Showing results: 1351 - 1365 of 2327 items found.
-
MM-6 -
Sutter Instrument Company
The MM-6 micropositioner is light weight, accurate, compact device designed to eliminate many research and design problems, especially in the case of space limitations. Hardened steel precision pre-loaded ball bearing slides and high resolution thumbscrew movement assure smooth motion, precision, and excellent load bearing capacity.
-
Finna Sensors
The transverse sawmill meter sorts pieces into four moisture groups with similar drying characteristics by assigning a dry-ability index number. This critical first step in end-to-end moisture control improves kiln performance by reducing aggregate standard deviation and total drying time when compared to unsorted loads.
-
MODEL PDS-6000 -
TEK-VAC INDUSTRIES Inc.
One centrally located robot with four access ports. Four process chambers, one central loadlock, and one clean room load lock. Two 330 liter/second turbomolecular pump serving all process chambers. Options of 104 CFM Roots Blowers each backed by a 27 CFM rotary vane pumps.
-
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
PXG-M Series -
TDK-Lambda Corp.
*Industry Standard 1.6" x 1" Footprint*9-36, 18-75 Vdc Inputs*5, 12, 15, 24, ±5, ±12, ±15 Vdc Outputs*5000kVac Input to Output Isolation*-40 to +105 °C Case Temperature*Medical and Industrial Safety Certifications*Low No Load Power Consumption
-
PXD-M Series -
TDK-Lambda Corp.
*Industry Standard 2" x 1" Footprint*9-36, 18-75 Vdc Inputs*5, 12, 15, 24, ±5, ±12, ±15 Vdc Outputs*5000kVac Input to Output Isolation*-40 to +105 °C Case Temperature*Medical and Industrial Safety Certifications*Low No Load Power Consumption
-
KT-2817A -
KILTER ELECTRONIC CO.,LTD
240*64 dot-matrix large graphics LCD displayDendriform operation structure with softkeysOpen/Short/Load correction functions2 different signal source output impedances with 30Ω、100ΩTest speed up to 32times/secList sweep functionMeasuring with 9 ranges,ensuring high accuracy,stability and identity10 groups setup for store & recall
-
F-SIM-LDR-615A -
Avionics Interface Technologies
The F-SIM-LDR-615A software application is an ARINC 615A data loader tool which is compatible with AIT’s family of ARINC 664 interface modules and standard LAN interfaces available on most PC’s. The F-SIM-LDR-615A application supports ARINC 615A load operations over Ethernet and ARINC 664 networks.
-
ZPS-1600B -
CoolMax Technology Inc.
80Plus Silver Certified provides typical 88% efficiency at 50% of max load. The ZPS-1600B can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in 16 8-pin PCI-Express graphic card connector offering further upgradability.
-
ST Series -
Unholtz-Dickie Corporation
The ST Series Slip Table Assembly is one of three base configurations offered by Unholtz-Dickie for its vibration test systems. It is ideally suited for sequential 3-axis test capability with minimized cross axis response; for testing heavy, oversized, or non-symmetrical loads; and for products where orientation with respect to gravity is necessary.
-
Aero Nav Laboratories, Inc.
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
National Technical Systems
Flexural Strength Testing is used to determine the flex or bending properties of a material. Sometimes referred to as a transverse beam test, it involves placing a sample between two points or supports and initiating a load using a third point or with two points which are respectively called 3-Point Bend and 4-Point Bend testing.
-
Carl E. Holmes Company
Delta DC Rectifiers are used by original equipment manufacturers to build On-Site Sodium Hypochlorite Generator Systems. These power supplies are generally operated at full load for 24/7 operations at high temperatures. Hence, these power supplies must be extremely rugged and must be de-rated significantly to achieve long operating life.
-
Exosens Group
In Gamma detectors, the gamma radiations produce electrons by interacting with the cathode material and the filling gas.These electrons ionize the gas and the charge carriers are collected by the electrodes. The resulting anode pulse is detected by a load circuit. The primary electrons are created by several interaction mechanisms:- Photoelectric effect- Compton scattering- Pair production
-
6450 -
The Eastern Specialty Company
The TESCO CT/PT Bus-Bar Safety Protector (Catalog No. 6450) has been developed to assist in the safe disconnect of a hot sequenced current transformer. After service is disconnected, the TESCO CT/PT Bus-Bar Safety Protector is slid over the bus-bar of the load side of the transformer and prevents accidental connection and/or arcing.