Filter Results By:

Products

Applications

Manufacturers

Light

Visible spectrum of electromagnetic radiation from 400nm to 700nm.

See Also: Illumination, Lighting, Lightning, Lightwave, Daylight, Luminescence


Showing recent results 1906 - 1920 of 1977 products found.

  • Ultra-high Vacuum Ф4 Kelvin Probe

    KP Technology

    Our Ф4 Ultra-high Vacuum Scanning Kelvin Probe system gives the user full access to work function measurements under vacuum with the ability to alter the temperature from 77 K to 860 K. The Kelvin probe measurement has resolution of 1 - 3 meV for a 2 mm tip on a conducting sample. The sample is mounted on a plate that is located on a motorized (x, y, z) translator attached to a stainless steel vacuum chamber. Phi 4 also comes with a photoemission spectroscopy system with a tunable source (3.4 - 7.0 eV). The deep ultra-violet (DUV) light spot measures approximately 3 x 4 mm. Absolute work function measurements can be obtained with this system in the range of 4.0 - 6.5 eV with an accuracy of 0.05 - 0.1 eV.

  • The Leading Measurement System for the Analysis of Porous Materials

    ELWIS - Autoneum Holding AG

    ELWIS (Evaluation of Light Weight Impedance System) offers a full and rapid characterization of porous materials based on the analysis of a single sample. The ELWIS system consists of the ELWIS-A and ELWIS-S components which can be used independently from each other although both applications are needed for a complete material simulation.ELWIS-A measures acoustic parameters that are needed to evaluate the acoustic performance of sound insulation and sound-absorbing multi-layer materials. An additional impedance tube for absorption measurements at higher frequencies is available for ELWIS-A.ELWIS-S measures structural parameters that are needed to simulate the dynamic and acoustic behavior of sound packages in the medium to low frequency range (including the "Poisson Ratio" for foam materials).ELWIS is very easy to operate: Thanks to its user-friendly software, the system can also be used to obtain reliable results by users with only limited experience in the characterization of porous materials.

  • 2 phase 120/240VAC SDP-30KW split phase inverter

    SDP-30KW - Zhejiang Sandi Electric Co., Ltd

    SANDI SDP series Pure Sine Wave Inverter is the one of the most advanced technology DC to AC conversion products in the world, it’s suitable use for areas without electricity, providing a complete power solution for strict demand applications. With SVPWM technology it has high conversion efficiency, high instantaneous power and low losses power output pure sine wave, applying to capacitive, inductive and nonlinear mixed-load, with superior load capacity, perfect protection function: overload, short circuit, low/over battery voltage, improper operation etc, which won’t cause mechanical failures. This Inverter is very suitable for solar power systems, wind power generation systems, wind and solar hybrid generation systems. The inverter can supply AC power to all kinds of electric equipment, air conditioners, electric motors, refrigerators, fluorescent lights, televisions, electric fans and other industrial power supply.

  • Omni-λSeries Imaging Spectrograph

    Omni-λi - ZOLIX

    Zolix Imaging Spectrometer includes different focal length 320mm, 500mm, 750mm; ◆Manual micrometer adjustable slits for precision control of incoming light. Motorized Slit and fixed slit is optional. • More than 100 gratings for the best spectral range, throughput and dispersion to meet your application ◆DSP controlled stepping motor scanning system provides superior precision and repeatability of wavelength positioning ◆Optional internal shutter or six-position filter wheel for experiments requiring background removal or signal attenuation ◆Installation and set-up through USB 2.0 computer interfaces • Stand-alone Omni Series monochromator control software for basic scanning and calibration. Also includes utilities for grating updates and communications ◆ Active X control support Visual Basic, C++ and Delphi drivers allow users to design their own acquisition programs ◆ZolixScan data acquisition software provides a simple user interface for easy data acquisition and experimental set-up

  • Spectrograph & Monochromators

    ZOLIX

    Manual micrometer adjustable slits for precision control of incoming light. Motorized Slit and fixed slit is optional. More than 100 gratings for the best spectral range, throughput and dispersion to meet your applicationDSP controlled stepping motor scanning system provides superior precision and repeatability of wavelength positioningOptional internal shutter or six-position filter wheel for experiments requiring background removal or signal attenuationInstallation and set-up through USB 2.0 computer interfaces Stand-alone Omni Series monochromator control software for basic scanning and calibration. Also includes utilities for grating updates and communications Active X control support Visual Basic, C++ and Delphi drivers allow users to design their own acquisition programsZolixScan data acquisition software provides a simple user interface for easy data acquisition and experimental set-up

  • Cassegrain Antennas

    Sage Millimeter, Inc.

    Cassegrain antennas are offered with a 6”, 12”, 18”, 24”, 36” and 48” diameter main reflector dish. These antennas are designed and manufactured with the highest performance and quality. The main advantages of the Cassegrain antenna are its low loss, low profile and light weight compared to other high gain antennas, such as prime focus and lens corrected antennas. As a downside, this antenna has relatively high side lobe levels compared to other antennas due to the interference of the sub-reflector’s supporting structure. To ensure good performance, the supporting structures are specially designed to keep side lobe levels under 18 dB for narrow band operations and under 16 dB for broadband operation. The standard offering covers the frequency range of 18 to 110 GHz, but custom frequencies can be requested. The operating bandwidth of these antennas is mainly limited by the circular waveguide’s dominant mode operation. While standard models are equipped with a circular waveguide interface, a rectangular waveguide interface is also available.

  • Fourier Transform Optical Spectrum Analyzer, 600 - 1700 nm

    OSA202C - Thorlabs, Inc.

    Thorlabs' Optical Spectrum Analyzers (OSAs) perform highly accurate spectral measurements. Compatible with fiber-coupled and free-space light sources, these compact benchtop instruments suit a wide variety of applications, such as analyzing the spectrum of a telecom signal, resolving the Fabry-Perot modes of a gain chip, and identifying gas absorption lines. Many commonly available OSAs use grating-based monochromators, which have slow acquisition times due to the need to mechanically scan the grating and average out noise at each wavelength. Thorlabs' OSAs acquire the spectrum via a Fourier transform using a scanning Michelson interferometer in a push/pull configuration. This approach dramatically improves the acquisition time, enables a high-precision wavelength meter mode with 7 significant figures and ±1 part-per-million accuracy, and allows the included software to provide robust statistical analysis of the acquired spectra, as explained in the Design tab.

  • Fourier Transform Optical Spectrum Analyzer, 350 - 1100 nm

    OSA201C - Thorlabs, Inc.

    Thorlabs' Optical Spectrum Analyzers (OSAs) perform highly accurate spectral measurements. Compatible with fiber-coupled and free-space light sources, these compact benchtop instruments suit a wide variety of applications, such as analyzing the spectrum of a telecom signal, resolving the Fabry-Perot modes of a gain chip, and identifying gas absorption lines. Many commonly available OSAs use grating-based monochromators, which have slow acquisition times due to the need to mechanically scan the grating and average out noise at each wavelength. Thorlabs' OSAs acquire the spectrum via a Fourier transform using a scanning Michelson interferometer in a push/pull configuration. This approach dramatically improves the acquisition time, enables a high-precision wavelength meter mode with 7 significant figures and ±1 part-per-million accuracy, and allows the included software to provide robust statistical analysis of the acquired spectra, as explained in the Design tab.

  • PXI General Purpose Switches

    Keysight Technologies

    The PXI general purpose switch modules deliver fast, reliable switching in a variety of configurations. Cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids with independent, single-pole, double-throw (Form C) or single-pole, single-throw (Form A) switches in a single PXI module. Choose between the high-speed, long-life reed relays capable of switching up to 100Vrms with up to 1A and 25W of power, or the higher power armature relays capable of switching up to 250Vrms, with up to 2A and 60W of power. The general purpose line also includes a module that offers the performance you need to switch heavy loads with up to 300W (DC resistive load)/1250W (AC resistive load).

  • Microwave Wideband Externally Modulated Transmitters (without RF Amp)

    MT80 (30KHz~40GHz) - Hangzhou Huatai Optic Tech. Co., Ltd.

    MT80 series microwave optical transmitter, adopts external modulation technique, are able to transmit 40GHz microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 40Gb/s high speed communication system. MT80 adopts low noise, narrow linewidth CW DFB laser as light source; LiNbO3 external modulator as signal modulation, no laser chirp, low dispersion distortion, high extinction ratio, Full-transparency operation mode. It can be applied in long distance and extra-long distance transmission after EDFA.

  • Microwave Wideband Externally Modulated Transmitters

    MT82 (30KHz~40GHz) - Hangzhou Huatai Optic Tech. Co., Ltd.

    MT82 series microwave optical transmitter, adopts external modulation technique, are able to transmit 40GHz microwave RF signal with long distance, wide bandwidth, and flat responsibility. They provide an outstanding linearity fiber optical communication for analogue and digital wideband microwave application. Due to avoidance of using expensive coaxial cable or wave guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless; timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s and 40Gb/s high speed communication system. MT82 adopts low noise, narrow linewidth CW DFB laser as light source; LiNbO3 external modulator as signal modulation, no laser chirp, low dispersion distortion, high extinction ratio, Full-transparency operation mode. It can be applied in long distance and extra-long distance transmission after EDFA.

  • Automated Thermal Stress System

    ATSS Series - Thermotron Industries

    Thermotron's Automated Thermal Stress Systems (ATSS) facilitate extremely rapid product temperature change rates in a space-saving, self-contained design that accelerate a Thermal Stress test. Thermotron's ATSS chambers meet the latest MIL-STD 883E and MIL-STD 202F thermal shock specifications as well as JEDEC and IPC test methods. ATSS chambers are capable of the following: Rapid thermal shocking, Accelerated product stressing, Controlled thermal cycling in a self-contained, compact design. With separate hot and cold zones, the Automated Thermal Stress System was designed with a patented retractable product transfer carrier that makes full use of the available working volume in both temperature zones for increased product loading and throughput. The product transfer carrier reduces the overall height requirements of the chamber and is made as light as possible to minimize thermal loading restraints. Thermotron ATSS chambers can be used as part of most commercial reliability and quality control programs, helping to determine:

  • Vickers Hardness Tester

    Mitech Co., LTD.

    Digital vickers hardness tester, based on the principle that positive quadrangular pyramid diamond indenter presses the surface of the sample to produce indentation.By measuring the diagonal length of the indentation to achieve the measurement of the hardness of the material can be for small specimens, thin specimens, surface coating, heat treatment of the workpiece surface Vickers hardness test. With stable performance, strong structure, high reliability, simple operation, adopt digital display and high magnification optical measurement system, adjust the cold light source, photoelectric sensing technology and computer-aided means it has a powerful function. It is widely used in the fields of metal processing, electronics industry, mold parts, watch manufacturing, engineering quality inspection and so on. It is an ideal hardness tester for material research and testing.

  • OTDRs and Fault Locator

    AFL

    AFL optical time domain reflectometers (OTDRs) and fault locators are used to certify new fiber installations and locate faults in deployed fiber optic networks. OTDRs and fault locators are available for both multimode and single-mode networks, including FTTx PONs. OTDRs scan fiber optic networks from one end of the fiber, displaying a trace and reporting detected events such as splices, connectors, micro- or macro-bends and fiber end. Fiber length is reported along with location, loss and reflectance of detected events. Several OTDRs are available with an integrated visual fault locator (VFL), optical light source (OLS), and/or optical power meter (OPM). OTDR results can be saved and uploaded to PC for further analysis and/or archiving.

  • New Car Battery Tester

    Hangzhou Xun Anda Electrical Co., Ltd.

    1. Test application: 12V/6V batteries test and 12V Starting /Charging system test.2. Test battery type: regular liquid, AGM battery, GEL battery.3. CCA test range: 40~2000CCA (SAE).4. Voltage test range: 1.5-15V.5. Display SOH (state of health), SOC(state of charge).6. Test for multiple battery standards: SAE, DIN, EN, IEC, CA.7. Graphic LCD display with back light, LCD brightness adjustable.8. Multigle language operation: English, Chinese, Germany, French, Spanish.9. Intergrated thermal printer to print test reports.10. Thermal printer paper roll is 58mm width and 7.5m long.