Showing results: 856 - 870 of 2342 items found.
-
Elmeasure India Pvt. Ltd
Multiple branches of load can be monitored togetherCan group the device as 3 phase load and single phase loadFaster communication through RS485 port (Modbus protocol)Simultaneous sampling of Volts and AmpsAccuracy Class 1.0 as per IEC 62053-21 & Class 0.5 as per IEC 62053-22 StandardsDisplays more than 25 parameters
-
JFE Advantech Co., Ltd.
This weigher can be easily installed in a hopper for faster construction by adopting our prominent load cells with built-in constrainer.
-
D series, -
Mors Smitt Group
Heavy duty relays for demanding applications, switching of AC&DC voltages, resistive and/or inductive loads.
-
-
VOL-PBE -
Lisun Electronics Inc.
• EMI Receiver equipped with voltage probe can test disturbance voltage from load terminals or control terminals
-
MRC ltd.
The impact tester is used for testing the impact resistance of materials, to determine their quality under dynamic load conditions.
-
-
Interface Inc.
Multi Axis Load Cell are designed and manufactured by Interface to measure a multiple of forces and/or moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the other forces or moments - when installed and used according to specifications.
-
JB104SS -
Interface Inc.
The JB104SS junction box model is designed to connect and trim up to four load cells per board. It may also be used in combination with additional juction boxes through the use dof an expansion port on the main board to connect multiple junction boxes thus allowing the summing of more than four load cells.
-
FS-409 -
PINTEK Electronics
*OSCILIOSCOPE: 40MHz Dual Trace,Dual Trigger. 1mV Sensitivity. 10ns Resolution.*FUNCTION GENERATOR: 0.5Hz~5MHz Frequence. Sine,Square,Triangle,3 waveforms. Max output:20 Vp-p(No Load),10 Vp-p(50O Load). TTL Synchronous Output.*COUNTER: 5 Digits 0.36" Red LED Display.
-
Instron
RS LabSite® modulogic is a comprehensive and adaptable software suite conceived for introducing service loads into individual components or complete vehicles, or performing calculations within the framework of Virtual Prototyping (standardized loadsequences, virtual generation of load data). This enables you to stay in full control of all tasks that follow the acquisition of measurement data in the proving ground.
-
Laurel Electronics, Inc
Equipped with a DC or load cell signal conditioner, this Laureate offers special firmware for scale / weighing applications: two tare functions; count by 1, 2, 5, 10, 20, 50 or 100; auto-zero function; setpoint offset, and dummy right-hand zero for display to 999,990. Built-in excitation for up to four 350-ohm load cells in parallel.
-
SKS-1132GTB -
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
SKS-1120GTB -
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.
-
SKS-1120GTA -
Shanghai Sanki Electronic Industries Co., Ltd.
The cycle drop simulator is used to reproduce the voltage fluctuation phenomenon of commercial power supplies. Simulate the grid voltage drop and short-term interruption caused by the accident or the sudden change of the large load in the low-voltage power grid, or the grid voltage change caused by the continuous change of the load. Used to evaluate the performance of the equipment under these voltage changes.