Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Ltd.
product
PXI/PXIe Microwave Transfer Switch, Single, 40 GHz, 50 Ω, SMA-2.9, Failsafe, Remote Mount
42-782B-541-E
The 40-782B-541-E (PXI) and 42-782B-541-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 40 GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
product
Quad M Module Carrier
DP-cPCI-5112
DP-cPCI-5112 provides a compact high performance cPCI bus gateway to four ANSI approved M-Module Interfaces. This is a non-intelligent 6U form factor M-Module Carrier board. The DP-cPCI-5112 allows a flexible I/O solutions to be implemented in the carrier board. The M-Module carrier board occupies single slot in a CompactPCI system. Different mix and match of various I/O solutions will simplify the job for system integrators.
-
product
PCIe to SD 3.0 M.2 Module
The M.2 module is based on Artix-7 FPGA that provides bridging features between PCIe and SD3.0 units to validate different memory densities of micro-SD card. For host processor communication, the module is designed with 2-Lane PCIe Gen 2.0 interfaces. The module presents compact design, flexibility, and consumes low power. Since PCIe is backward compatible with the earlier version the user can integrate into existing systems with ease. The interface towards the SD card is realized by the SD protocol implemented in the FPGA.
-
product
Dual M.2 Card SSD Mezzanine Module
C48-1-M2
C48-M2 connects to the mezzanine expansion connector HSE of the CompactPCI® CPU carrier. 4HP envelope of the CPU carrier board, but can also be used on some mezzanine side cards, for an 8HP or 12HP total front panel width assembly.
-
product
PXIe-8267, 4 TB, M.2, PXI Data Storage Module
785308-01
PXIe, 4 TB, M.2, PXI Data Storage Module - The PXIe-8267 PXI Express high-speed data storage module features large-capacity, high-throughput storage in a single PXI Express slot. With M.2 solid-state drives, the PXIe-8267 is ideal for stream-to-disk or stream-from-disk applications requiring sustained, reliable data throughput such as high-speed signal intelligence, RF record and playback, and multi-sensor data acquisitions systems.
-
product
Squid PCI Express Carrier Boards for M.2 SSD Modules
SKU-064-2X
Flexible x1 PCI Express to 3 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows you to connect up to three MiniPCI Express add-in boards to the standard motherboard PCI Express connector.Splitter includes 3 MiniPCI Express adapter boards, x1 PCI Express host board and 3 flat PCI Express Cables.
-
product
Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
Amfeltec Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
-
product
Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
Amfeltec Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
-
product
Intel® Wireless-AC 9260 Wi-Fi + Bluetooth M.2 2230 Module Card with Cables and Antenna Kit
EWK-M2-AC9260 Series
Intel® Wireless-AC 9260 Wi-Fi + Bluetooth M.2 2230 module card with cables and antenna kit
-
product
Intel® Wireless-AC 9260 Wi-Fi + Bluetooth M.2 2230 Module Card with Cables and Antenna Kit
EWK-M2-AC9260
- Bluetooth 5.1- IEEE 802.11ac wave 2 (Wi-Fi 5)- Operating Temperature : 0°C to 70°C (-40°C to 75°C extended)- Compact M.2 2230, A/E key form factor with cable and antenna kit to support flexible installation
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 2 M.2 SSD Modules
SKU-086-32
PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 2 M.2 PCI Express SSD modules.PCI Express Carrier board is one-slot-wide, half-height and it compliant with PCI Express Specification 3.0 and M.2 Specification 1.1.
-
product
Squid Carrier Board™ Family PCI Express Gen 2 Carrier Board for 4 PCIe M.2 SSD Modules
SKU-086-01
The Squid PCI Express Carrier board for M.2 SSD modules is the second product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 4 M.2 PCI Express SSD modules. This product is recommended for use in Mac Pro Desktop computers.
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for One M.2 PCIe SSD Module
SKU-086-31
The Squid PCI Express Carrier board for M.2 SSD module is the smallest carrier board on the market. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows vertical installation in any 1U servers or appliances.
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 4 M.2 PCIe SSD Modules
SKU-086-34
PCIe Carrier board was designed to expand modern motherboards that have PCIe interface. It allows connection of up to 4 M.2 PCI Express SSD modules.PCIe Carrier board is one-slot-wide, half-height and it compliant with PCIe Specification 3.0 and M.2 Specification 1.1.
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 4 M.2 PCIe SSD Modules
SKU-086-B4
B-series PCI Express Gen3 Carrier board was designed as a cost-effective storage solution for the systems that are using a motherboard with PCI Express bifurcation support. Such motherboards can be configured in the BIOS to split x16 PCI interface to four PCI Express interfaces by utilizing the following PCIe lanes:- x4 PCI Express interface 1: lanes 0,1,2,3 from x16 PCIe interface;- x4 PCI Express interface 2: lanes 4,5,6,7 from x16 PCIe interface;- x4 PCI Express interface 3: lanes 8,9,10,11 from x16 PCIe interface;- x4 PCI Express interface 4: lanes 12,13, 14, 15, from x16 PCIe interface;
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for six M.2 or NGSFF (NF1) PCIe SSD Modules
SKU-086-36
This Squid PCIe Carrier board can support up to six M.2 or NGSFF (NF1) PCIe SSD (solid state drive) modules, with M-key. Supported module dimensions are 2280 or 22110 in length, and a width of up to 32 mm. SSD modules of any capacity may be used, from any vendor, and in any combination.
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for two M.2 or NGSFF (NF1) PCIe SSD Modules
SKU-086-32e
This Squid PCIe Carrier board can support up to two M.2 or NGSFF (NF1) PCIe SSD (solid state drive) modules, with M-key. Supported module dimensions are 2230, 2242, 2260,2280 or 22110 in length, and a width of up to 32 mm. SSD modules of any capacity may be used, from any vendor, and in any combination.
-
product
IO60-DIO48 Module
IO60-DIO48
WINSYSTEMS’ IO60-DIO48 Module adds GPIO to embedded systems with IO60 expansion featuring 48 GPIO (General Purpose Input-Output) tolerant to 30 V DC. The SPI interface is implemented through the MACH XO2 SPI-slave EFB (Embedded Function Block) interface. Each bit of each port is implemented as a bi-directional tristate driver. Each bit of each port can also be configured and enabled to detect rising and/or falling edge events and generate a system interrupt.
-
product
PXI Solid State Switch Module, 3xSPST, 10 A
40-182A-012
The 40-182A-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
PXI Solid-State Switch Module, 3xSPST, 1.5 A, 400 V
40-185A-002
The 40-185A-002 has 3-off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions.. Each SPST switch uses a fully isolated solid-state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
product
High Density Switching PXI Card
GX6338
The GX6338 is a low cost 6U switching card with 114 individual low level SPST Form A relays capable of switching 0.5 A at 200 VDC. The GX6338 is ideal for applications requiring high density switching.
-
product
PXI 4 x Changeover Switch 2.5GHz, 50 SMB
40-710-514
This RF switching card has a bank of four individual high performance RF changeover switches (50 or 75 Ohm, Bi-directional) with very low insertion loss, suitable for handling signals up to 2.5GHz. Applications include aerial switching, routing high frequency signals into oscilloscopes and analyzers.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 50GHz, 50Ω, SMA-2.4
40-782B-551
The 40-782B-551 (PXI) and 42-782B-551 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 50GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 40GHz, 50Ω, SMA-2.9
40-782B-541
The 40-782B-541 (PXI) and 42-782B-541 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 40GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 26.5GHz, 50Ω, SMA
40-782B-531
The 40-782B-531 (PXI) and 42-782B-531 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 26.5GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 18GHz, 50Ω, SMA
40-782B-521
The 40-782B-521 (PXI) and 42-782B-521 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 18GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
PXI/PXIe RF Switch, Octal SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-004
The 40-880B-004 (PXI) and 42-880B-004 are octal SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range have automatic termination of unused signals and are available as a dual switch in a 1-slot, a quad switch in 2-slots or hex and octal switches in 3-slots.
-
product
PXI/PXIe RF Switch, Quad SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-002
The 40-880B-002 (PXI) and 42-880B-002 (PXIe) are quad SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range has automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in two slots or hex and octal switches in three slots.
-
product
PXI/PXIe RF Switch, Dual SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-001
The 40-880B-001 (PXI) and 42-880B-001 (PXIe) are dual SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range has automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in a two slots or hex and octal switches in three slots.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode
40-860A-332-HI
The 40/42-860A-332-HI is a PXI/PXIe triple insert/bypass switch with MU connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass
40-860A-432
The 40/42-860A-432 is a PXI/PXIe triple insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.