Filter Results By:

Products

Applications

Manufacturers

Level

high or low along a bead it's a measure referenced.

See Also: Liquid Level, Signal Level Meters, Level Transmitters, Depot Level Test


Showing results: 3001 - 3015 of 3779 items found.

  • Type 2 Sound Meter Kit - Digital Sound Meter, 94dB Sound Calibrator and Carrying Case

    Extech 407732-KIT - Extech Instruments Corporation

    This Type 2 Sound Level Meter Kit meets ANSI and IEC 651 Type 2 standards. Ideal for noise surveys in the workplace, installing fire alarms and speaker systems and enforcing noise ordinances. Measures from 35 to 130 dB in 2 ranges and has an accuracy of ±1.5 dB. Data hold and Max hold functions. Backlit display allows use in dimly lit areas. Includes plastic carrying case for meter and calibrator.

  • VAW Meters (Performance Test)

    Premier Electrosystems

    VAW meters indicate the voltage, current, wattage among other parameters that are crucial for testing of any product.Introduction of composite Volt-Amp-Watt Meters by Premier Electrosystems in 1985 has been a runaway success; mainly due to their performance and reliability. Premier Electrosystems have been the pioneers of multi parameter meters i.e. Voltage, Current, Wattage, Kilo Watt hour, Frequency, Power Factor, Run hour, Load hour, 13 level THDs in a single meter

  • Linear Amplifiers

    LA Series - Motion Control Systems, Inc.

    Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.

  • Isolation Amplifier

    Dr. Hubert GmbH

    Isolation amplifiers are indispensable components for signal conditioning. There are several reasons that make galvanic potential isolation necessary. Examples for this are personal protection, on the one hand, as required in medical engineering to ensure contact of persons with life-threatening voltages. On the other hand, different safety aspects, such as protection of IT systems may require the use of an isolation amplifiers. If ground loops need to be separated or if a small differential voltage with a high common-mode level must be determined, the isolation amplifier is the device of your choice.

  • ScanBridge

    JT 2154 - JTAG Technologies Inc.

    The JT 2154 is an experiment board based on National Semiconductor’s STA111 device, aimed at users looking to utilise addressable bridge/multiplexors within their designs, and thus set-up ‘system level’ JTAG access. The unit can also be used in semi-permanent installations to expand the TAP (Test Access Port) count on JTAG Technologies controllers in order to address highly segmented designs. Built-in support for ScanBridge-type devices within ProVision allows easy set-up of TAP assignments and device addressing.

  • JTAG Boundary-Scan Controller for PXI and PXI-Express 'Hybrid' Slots or Plug-In Controller for PXI-Express Peripheral Slot

    JT 37x7/PXI - JTAG Technologies Inc.

    High speed and performance JTAG Boundary-scan controller for PXI and PXI-Express ‘hybrid’ slots or plug-in controller for PXI-Express peripheral slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘

  • Pulse Pattern Generator, 3.35 GHz, dual-channel

    81134A - Keysight Technologies

    When timing and performance requirements are critical, for example in high-speed serial bus applications like PCI Express or Serial ATA, its fast rise times and low intrinsic jitter allow the precise and in-depth characterization of devices, e.g. receivers or backplanes. On top of that, it allows to generate application-specific signal levels like pre- and de-emphasis (PCI Express) or squelch (Serial ATA). The Keysight 81134A lets you test your DUT instead of the pulse or data source!

  • Passive Oscilloscope Probes

    5900 SERIES - Probe Master Inc.

    Probe Master's new 5900 series passive oscilloscope probes are available in 400 MHz & 500 MHz bandwidths. Probes are also available with readout actuators for oscilloscopes with the readout feature. The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.The probe body is made of high impact ABS. Soft molded strain reliefs at all stress points assure long cable life. In short it has been designed to offer you high performance coupled with high quality.

  • Frequency Shaped Isotropic Electric Probes

    PI-SH-FCC, PI-SH-ICNIRP - EMC Test Design, LLC

    An isotropic electric field probe with shaped frequency response meeting the ICNIRP or FCC RF safety standards for occupational and general public exposure limits (see the specified frequency ranges below). Meter readings are shown in % of the STD – standard reference level, eliminating the need to know the source frequency. Probe output is proportional to RF power density in the whole specified power range, producing the correct RF power measurements in single and multi-signal environments, typically present at multiple antenna sites.

  • Digital Anemometers

    Bestone Industrial Ltd.

    This multifunction anemometer provides instant data such as Air Speed and Temperature in Dual Level LCD display with Backlight. This tool has wide measuring range of wind speed from 0 ~ 45m/s (0 ~ 8800ft/min) and temperature from 0 ~ 45°C (32 ~ 113°F). This weather device is an ideal tool for windsurfing, sailing and kite flying. You can also use it for industrial and home purposes such as measuring speed and temperature of CPU computer fans, air-conditioners, airflow over the roof or walls.

  • PXI 8 Slot BRIC 308x4 1-Pole (7 sub-cards)

    40-562A-121-308X4 - Pickering Interfaces Ltd.

    This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.

  • PXI 8 Slot BRIC 10x32 1-Pole (2 sub-cards)

    40-562A-121-10X32 - Pickering Interfaces Ltd.

    This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.

  • PXI 8 Slot BRIC 506x8 1-Pole (11 sub-cards)

    40-560A-121-506X8 - Pickering Interfaces Ltd.

    This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.

  • PXI 8 Slot BRIC 138x16 1-Pole (6 sub-cards)

    40-560A-121-138X16 - Pickering Interfaces Ltd.

    This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.

  • PXI 8 Slot BRIC 368x8 1-Pole (8 sub-cards)

    40-560A-121-368X8 - Pickering Interfaces Ltd.

    This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.

Get Help