Filter Results By:

Products

Applications

Manufacturers

Level

high or low along a bead it's a measure referenced.

See Also: Liquid Level, Signal Level Meters, Level Transmitters, Depot Level Test


Showing recent results 3196 - 3210 of 3361 products found.

  • Single 32 to 1 Terminated 50 600MHz PXI RF Multiplexer

    40-767-001 - Pickering Interfaces Ltd.

    This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk. These RF multiplexers exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 600MHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths has been minimized by careful attention to the mechanical and electrical design. User connections are made via SMB connectors; you can find the associated RF cable & connector accessories data sheet under the downloads tab above.

  • Impedance Matching Pad

    Pasternack Enterprises, Inc.

    Pasternack impedance matching pad (aka resistive impedance transformers or minimum loss pad) category is passive coaxial components that allow impedance matching between 50 Ohm and 75 Ohm systems without introducing a lot of reflection to the circuit. Impedance matching pads from Pasternack are ideal for applications requiring a connection between a 50 Ohm cable and 75 Ohm system. Matching pads for impedance from Pasternack are available in many male/female in-series and between-series connectorized configurations including Type N, BNC, SMA, TNC and F. Many of our RF impedance matching pad components are RoHS and REACH compliant. Pasternack’s matching impedance pads have very good VSWR levels ranging between 1:20:1 and 1:35:1 and are accurate within 0.5 dB. Our RF matching pad have frequencies ranging from 500 MHz to 3 GHz. Maximum attenuation loss for our matching pads is 5.7dB. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this impedance matching pad series is in-stock. Not only in stock, but these RF impedance matching pad products will ship the same-day as they are purchased.

  • Quad 8 to 1 50 600MHz PXI RF Multiplexer

    40-762-004 - Pickering Interfaces Ltd.

    This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk. These RF multiplexers exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 600MHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths has been minimized by careful attention to the mechanical and electrical design. User connections are made via SMB connectors; you can find the associated RF cable & connector accessories data sheet under the downloads tab above.

  • Quad 8 to 1 Terminated 50 600MHz PXI RF Multiplexer

    40-763-004 - Pickering Interfaces Ltd.

    This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk. These RF multiplexers exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 600MHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths has been minimized by careful attention to the mechanical and electrical design. User connections are made via SMB connectors; you can find the associated RF cable & connector accessories data sheet under the downloads tab above.

  • 75 Ohm Mini SMB Connector

    Pasternack Enterprises, Inc.

    75 Ohm Mini SMB connector category from Pasternack includes many part numbers, the majority are RoHS and REACH compliant. 75 Ohm Mini SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our 75 Ohm Mini SMB connectors are built to precise microwave and RF industry specifications. Pasternack 75 Ohm Mini SMB connectors are built in jack or plug gender with 75 Ohm impedance. Mini-SMB 75 Ohm connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel or mountless options. These 75 Ohm Mini SMB connector designs include crimp/solder or solder attachment methods. We offer 75 Ohm Mini-SMB connectors with standard or high performance levels manufactured with brass or stainless steel bodies. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm mini SMB connector series is in-stock. Not only are these mini-SMB 75 Ohm connectors in stock, they also ship the same day as they are purchased.

  • Quad 4 to 1 Terminated 50 600MHz PXI RF Multiplexer

    40-761-004 - Pickering Interfaces Ltd.

    This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk. These RF multiplexers exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 600MHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths has been minimized by careful attention to the mechanical and electrical design. User connections are made via SMB connectors; you can find the associated RF cable & connector accessories data sheet under the downloads tab above.

  • Dual 16 to 1 Terminated 50 600MHz PXI RF Multiplexer

    40-765-002 - Pickering Interfaces Ltd.

    This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk. These RF multiplexers exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 600MHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths has been minimized by careful attention to the mechanical and electrical design. User connections are made via SMB connectors; you can find the associated RF cable & connector accessories data sheet under the downloads tab above.

  • Single 8 to 1 50 600MHz PXI RF Multiplexer

    40-762-001 - Pickering Interfaces Ltd.

    This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk. These RF multiplexers exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 600MHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths has been minimized by careful attention to the mechanical and electrical design. User connections are made via SMB connectors; you can find the associated RF cable & connector accessories data sheet under the downloads tab above.

  • Programmable DC Electronic Load - (Economical)

    63200E Series - Chroma ATE Inc.

    The 63200E series are high power DC loads that include a choice of three operating voltages, 150V, 600V and 1,200V, with power levels from 2kW to 24kW and up to 2,000A in a single unit. Power levels can increase up to 240kW when multiple units are paralleled.These high power loads are designed for testing a wide range of EV products including DC charging stations, car battery discharge, on board charger power components, and other power electronics components. With its high power capabilities, parallel control and dynamic synchronization functions make this load ideal for automotive batteries, fuel cells and more. The 63200E load's master/slave control application enables units with the samevoltage specification to be used in parallel and synchronized dynamically to meet the power testing requirements. In addition, a 255-set data storage function has been built-in for recall of the stored settings at any time. When used in automated testing, the save and recall functions can save a great deal of time.

  • Digital Panel Mount Load Cell Meter

    MODEL DPM-3 - Transducer Techniques, Inc

    The DPM-3 is a smart Plug & Play TEDS IEEE 1451.4 compliant Digital Panel Mount Load Cell meter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the DPM-3 will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the DPM-3 can be set up by simple front panel push buttons. The DPM-3 can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, etc. The DPM-3 samples 60 readings per second (50 for 50Hz operation) for fast control response and true peak/valley reading capability. The meter has an adaptive digital filter that can automatically select the best time constant for minimum noise, yet respond rapidly to an actual change in signal level. The peak and valley values can be displayed by a push of a button on the front panel. Auto-tare allows the meter to be set to zero for any input signal level. Available options include dual relays, analog output, serial communications, and low voltage power supply.

  • Limiting Amplifier

    Pasternack Enterprises, Inc.

    Pasternack limiting amplifier category covers a wide frequency range are typically used to protect sensitive microwave receivers by “limiting” excessive input power. This wideband limiting amplifier series product line from Pasternack accepts a wide range of input power levels, while responding with a limited range of output powers with a saturated power output deviation over the frequency range, independent of the input. These RF limiting amplifiers demonstrate a wide input dynamic range, high gain levels typical gain while exhibiting excellent gain flatness performance.Limiting amplifiers are housed in rugged hermetically-sealed packages and are designed to withstand harsh environments with a wide range of operating temperatures. Our amplifiers are unconditionally stable and include built-in voltage regulation, bias sequencing and reverse bias protection for added reliability. Over-voltage protection is installed externally for easy repair and the amplifiers are fully matched internally for 50 Ohm input and output, which eliminates the customers need for any additional sensitive external RF tuning components. Broadband limiting amplifiers with wide dynamic range commonly used in electronic warfare and military communications systems.Most all Pasternack limiting amplifiers are EAR99.

  • Frequency Dividers

    Pasternack Enterprises, Inc.

    Frequency dividers from Pasternack utilize advanced GaAs HBT MMIC semiconductor technology that produces low additive single sideband (SSB) phase noise performance with typical levels down to -155 dBc/Hz at 100 KHz offset. Input power ranges from -20 to +10 dBm with output power ranging from -1 to -4 dBm depending on the model. Additional performance includes a fast output transition time of 100 picoseconds, high reverse leakage levels up to 85 dB, single +5V DC power supply, and an operating temperature range of -55C to +85C. All models are EAR99. These frequency dividers are designed into compact miniature packages that support field replaceable SMA connectors and mounting fixtures that can be removed for convenient PCB "drop-in" applications. The rugged Kovar package designs are gold-over-nickel plated and hermetically sealed and guaranteed to meet MIL-STD-883 environmental test conditions for temperature cycle and fine & gross leak testing. These versatile high-rel designs are available in-stock for immediate shipment.

  • Active Frequency Multipliers

    PE88X Series - Pasternack Enterprises, Inc.

    Pasternack's PE88X series Active Frequency Multipliers simplify system designs by offering high output power levels and are important building block components used in local oscillator (LO) chains for radar, communication receivers and frequency sources to extend frequencies and achieve optimal performance. They support multiple markets and applications including electronic warfare, electronic countermeasures, point-to-point radio, VSAT radio, test instrumentation and telecom infrastructure.These active frequency (x2) multipliers double input frequencies ranging from 4 to 23 GHz up to desirable microwave and mm-wave output frequencies ranging from 8 GHz to 46 GHz. Additionally, these new designs use highly efficient GaAs PHEMT semiconductor technology with integrated amplifiers that produce high output power levels up to +17 dBm with excellent fundamental and harmonic suppression. This can eliminate the need for an external LO buffer amplifier stage and additional support circuitry. Another key feature is low additive phase noise performance, as low as -142 dBc/Hz at 100 KHz offset.

  • Intelligent Wireless High-voltage Phasing Tester

    TAG-9000 - Wuhan Nanrui Electric Co,. Ltd

    TAG-9000 Intelligent Wireless High-voltage Phasing Tester is a fully intelligent wireless high and low voltage voice phasing tester, which break the the problem of voltage level limit of traditional phasing tester, can test phase in very low voltage circuit, can fully realize automatic phasing test from 10V to 550KV, such as 400V, 10kV, 35kV, 66kV, 110kV, 220kv, without the need to purchase multiple sets of phasing tester or configure high and low voltage detector according to the voltage levels, it has the advantage of cost savings, convenient to carry and saving time. As for phasing test on high voltage circuit (the voltage exceeds 400V), can make the metal probe of detector gradually close to the conductor, when the detector induct the signal of electric field, the phase testing can be completed, do not need to directly contact with high-voltage wire, which is more safety. This phasing tester also has the functions of testing phase position, frequency, phase sequence, checking  electricity, transformer group judgment and so on.

  • Media Files Player/Viewer/Analyzer/Converter

    VQV - VideoQ Inc

    VQV is a compact, but powerful program, featuring: Raw YUV/Y4M/BMP files player with sophisticated viewer/analyzer functionality Wide range of frame sizes, input and output formats; powerful "Save as" file format converter Displays XY positions, YUV and RGB levels of every pixel; switchable zoom ratio and signal gain Automatic measurement of Active Image size and position – LetterBox and PillarBox detector YUV and RGB levels display, video frame information, Black Crash and White Crash statistical analysis Built-in high-gain spatial and temporal high-pass filters reveal even hardly visible artefacts Selectable RGB, Y, UV, R, G or B view channels, adjustable filter mask size and position Right-click submenu allows fast creation of snapshots or thumbnail .BMP images Running multiple VQV instances provides for quick frames/profiles comparison and benchmarking Easy-to-use tool, instantly revealing your video camera, codec, scaler, converter or other video device performance Input and output uncompressed video material data – bit by bit, pixel by pixel, frame by frame Fast and effective tool for 3G-SDI/HD-SDI/SDI/HDMI/LAN/WAN equipment testing and video data fidelity verification Ideal tool for development labs, software developers and high volume manufacturers