Showing results: 1006 - 1020 of 1228 items found.
-
185 LCT -
Standard Electric Works Co., Ltd
● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable.● The LAN cable tester can verify cable continuity, open, short circuit and miss-wired.● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan functions.● Ground wire test. ● Lock status function.● Buzzer sound warning for wire status.● Display : LED indication for wire status.
-
Neutronics Manufacturing Co.
NMC's Digital Micro Ohm Meters are low cost, compact, light weight, 3½ digit resistance meter suitable for measurements of resistances of cables, wires, transformers, motor windings, coils and contact resistance of switches, connectors, relays and track resistance of PCB's etc. The value of resistance is displayed on 7 segment LED display. Four terminal measurement systems provide measurements free from errors due to contact resistance and test lead resistance.
-
Series SI -
Teledyne Defense Electronics Relays & Coax Switch
Series SI relays are designed to switch high voltage (high power) DC loads. These devices feature the latest generation of High Voltage IGBT Technology as well as an innovative isolated driver to ensure fast power turn on and OFF. The relays feature triggered control input to avoid linear control risks and fast switching times. The relays also offer an LED for status.Available options include:SI60DC100 100A, 0-500 Vdc Load; 4.5-32 Vdc Control
-
RPT-AAA Series -
Ripley Tools LLC
Electronic testing tool designed to check the circuit integrity in new or installed cable up to 5,000 feet (1,500 meters) in length LED indicates DC shorts, splitters & other self-grounding devices in cable while a loud audio tone identifies the line carrying the signal Equipped with a right angle male push-on connector to maneuver in tight areas & a female push-on connector for speed toning Tool includes a pocket clip & (1) AAA 1.5V battery.
-
Green Laser Series -
PowerTECH Co,Ltd.
Adopts the international advanced harmonic oscillated cavity design and laser control technology to realize that laser can obtain good beam quality under high power operation with high long-term stability and narrow laser pulse width. Special cavity inside heat compensation and harmonic conversion technology can realize doubled-frequency conversion of high efficiency. Suitable for laser trimming resistor thin film photovoltaic battery manufacture micro processing LED chip marking PCB.
-
FLIR M500 -
Teledyne FLIR
The gyro-stabilized FLIR M500 cooled thermal camera is our most technologically-advanced M-Series pan and tilt camera ever. Designed around a cryogenically-cooled 640 x 512 pixel Mid Wave Infrared (MWIR) thermal sensor, the FLIR M500 excels at both short and ultra-long range target detection and identification. It features a 14X continuous optical thermal zoom, a color HD camera with 30x zoom, an LED spot-beam, video tracking and radar integration.
-
SystemView -
SEGGER Microcontroller GmbH & Co. KG
SEGGER is announcing the release of SystemView, a free tool enabling the visual analysis of any embedded system. SystemView gives complete insight into the behavior of a program, with minimal side effects on the observed embedded system. SystemView offers cycle accurate tracing of interrupts and task start stop as well as task activation and API calls when an RTOS is used. It visualizes and analyzes CPU load by task and interrupts and scheduler. Test setups with LED and oscilloscope are a thing of the past.
-
RM 1 -
Beck Elektroakustik
Using the RM 1 Tube Checker it is immediately possible to do an exact plate current measurement without doing the often very toilsome procedures mostly necessary with classical devices. Put the electron tube, which should be measured, simply into the accordingly marked test socket, switch the equipment on, select the socket by using the rotary switch (it is indicated by a LED), wait for approx. three minutes till the tube is working stabile and read off the value on the panel meter.
-
Becker Nachrichtentechnik GmbH
Modern receivers for broadcast have a large number of antenna inputs for the different radio bands. The devices of the FDMX series can be used to supply the antenna inputs with RF signals. The devices of the FDMX series splits a sum signal in frequency division multiplex into the individual broadcast bands and the L1 satellite navigation band (GNSS). Additionally, DC loads are provided for each antenna input to simulate active antennas. The presence of remote power supply is indicated by an LED on the units.
-
ST-1504 -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Measures insulation(MΩ), continuity(Ω) and AC voltage.● Instant operation is possible with a push button, convenient timer is provided with automatic power off after three to five minutes to save the battery power.● LED (red) indication when testing insulation and continuity.● Use of a high efficiency and accurate DC-DC converter.● Most suitable for insulation resistance measurement of electrical household appliances, power line distribution and installation.
-
ST-1503 -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Measures insulation(MΩ), continuity(Ω) and AC voltage.● Instant operation is possible with a push button, convenient timer is provided with automatic power off after three to five minutes to save the battery power.● LED (red) indication when testing insulation and continuity.● Use of a high efficiency and accurate DC-DC converter.● Most suitable for insulation resistance measurement of electrical household appliances, power line distribution and installation.
-
Part No. E3P2G -
Teledyne Defense Electronics Relays & Coax Switch
The E3P2G series, three-phase solid state relay is the 2nd generation of the discontinued E3P series. The new design incorporates a high efficiency back-to-back thyristor with direct copper bonding for a longer lifetime expectancy. Over-Voltage protection is provided internally with TVS diodes for the input and output. Additionally our -16 model is designed with an RC snubber and VDR for greater protection to the output to handle all types of loads. The industrial SSR utilizes optical isolation to protect the control from load transients for each phase and has tight zero-cross window for low EMI. A control status LED are standard on all models.Available options include:E3P48D25 Load: 25A, 24-600Vrms ; Control: 4-30Vdc E3P48D50 Load: 50A, 24-600Vrms ; Control: 4-30Vdc E3P48D75 Load: 75A, 24-600Vrms ; Control: 4-30Vdc E3P48D75-16 Load: 75A, 24-520Vrms ; Control: 4-30Vdc ;E3P48D75-16 RC+VDR Output Protection
-
MM-2 -
Dwyer Instruments Inc.
Our compact, low cost Model MM-2 Digital Multimeter with True RMS is ideal for general electrical testing and troubleshooting. This full function multimeter measures DC voltage to 1000 V and AC voltage to 750 V, DC and AC current to 10 A and resistance to 400 Ohms. In addition to volts, amps and ohms, this meter includes audible continuity, diode, LED and transistor hFE tests. The rotary switch allows you to select from any of the functions quickly and easily.
-
KM CAL 09 -
Kusam Electrical Industries Limited
Model-KM-CAL-09 Multimeter Test Calibrator is a Test Instrument for AC / DC Voltage and AC/DC Current with 5 digits bright LED display. The Resistance output has 22 levels. The Test Instrument, mainly used for testing and calibrating various instruments which have DC accuracy level below 0.5 and AC accuracy level below 1, is widely used for the quality testing, measuring and instrument servicing in Electronic manufacturing Enterprises, Scientific Research Institutes, Railway, and Electric Power etc.
-
PeakTech Prüf- und Messtechnik GmbH
Is a high-precision energy cost measuring device for recording the energy consumption of electrical devices and for calculating the current consumption of a device by entering the electricity price. Thanks to the integrated power factor calculation, all modern consumers such as Switching power supplies, TV sets, fluorescent lamps, LED systems and of course ohmic loads such as Electric heaters and hobs can be measured accurately. In addition, the high resolution, the low response characteristic and even very small or stand-by consumers from approx. 1 W can be measured.
