Filter Results By:
Products
Applications
Manufacturers
-
product
Infrared Lens
Zhejiang ULIRvisionTechnology Co., LTD
Ulirvision offers a wide range of range of infrared lens for infrared thermal imaging camera. Below are our featured thermal infrared lens and key factors need to consider for choosing infrared camera lens.
-
product
Lens Antennas
A lens antenna is a directional antenna that uses a shaped piece of microwave-transparent material to bend and focus microwaves by refraction, as an optical lens does for light.[1] Typically it consists of a small feed antenna such as a patch antenna or horn antenna which radiates radio waves, with a piece of dielectric or composite material in front which functions as a converging lens to collimate the radio waves into a beam.[2] Conversely, in a receiving antenna the lens focuses the incoming radio waves onto the feed antenna, which converts them to electric currents which are delivered to a radio receiver. They can also be fed by an array of feed antennas, called a focal plane array (FPA), to create more complicated radiation patterns.
-
product
Lens Calibration
SpyderLENSCAL
A fast, reliable method of measuring and adjusting the focus performance on your camera and lens combinations.
-
product
Lens Measurement Spectrophotometers
LINZA 150
LINZA 150 spectrophotometer is designed for broadband transmittance and reflectance measurement of lenses and lens assemblies (objectives) ensuring that only perfect lenses are approved for lens assemblies, delivered to customers or meet specs provided to your lens supplier. The instrument is perfectly suited for both routine lens measurements and sophisticated improvement of lens production technology: Fast on-axis transmittance measurement of individual convex/concave lenses. Fast on-axis transmittance measurement of lens assemblies (objectives). Unattended on-axis and off-axis reflectance measurement of individual lenses providing measurement data virtually from any area on lens surface (both convex and concave). Ideal for fine-tuning of deposition technology used to produce coatings on lenses.
-
product
Spot-Focusing Lens Antennas
The antenna employs a low loss lens to offer excellent aperture efficiency at 105.96 GHz. The lens antenna is equipped with a standard WR-10 waveguide and UG-387/U-M flange as its input port. It supports linear polarized waveforms.
-
product
Lens Corrected Antennas
Lens corrected antennas are offered with either a circular or rectangular waveguide interface. While lens corrected antennas with a rectangular waveguide interface can only support linear polarization, models with a circular waveguide interface can support various polarization types including horizontal, vertical, left-handed circular, and right-handed circular polarization for broader applications. These antennas are designed and constructed to offer high efficiency, low side lobes and a rugged mechanical configuration. In general, lens corrected antennas are ideal for achieving gain levels of up to 30 dB with moderate side lobe rejections. Additionally, its dielectric lens provides phase error corrections and serves as a radome to protect from environmental conditions.
-
product
Machine Vision Lens
FUJINON HF6XA-5M
This new product, which has an external diameter of 39 mm and a focal length of 6 mm, is the world's smallest* Machine Vision lens which is used for industrial processes such as product inspection and measurement on production lines. HF6XA is a new lens which is designed for compatibility with 2/3" sensors with a pixel pitch of 3.45m (five megapixels). HF6XA is a FUJINON Machine Vision lens designed for compatibility with 2/3" sensors, which has coverage of approximately twice*** the current product, the FUJINON HF8XA, which offers the widest coverage range. In the frequently used environments of customers, the lens is compatible with the ultra-high resolution of 3.45m pixel pitch (equivalent to five megapixels when using a 2/3" sensor) under a large portion of the screen. Furthermore, for a wide range of installations and shooting conditions, the lens boasts "4D High Resolution"*4 performance, mitigating resolution degradation that typically occurs when changing a shooting distance or aperture value and maintaining a high level of even image sharpness across the entire image area at the ultra-high resolution of 4.4m pixel pitch (equivalent to three megapixels when using a 2/3" sensor). Despite being a wide-angle 6mm lens, the lens achieves the world's smallest external diameter of just 39 mm. The lens is ideal for attachment inside compact inspection devices with restricted internal space when wide coverage and consistency is required for reading product codes and serial numbers or for inspecting product shape and appearance.
-
product
Rotman Lens Designer
Rotman Lens Designer (RLD) is a software tool for the design, synthesis, and analysis of Rotman Lenses and their variants. It is based on Geometrical Optics combined with the classical Rotman Lens design equations. It is intended for rapid development and analysis of Rotman Lenses given several physical and electrical input parameters. RLD generates the proper lens contours, transmission line geometry, absorptive port (dummy port) geometry, provides an approximate analysis of performance, and generates geometry files for import into Remcom's XFdtd® for further analysis and fabrication.
-
product
Lens Driver Components
Analog Devices offers a range of lens driver solutions for camera modules in camera phones, camera enabled handsets, DSCs, consumer entertainment, and computer imaging. Lens drivers integrate drivers, waveform control, power management, signal processing, travel control, and more to provide the smallest, lowest power, most complete system solutions with the latest motor/actuator technologies.
-
product
NIR Macro Lens
ML-4
With the ML-4 macro lens, Korima takes the job to an even higher level of certainty and simplicity. Through the ML-4, failure analysts can examine an entire microcircuit at once--rather than in a sequence of small, individual areas.
-
product
FA Lens Macro
ML-N Series
16mm compact body High resolution with low distortion Reasonable price Best matching with peripherals
-
product
Lens Testing Services
Our optical testing instrumentation enables us to make a wide range of measurements on optical systems including various measures of image quality, first order system characteristics, individual element parameters, and many more.
-
product
Lens Test Equipment
ZEISS lenses for technical applications are key components in complex production processes (Machine Vision) as well as in optical metrology, medical applications, traffic enforcement, quality assurance, sports and many other applications. Here they prove their outstanding image performance and reliability. Due to the precise manual adjustment of the helical focusing mount our partners will gain much better results than with comparable lenses.
-
product
Gaussian Optics Lens Antennas
SAG-1441544002-06-S1
Gaussian optics lens antennas are offered with either a circular or rectangular waveguide interface. While Gaussian optics lens antennas with a rectangular waveguide interface can only support linear polarization, models with a circular waveguide interface can support various polarization types including horizontal, vertical, left-handed circular, and right-handed circular polarization for broader applications. Gaussian optics lens antennas are designed and constructed to offer high efficiency, low side lobes and a rugged mechanical configuration. A corrugated feed horn and dielectric lens allow these antennas to form well-defined Gaussian beams. Additionally, the dielectric lens provides phase error corrections and serves as a radome to protect from environmental conditions.
-
product
Cylindrical Lens Measuring Device
ZLM
Optik Elektronik Gerätetechnik GmbH
ZLM is a computer-aided measuring device for geometric parameters of cylindrical lenses, which is used for series production.
-
product
Cylindrical Lens Measuring System
CLM
Optik Elektronik Gerätetechnik GmbH
CLM is a measuring system for geometrical parameters of cylindrical lenses for use in serial production.
-
product
Intraocular Lens Optical Test System
OptiSpheric® IOL R&D
The OptiSpheric® IOL R&D is specially designed for the analysis of single intraocular lenses in research and development. With the OptiSpheric® IOL R&D, important parameters of all types of lenses (monofocal, multifocal, trifocal, toric, aspheric and those with extended depth of focus (EDOF) – whether diffractive, refractive or sectors) can be measured and tested in air or in situ in accordance with ISO 11979.
-
product
MP Custom Lens Camera Module (Monochrome)
E-CAM50_CU9P031_MOD - 5.0
e-CAM50_CU9P031_MOD is a 5 MP custom lens monochrome camera module based on Aptina's MT9P031 CMOS image sensor with S-mount lens holder attached to it. The MT9P031 is a 1/2.5" Optical Form factor, Electronic Rolling Shutter CMOS sensor.
-
product
Standard Gain Horn Conical Lens antennas
Elva’s SLHA series of standard gain horn lens antennas cover the frequency range of 18 to 220 GHz in ten waveguide bands. They can be issued with rectangular or circular waveguide. Lens technology significantly allows decreasing mechanical sizes of horns and correcting beam for the best performance. These horns are ideal solution for measurement gain of other antennas, short range radars and radiometers.
-
product
1MP OV10633 Custom Lens Camera Module
e-CAM1M_CU10630_MOD
e-CAM1M_CU10630_MOD is a High Dynamic Range (HDR), Wide Dynamic Range (WDR), custom lens camera module targeted for surveillance and security applications. This HDR camera module based on the OV10633 sensor from OmniVision is e-con’s first Wide Dynamic Range (WDR) camera module that can stream 1280x720p video at 30fps over its 8-bit digital video parallel interface. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice.
-
product
1MP OV10633 Custom Lens Camera Module
e-CAM1M_CU10630_MOD
e-CAM1M_CU10630_MOD is a High Dynamic Range (HDR), Wide Dynamic Range (WDR), custom lens camera module targeted for surveillance and security applications. This HDR camera module based on the OV10633 sensor from OmniVision is e-con’s first Wide Dynamic Range (WDR) camera module that can stream 1280x720p video at 30fps over its 8-bit digital video parallel interface. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice.
-
product
5.0 MP Custom Lens Camera Module (Monochrome)
e-CAM50_CU9P031_MOD
e-CAM50_CU9P031_MOD is a 5 MP custom lens monochrome camera module based on Aptina's MT9P031 CMOS image sensor with S-mount lens holder attached to it. The MT9P031 is a 1/2.5" Optical Form factor, Electronic Rolling Shutter CMOS sensor. The e-CAM50_CU9P031_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM50_CU9P031_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
product
5.0 MP Custom Lens Camera Module (Monochrome)
e-CAM50_CU9P031_MOD
e-CAM50_CU9P031_MOD is a 5 MP custom lens monochrome camera module based on Aptina's MT9P031 CMOS image sensor with S-mount lens holder attached to it. The MT9P031 is a 1/2.5" Optical Form factor, Electronic Rolling Shutter CMOS sensor. The e-CAM50_CU9P031_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM50_CU9P031_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
product
e-CAM1M_CU10630_MOD - 1MP OV10633 Custom Lens Camera Module
e-CAM1M_CU10630_MOD is a High Dynamic Range (HDR), Wide Dynamic Range (WDR), custom lens camera module targeted for surveillance and security applications. This HDR camera module based on the OV10633 sensor from OmniVision is e-con’s first Wide Dynamic Range (WDR) camera module that can stream 1280x720p video at 30fps over its 8-bit digital video parallel interface. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. This 1MP WDR/HDR camera module is compatible with almost all of the popular Application Processor families such as TI OMAP, TI Sitara, NXP/Freescale i.MX, Marvell Xscale, Samsung etc and also compatible with Digital Signal/Media Processors such as TI OMAP35x, TI DaVinci DM37x, DaVinci DM3xx etc. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice. The camera module is mounted with an industry-standard S-mount M12P0.5 lens holder allowing our customers to choose a lens of their choice.
-
product
5 Mega Pixel Custom Lens Camera Module
e-CAM51_CU5640_MOD -
The e-CAM51_CU5640_MOD is a small form-factor pluggable 5 Mega pixel custom lens camera module. Moreover, a wide variety of interchangeable lenses can be used on this custom camera module. It is based on OV5640 CMOS Image sensor from Omnivision Inc. The e-CAM51_CU5640_MOD is designed to connect with any application processor that has Parallel/MIPI digital video interface.
-
product
5 Mega Pixel Custom Lens Camera Module
e-CAM51_CU5640_MOD
The e-CAM51_CU5640_MOD is a small form-factor pluggable 5 Mega pixel custom lens camera module. Moreover, a wide variety of interchangeable lenses can be used on this custom camera module. It is based on OV5640 CMOS Image sensor from Omnivision Inc. The e-CAM51_CU5640_MOD is designed to connect with any application processor that has Parallel/MIPI digital video interface.
-
product
Custom Lens USB 3.0 Camera Board (Color)
See3CAM_CU130
See3CAM_CU130 is an Ultra HD USB camera board based on Aptina™ AR1820HS sensor. It streams Ultra HD (3840x2160) at 30fps over USB3 in compressed MJPEG format, Full HD (1920x1080) at 30fps and HD (1280x720) at 60fps in both uncompressed and compressed MJPEG formats. This Custom Lens camera board is also backward compatible with USB 2.0, although in USB2, this camera supports fewer resolutions at lower frame rates.
-
product
HOT MWIR Camera Module + Continuous Zoom Lens
Neutrino® IS Series
Neutrino IS series combines Teledyne FLIR’s world-class mid-wavelength infrared (MWIR) OEM camera modules and continuous zoom (CZ) lenses to offer high–performance imaging solutions with various FPA resolutions and CZ zoom/FOV ranges. Neutrino IS lowers development and manufacturing risk and improves time-to-market. Cutting-edge HOT FPAs, long life and low vibration linear coolers, common camera interfaces, and fully athermalized lenses make for the best-in-class solution. Each camera module and lens are designed for each other, providing optimal performance not achievable when buying and integrating cameras and lenses from multiple sources.
-
product
1.3 MP Custom Lens NIR Camera Module (Monochrome)
e-CAM10_CU0130_MOD
The e-CAM10_CU0130_MOD is a 1.3 MP NIR Camera module (Monochrome) based on the Aptina / ON Semiconductor AR0130CS CMOS image sensor with S-mount lens holder attached to it. The AR0130 is a 1/3” Optical Form factor, Electronic Rolling Shutter CMOS sensor with enhanced sensitivity in the Near Infrared region and superior low light performance. The e-CAM10_CU0130_MOD is designed to connect with any Application Processor that has parallel digital video interface. The standard S-Mount lens holder can accommodate a wide range of lenses based on the customer choice. e-CAM10_CU0130_MOD’s S-Mount holder can also house a fisheye lens or a zoom lens to meet their application requirements.
-
product
4K Custom Lens USB 3.0 Camera Board (Color)
See3CAM_CU135
See3CAM_CU135 is a 13MP fixed focus 4K USB camera board with good low light performance and iHDR support. This 4K board camera is based on 1/3.2" AR1335 CMOS image sensor with advanced 1.1µm pixel BSI technology from ON Semiconductor® It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It is a Plug-and-Play camera (UVC compliant) for Windows and Linux. This 4K board camera is also backward compatible with USB 2.0 host ports.
