Showing results: 766 - 780 of 850 items found.
-
Astronics Corporation
The TS 717 Test Set for ARINC 717 is a convenient, easy-to-use tool for test and maintenance of aircraft systems that are tied to the Digital Flight Data Recorder (DFDR). The compact interface/cable hardware is conveniently stored in a rugged carrying case for easy transport and quick deployment.The webFLT™ is a wireless functional tester for aircraft systems using the Digital Flight Data Recorder ARINC 717 bus. It connects directly to the aircraft system test plug and transfers data to the test computer via an 802.11 b/g wireless link, eliminating cabling in the crowded cockpit that can be tripped over or damaged.
-
M8132A -
Keysight Technologies
The M8132A is a powerful digital signal processing module featuring two customers accessible Xilinx Ultrascale+ FPGAs, four optical data interfaces (ODI) running at up to 160 Gb/s in+out each, and a PCIe Gen3 x8 link to the AXIe backplane. In addition, the module provides a trigger input and output, synchronization input and outputs for deterministic latency between compatible digitizers and AWG modules as well as a 10-general purpose I/O pins. The M8132A is part of Keysight’s Wideband Solution Platform that consists of a portfolio of compatible instruments, including digitizer, arbitrary waveform generator, digital signal processor and storage modules.
-
Optoplex Corporation
Targeting for the next-generation 40Gb/s system based on advanced optical differential phase shift keying (DPSK) demodulation, Optoplex’s 40Gb/s Integrated DPSK Receiver (DPSK Rx) demodulates an incoming DPSK optical signal into a pair of differentially (amplitude) modulated RF outputs at data rate up to 43Gb/s in a compact package. Phase modulated optical signals offer much better dispersion performance compared with traditional amplitude modulated counterparts because the carrier light stays on all the time so that the intensity-dependent nonlinear effects in the transmission link are avoided, resulting in longer transmission distances.
-
VX1725 / VX1725S -
CAEN S.p.A.
The VX1725S family comes in a VME64X form factor, with 16/8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces. The VX1725S is a digitizer capable of recording waveforms along with performing advanced algorithms for online digital pulse processing (DPP). Utilizing DPP Firmware, users can acquire quantitative physical parameters (Integrated Charge, Pulse Shape Discrimination with very fine time resolution, Pulse Height Analysis) as well as read out waveforms with automatic pulse identification and baseline suppression on channel basis (Zero-Length Encoding and Dynamic Acquisition Window).
-
T-BERD/MTS-5882 -
Viavi Solutions Inc.
The T-BERD/MTS-5882 is extremely versatile, enabling the cell site technician to address all key tests with one, lightweight, handheld tester; including: Fiber Inspection: Dirty fiber connections are the #1 cause of network downtime. Microwave back-haul: The majority of microwave backhaul links around the world are still microwave. Enhanced Cable Diagnostics: Environmental factors can damage the CAT X shielded twisted pair cable connecting the microwave antenna. Fronthaul: Avoid dangerous tower climbs with CPRI testing including BERT, PIM detection, MIMO diversity, RET, and VSWR. Backhaul: In addition to packet testing across error-prone microwave hops.
-
UTEC 430 -
Radian Research, Inc.
The UTEC 430 is the first Portable Meter Test Kit to support both the Radian Dytronic (RD) and the installed base of Radian Metronic (RM) reference standards. The ability to support both reference standards makes the 430 the ideal budgetary solution for traditional on-site meter testing using Phantom Load current sourcing. Do not let its compactness fool you, the UTEC 430 has three 30 Amp current output elements for performing single-phase or three-phase meter testing. When each element is combined using the optional open link cable harness, the UTEC 430 can source up to 90 Amps.
-
Macom Technology Solutions Holdings Inc.
MACOM’s OTN Framer/Mapper/FEC family products offer complete portfolio of solutions for 10G, 40G and 100G optical transport networks. They are ideal for high-capacity Carrier Ethernet router/switches, Packet Optical Transport systems and DWDM Transport systems. The OTN framer devices integrate high performance Serdes I/O to allow seamless connection to optical and copper modules. The provisional Tri-FEC integration supports G.709 standard RS-FEC as well as high coding gain G.975.1 I.4 EFEC and I.7 UFEC to improve optical link performance, achieve longer reach and offer interoperability flexibility.
-
F-SIM-A664 -
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 664 Interfaces - Simulate Multiple ARINC 664 End Systems Simultaneously - Full definition of input/output VLs, input/output Sampling and Queuing message ports, & TFTP Clients & Servers - Capture & Analyze Data from Multiple Virtual Links (VLs) - Live display showing all of the detected ARINC 664 VLs and message counts - Live displays showing all of the detected source and destination message (UDP) ports - Record network data to PCAPNG for use with Wireshark - Replay Previously Captured Bus Data - Also Supports MIL-STD-1553, ARINC 429 & Data Load operations
-
Hilkar
Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.
-
Keysight Technologies
From simple connection to programmatic control, Keysight provides all the software tools necessary to accelerate the process. Compatible with the most common interfaces (GPIB, RS-232, LAN, PXI, and USB), Keysight's IO Libraries will quickly discover and configure instruments. Once the connection is established, Command Expert can control instruments using IVI-COM drivers and Standard Commands for Programmable Instruments (SCPI) Command Sets. Instrument drivers provide a higher-level and more abstract view of the instrument. IntuiLink software links an instrument to some PC applications. BenchVue software offers multiple instrument measurement visibility and data capture from a PC or mobile device with no programming.
-
213 HVD~226 HVD -
Standard Electric Works Co., Ltd
● Excellent shock resistance.● Rugged nylon moulding.● Auto on (when voltage detected).● Excellent drop resistance.● Good vibration resistance.● Loud sound alarm indication.● Built-in proving and self-test circuit.● High bright color-coded LEDS.● Works from standard 9V battery.● Interchangeable contact electrode.● Use in all whether conditions.● Compatible with all link sticks.● Lightweight, robust & compact.● Models available from 11kV to 132kV.● Suitable for indoor and outdoor use.● Self(auto on) or manual arming.● Easy access to batteries.● Customized threshold on demand.● Auto off (if no voltage detected).● Waterproof design, protection class : IP65.
-
OPT 80 -
Unaohm Start S.r.l.
Calibrated measurement of the optical power of satellite and terrestrial TV signals distributed in optical fiber Calculation of optical signal losses on distribution Measurement of digital parameters (BER - MER - NM etc.) of optical signals converted into RF Visualization of optical carriers in RF Field Metric Spectrum Analyzer Power Meter Optical Field Meter Display Optical RF Power Supply Line Link Meter (LNB power supply ) Optical LNB power supply 13V 500mA with short circuit and overload managementAcquisition of optical measurements using the field meter Data Logger Option: certification of the OPT80 calibration and optical power measurements
-
TD6 TestStand Software -
Qmax Test Technologies Pvt. Ltd.
The TD6 TestStand will enable the users to sequence and execute their own test programs. The user can browse his/her test program and add it to the TD6 TestStand component. The test program can either be in the form of DLL ( Dynamic Link Library ) or EXE ( Executable ). And, the user can add any number of steps. As of now, we will support only the .Net based test programs. Each and every individual assembly or exe added in the TestStand component will be considered as a single step. All such steps on the whole added in the TestStand component will be considered as 'Sequence'. The same is priced at Rs. 8,42,520.00 plus GST @18% extra. For further details, pls contact sales@qmaxtest.com
-
FAB114 -
Axiomtek Co., Ltd.
The FAB114 has a PICMG 1.3 CPU card slot, one PCI Express x16 slot, three PCI Express x1 slots and a total of eight 32bit/33MHz PCI slots. The onboard 24-pin ATX power connector and 8-pin connector for thermal detected board are featured. Through one PCIe x16 link, this PICMG 1.3 backplane maximize the performance of high-end PCI Express graphics and video cards. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB114 is perfect fit for AXIOMTEK's SHB100 and SHB110. AXIOMTEK also offers versatile 4U industrial chassis specially design for the FAB114, such as the AX61400, AX6156 series and AX61491.
-
VP62105 -
LinkedHope Intelligent Technologies Co.,Ltd.
VP62105 supports up to 3615QE, an Intel® 4-core processor. The 3rd generation Intel® Core™ i3/i5/i7 processors have a completely new microarchitecture, enabling small-sized designs to be created with unmatched computing power, graphics performance and energy efficiency on a small footprint.VP62105 provides 4 Serial RapidIO (SRIO) x4 links for VPX Data Plane communication, 2 PCI express x8 channel for VPX Expansion Plane communication and 4 Gigabit Ethernet for VPX Control Plane communication. The rich data interchange options enable potential customers a much easier integration path for box level or system level solution designs.
