Showing results: 61 - 75 of 104 items found.
-
6103/6106 -
Applied Instruments, Inc.
Enable a single technician to perform return band alignment with this easy to use return band alignment system for CATV. This system consists of a headend signal level receiver/telemetry transmitter (the HECTER 6103) and a small, field portable, dual-carrier signal generator/telemetry receiver unit (HECTER'S PUP 6106).
-
Extech RH200W -
Extech Instruments Corporation
Extech’s Multi-Channel Hygro-Thermometer, with easy-to-read 1.3" (33mm) digits, displays indoor Temperature and Humidity levels. You can connect up to 8 wireless transmitters to remotely measure Temperature/Humidity levels up to 98ft (30m) away. The LCD is designed with an auto-night light and it displays icons that indicate indoor comfort levels and trending arrows that show the increase, decrease or constant readings. It also records Min/Max for the duration of each measurement session. Ideal for multi-room environmental monitoring for restaurants, manufacturing facilities, offices, homes, greenhouses, and storage/archive buildings.
-
Laurel Electronics, Inc
Laureate TM Series serial output transmitters can be jumpered for two signal levels: RS232 or RS485. Two serial protocols are selectable in software: Modbus or Laurel's Custom ASCII.Modbus protocol operation is fully compliant with the Modbus Over Serial Line Specification V1.0 (2002) for 2-wire, half-duplex connection.
-
LS-11-F -
Lumistar Inc.
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
L-Band -
QuestTel
QuestTel''s Satellite L-Band optical fiber Transmitter/Receiver set offers high pefromance and cost effective alternative to conventional coaxial systems. The L-Band Transmitter and Receiver pair is used for transporting L-Band RF over fiber from the antenna to the satellite receiver. Additionally transmitter provides optional 13/18V LNB power as well as Automatic Gain Control (AGC) to manage RF input level. By transporting the L-Band RF over fiber this range can be extended from several hundred feet to over 80 miles. Since optical signal is not affected by electromagnetic field, the quality of your signal will always stay at the high level. Also this fiber solution is more cost effective than coaxial system, as well as more reliable and flexible.
-
Process Insights, Inc.
If you are concerned over unsafe levels of oxygen explore a complete line of oxygen deficiency monitors. Our portfolio of Alpha Omega Instruments trace and percent oxygen analyzers and transmitters, safety monitors (oxygen deficiency) and moisture monitors and cost-effective and reliable. We supply many instruments to medical, aerospace, and municipalities.
-
DCHT -
Lectrosonics, Inc.
The DCHT portable digital stereo transmitter is designed for use in film and TV production as both a wireless audio link from a bag or cart system to cameras and as a portable IFB transmitter paired with the Duet digital wireless M2R receiver packs. The DCHT accepts two channels of mic or line level analog signals or an AES digital signal from a mixer and transmits to the receiver or receivers in a purely digital format. The digital architecture of the new DCHT is a third-generation design with specially developed, high-efficiency circuitry for extended operating time on two AA batteries.
-
9950 -
Georg Fischer Signet
The 9950 Transmitter is a two channel controller that supports two sensors of same or different types in one instrument. The sensor types supported by the 9950 are Signet Flow, pH/ORP, Conductivity/Resistivity, Salinity, Temperature, Pressure, Level, Dissolved Oxygen, and devices that transmit a 4 to 20 mA signal with the use of the 8058 iGo® Signal Converter.
-
NPRT 2200-F -
Applied Instruments, Inc.
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
VRT2 -
Lectrosonics, Inc.
Up to six VRT2 modules may be installed per each 1RU Venue 2 receiver frame. Each module supports up to 3072 tunable frequencies across a 75 MHz range (three standard Lectrosonics blocks), matching the tuning ranges of SSM, LT and LMb "large bandwidth" transmitters. VRT2 modules incorporate Lectrosonics’ new IQ dynamic tracking filters, which accommodate a wide range of transmitter RF power levels while also enabling extremely tight channel spacing—critical features as the available RF spectrum continues to shrink.
-
5501 CB -
Standard Electric Works Co., Ltd
● The 5501 CB transmitter is a great tool for locating and identifying cables and individual conductors● Locates both powered and unpowered cables ● Voltage measurement for cables: ACV 12V~450V DCV 12V~450V● Signal transmission • Transmission power level selection (includes 1, 2, 3) • Transmission signal code selection (includes F, E, H, d, L, C, O, A)● Flashlight & backlight function● Silent mode (disable button beep)● Level bar display on LCD screen (transmission power level indication)● Action wave display on LCD screen (when signal is transmitted)● Auto power-off function
-
Model: DS-5220 -
De Vries Scientific
The S-Band PCM/FM Transmitter is a synthesized microwave signal source providing low phase noise with a high level signal output. The unit can be set to any frequency within the band of design via a USB or RS-232/422/485 computer command. The oscillator is phase locked to an internal TCXO reference. The oscillator provides a stable low noise source for PCM data transmission.
-
Model: DS-5210 -
De Vries Scientific
The S-Band Video Transmitter is a synthesized microwave signal source providing low phase noise with a high level signal output. The unit can be set to any frequency within the band of design via a USB or RS-232/422/485 computer command. The oscillator is phase locked to an internal TCXO reference. The oscillator pro-vides a stable low noise source for video transmission.
-
Meriam Process Technologies
Meriam's flagship products, the MFC5150 HART Communicator which enables direct communication from any HART transmitter wirelessly and the MFT 4010 Modular Calibrator, which delivers the versatility of a calibrator and the convenience of HART Communications afford Meriam the advantage of providing products with the highest level of innovation for commissioning, configuring and maintaining devices to allow for efficient process operations. These smart devices were designed to optimize process automation via HART Communication by offering analytic support for flow, level, pressure, temperature and valve applications.
-
VORTEX -
TeamCast
VORTEX is a very innovative and advanced solution that supports ATSC 1.0 waveform on an optimized hardware platform.It has been especially designed to meet transmitter manufacturer’s demand for integrating a “read-to-use” and future proof modulator/exciter within their own designs.Fully controlled via a friendly WEB GUI and via SNMP, VORTEX features some very unique functionalities dedicated to control the transmitter (TX) such as a Power Measurement Unit (measuring in real-time the forward and reflected power levels), the TX power ON/OFF control system and the Automatic Gain Control (AGC) mechanism.VORTEX Digital Adaptive Precorrection circuits, powered by TeamCast GAP® – Green Adaptive
