodersPWM, period, frequency measurementPeriodic, single-shot outputsCompatible with Linux and WindowsCE Compliant
-
BIUT 820 -
ATSI
Quickly and reliably check any BIU with the BIUT-820 which provides comprehensive, fully automated testing in the field or at the shop.
-
1257A -
Astronics Corporation
The Astronics 1257A is a sixth-generation RFIU design with four Commercial Off-The-Shelf (COTS) options from 1U to 4U. It comes with a new easy-to-use LXI Core 2011-compliant device and new enhanced features.
-
AIM GmbH
AIM’s > ARINC 429 test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. The latest versions also support avionics discrete I/O.
-
PMC-Wizard -
Dynamic Engineering
The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems. The primary application is to provide very high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 Ω. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media, and the noise coupling to the environment
-
LANTAP-10 -
Innovative Control Systems, Inc.
*LANTAP-10 kit comes with 10’ Coaxial cable, 6’ USB cable, 6’ CAT5 cable, BNC Connector and Terminator.*Allows connection of any 10/100/1000 Ethernet equipped system to EPIC equipped *Aircraft LAN or ANY 10base2 need.*No drivers to install. The LANTAP is NOT a USB device. It is only powered by USB.*Complies to IEEE 802.3 10Base-T and 10Base2*LED diagnostics and monitoring indicators