Showing results: 2701 - 2715 of 3380 items found.
-
TP02 -
Hukseflux Thermal Sensors B.V.
TP02 is a probe that offers the possibility to perform a practical and fast measurement of the thermal conductivity (or thermal resistivity) of the medium in which it is inserted at the highest accuracy level. It works in compliance with the ASTM D 5334-00, D 5930-97 and IEEE 442-1981 standards. The standard TP02 probe has proven suitability in soils, thermal backfill materials, sediments, foodstuff, powders, sludges, paints, glues and various other materials. The Non-Steady-State Probe (NSSP) measurement method (also known as transient line source, thermal needle, hot needle, heat pulse- and hot wire technique) has the fundamental advantages that it is fast and absolute while the sample size is not critical. Hukseflux is specialised in NSSP design. Special models have been developed for in-situ field experiments. For permanent installation in soils, a dedicated model, TP01, is available. TP02 has been designed and tested in collaboration with the Applied Physics Group of Wageningen University.
-
T3110 -
COMET SYSTEM, s.r.o.
Programmable temperature and humidity transmitter is equipped with temperature and relative humidity sensors. Measured values are also converted to other humidity interpretation - dew point temperature, absolute humidity, specific humidity, mixing ratio or specific enthalpy. Degrees Celsius and Fahrenheit are user selectable. Transmitter contains a microprocessor based control circuitry in a durable plastic case with connection terminals and sensors in a filter with stainless steel mesh. Humidity transmitters is equipped with two galvanic isolated 4-20mA outputs. Configuration of outputs and output range are user adjustable. Large dual line LCD for simultaneous display of T+RH or other humidity interpretation is an advantage. Display is possible to switch off. Computerized design ensures temperature compensation of the humidity sensor and fail indication. State-of-the-art capacitive polymer sensor ensures excellent calibration long term stability, inertia against water and condensation. Transmitters are designed for use in non-aggressive environment.
-
SERIES 7000 -
Polatis, Inc.
The Polatis Series 7000 Network Optical Switch is the largest-capacity, highest-density, highest-performance and most reliable non-blocking all-optical matrix switch available in the industry. The Series 7000 384x384 all-optical circuit switch is designed to meet the most demanding applications with exceptionally low optical loss, compact size, and fast switching speeds. With support for Software-Defined Networks (SDNs) via embedded NETCONF and RESTCONF control interfaces, the Series 7000n can route time-critical traffic with very low-latency to enable new virtual cloud services in hybrid packet-optical data centers. The Series 7000n is the latest addition to the Polatis product line of optical switches and modules, creating the broadest portfolio available of dynamic fiber cross-connect solutions (up to 384x384), all built on the Polatis’ patented DirectLight® optical switching platform that has been proven in the most challenging data center, telecom and defense and test applications for over a decade.
-
8130A -
TSI Inc.
The Automated Filter Tester Model 8130A continues to be the best solution for testing particulate respirator filters, disposable filtering face pieces, and a wide assortment of filter media. The TSI filter testers have been used in quality control and manufacturing by leading filter and filter media manufacturers and test centers around the world for more than 20 years. Based on TSI's established model 8130, the world's most-used filter tester, model 8130A now offers higher sensitivity and resolution - up to 99.9999 percent efficiency - at a lower cost of ownership due to the new serviceable photometers inside. The model 8130A features a high degree of automation and self-diagnostics that greatly simplifies operation, increases throughput, and improves overall measurement performance. Whether looking for a stand-alone tester to check a few filters per day or need to integrate a tester in an automated, high-volume production line, the model 8130A is up to the challenge.
-
Bruker Daltonics
Discover new ways to apply mass spectrometry to today’s most pressing analytical challenges. Innovations such as Trapped Ion Mobility (TIMS), 10kHz scanning lasers for MALDI-MS Imaging that deliver true pixel fidelity (10 um spatial resolution), and eXtreme Resolution FTMS (XR) technology capable to reveal Isotopic Fine Structure (IFS) signatures are pushing scientific exploration to new heights. Our mass spectrometry solutions enable scientists to make breakthrough discoveries and gain deeper insights.Our industry leading software solutions such as SCiLs Lab for MS Imaging, FDA cleared microorganism reference library for the MALDI Biotyper, Biopharma Compass 2.0, and Toxtyper are examples our solutions doing the work for you. Bruker's product lines include the following technologies: FTMS, rapifleX MALDI-TOF/TOF, MALDI Biotyper Systems, timsTOF UHR-QTOF, Toxtyper, Triple Quadrupole, HDX Solution, ToxScreener, PesticideScreener
-
Giga-snaP™ -
Ironwood Electronics
Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapter line of products provide an inexpensive and reliable method for attaching BGA chips to target board. The product line consists of patented female sockets with machined pins epoxy over-molded into an assembly that matches a particular BGA pattern. The epoxy over-molded female BGA socket is soldered to a PCB using standard soldering methods. A corresponding male pin BGA adapter, to which the user attaches their BGA chip, is plugged into the female socket on the board thus interconnecting the chip and the system is ready to go. The SMT adapters have the same solder ball types as the chips they are emulating. These adapters have less than half of the insertion force of competitive adapters, shorter electrical path for highest speed, and can be solder reflowed numerous times. A complete description and drawings of Giga-snaP™ 0.75, 0.8, 1.0, and 1.27mm pitch BGA Surface Mount Feet Adapters can be found at the tables shown below.
-
Avionics Interface Technologies
To satisfy ARINC 615/615A data loader requirements in system engineering labs, avionics system manufacturing, and maintenance depot applications, AIT provides data loader software that can be used together with AIT’s full line of ARINC 429, ARINC 664, and Ethernet interface modules and integrated into a variety of host desktop PC systems and ATE environments. The F-SIM-LDR-615 software provides ARINC 615-3/4 data loader support and is compatible with all of AIT’s ARINC 429 interface modules. The F-SIM-LDR-615A software application provides ARINC 615A-1 /2/3 data loader support over Ethernet and ARINC 664 networks and is compatible with all of AIT’s ARINC 664/Ethernet interfaces modules. The F-SIM-LDR-615 and F-SIM-LDR-615A software products include both graphical user interface (GUI ) data loader applications and command line data loaders which are scriptable and can be called from shell scripts, batch files, and python for support of automated load operations.
-
FV-1500 -
Ono Sokki
FV-1500 High-speed F/V Converter is a frequency-to-voltage (current) converter that converts frequency signal proportional to rotation speed, moving speed, etc. into voltage signal.The FV-1500 is designed to accommodate the needs of high speed rotation measurement including rotating motors used in HV/EHV production lines etc. It also contributes to measure rising characteristics, very small fluctuation in steady rotation, and transient phenomena of flow speed with fast response.
-
NECTA S Series -
Alkeria Srl
NECTA S, the SWIR line-scan model in NECTA camera family, is capable of high-resolution acquisition in short-wave infrared bandwidth, ranging from 950 to 1700 nm. This new SWIR camera can reach up to 40kHz line rate with 14bit A/D converter: its high-speed USB3 interface, an advanced I/O, together with a compact and rugged aluminum case, make NECTA S suitable for most demanding machine vision applications.
-
KS-1600 -
Konstar Electric Industrial Co., Ltd
It is a dial instrument, and has the stable function and high reliability. It is driven by the battery. The instrument makes use of the indicator plate(102*79mm), thus displays clearly.This instrument can test the data of on-line capacitive resistance and on line impedance. It is an excellent instrument and an ideal tool for the people in labs, factory and household. When testing the mounted capacitor, it does net need to be completely out of power nor do the meter, and the meter can be testing continuously.
-
ScanArm -
FARO Technologies, Inc.
The FARO ScanArm combines all of the advantages of the FaroArm with a hand held laser scanner and is the perfect contact/non-contact measurement system. Unlike other scanning systems, the ScanArm’s hard probe and the Laser Line Probe can digitize interchangeably without having to remove either component. Users can accurately measure prismatic features with the hard probe, then laser scan sections requiring larger volumes of data — all in one simple tool.
-
F-16 -
TestVonics, Inc.
The primary function of the Air Data Test System (ADTS) is to perform testing and fault isolation of pneumatic-type Units Under Test (UUTs). To test a UUT, the operator connects the associated Line Replaceable Unit (LRU) Integrated Test Adapter (ITA) to the rackmount Avionics Intermediate Shop (AIS) test station. The operator connects the ADTS to the IAIS via an RS-232 Interface and then finally, connects the UUT to the ADTS using the supplied cables and hoses.
-
DTA-BERT -
ShinewayTech
DTA-BERT E1/Datacom Transmission Analyzer can perform E1 transmission performance test (BERT) and status monitoring on data link (V.35, V.24/RS232, RS449, RS530, X.21). Model T can also perform G.703-64K bit error test, PCM31/30 test and Jitter test. Featuring comprehensive functions, easy operation and compact design, DTA-BERT provides total solutions for E1 line analysis and maintenance.
-
PAS-F -
Intepro Systems
The Intepro PAS-F Series is a broad line of programmable three phase output regenerative utility grid simulator products. With power levels ranging from 45kVA up to 1.6MVA, the series is capable of testing the largest of dispersed energy inverters. The PAS-F combines utility grid simulation with regenerative bi-directional AC source controlled power that is capable to both source and sink full current from the equipment under test (EUT).
-
880 Series -
Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata 880 series video test instruments offer a wide variety of solutions for HDMI 1.3, DVI, DisplayPort 1.1 and analog video. There are several options (models) available depending on the digital interfaces and functions that are required for a particular application. The solutions supported by the 880 series include functional testing in the R&D environment, compliance testing, manufacturing testing for production lines and testing in military applications as well.
