Showing results: 3346 - 3360 of 4205 items found.
-
33900 -
S & G Tool Aid Corp
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
Intego GmbH
Intego's knowhow even makes it possible to identify challenging defects that may be located under the surface. One system is the inspection of chips by means of lock-in thermography, which visually represents the IR radiation intensity signal of electronics. Special lasers and flash lamps generate a very short heat impulse (10 ms) on the chip, which generates a measurable heat flow. In most cases, a resolution of < 1 μm can be achieved.
-
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
RDP-20C -
TEGAM Inc.
TEGAM''s Humitran duct probes provide a reliable, accurate, and low cost method for monitoring relative humidity plus temperature. Solid state sensors supply excellent sensitivity, fast response and long term stability. Simple hook up and linearized output permit interfacing with most display or control devices. Model RDP-20C outputs a 4-20 mA current loop for long virtually unlimited cable distances.
-
192 -
Electronic Specialties Inc.
Relay Buddy 12/24 is a quick go / no-go tester for the most common automotive relays. This new version Relay Buddy tests both 12 and 24 volt relays. If the relay fails the test, 3 different trouble codes will advise you of the possible causes for the failed relay. The red LED will flash once, twice or three times to indicate the problem. Trouble code definitions are printed on the back of the tester for your convenience.
-
PCE Instruments
A sound level meter is a measuring instrument used to assess noise or sound levels by measuring sound pressure. Often referred to as a sound pressure level (SPL) meter, decibel (dB) meter, noise meter or noise dosimeter, asound level meter uses a microphone to capture sound. The sound is then evaluated within the sound level meter and acoustic measurement values are shown on the display of the sound level meter. The most common unit of acoustic measurement for sound is the decibel (dB); however, some sound level meter devices also determine the equivalent continuous sound level (Leq) and other acoustic parameters. With a portable sound level meter, industrial hygiene and workplace safety professionals can measure sound levels in multiple locations to ensure environmental conditions fall within recommended exposure limits (RELs). Some sound level meter devices can be permanently installed for continuous monitoring of sound levels at a work or job site. PCE sound level meter products are lightweight, easy-to-use and manufactured in accordance with the highest industrial standards.
-
STT-ESD-2005 -
Beijing KeHuan Century EMC Technology Co,.LTD
Is a tester that meets the requirements of IEC61000-4-2 and GB/T17626.2. Its maximum electrostatic discharge voltage can reach 30kV, covering the electrostatic voltage requirements in the standard (the electrostatic voltage requirement for the fourth level of air gap discharge is 15kV), and it is suitable for more application fields and the requirements of future new standards. Therefore, the ESD-2005 electrostatic discharge generator can be used for most electrical and electronic equipment electrostatic discharge tests, and can ensure the comparability and reproducibility of the test.
-
Wuhan Sunma Technology Co., Ltd.
Passive Optical Components are the foundation stone of WDM Passive Optical Network (PON). Besides MUX/DEMUX and splitters, SunmaFiber also provides other passive optical components such as attenuators, circulators, collimators, and isolators etc. In addition, we offer Customized Service that products with various parameters can be designed to meet different requirements. With very high performance but lowest prices on the market, our passive optical components can be the most cost-effective solution for modern PON systems.
-
T1000-37 -
Tesuto Systems
T1000-37 breakout box is our most versatile model, using dual 37 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 74 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
CIRCOFLUX Product Family -
Foerster Instruments, Incorporated
The CIRCOFLUX test system is used for the non-destructive surface testing of ferromagnetic steel bars using the magnetic flux leakage method in accordance with standard EN 10221. This method is the most sensitive surface testing method for longitudinal, crack-like defects in hot-rolled ferromagnetic steel bars. The CIRCOFLUX sensor system therefore replaces subjective testing methods such as the magnetic powder test (magnetic crack detection) and visual checks, which are difficult to document and reproduce.
-
SEP/SIP -
Nihon Denji Sokki Co., Ltd
There are analog phase control type DC power supply type and digital control type inverter energy saving type. We provide the most suitable equipment according to the current capacity and cycle time.If the "start command" is executed from the existing molding equipment, each mode of "alignment-pause-demagnetization" is continuously operated by the program inside the instrument. It is also possible to share an emergency stop signal and output an output current abnormality signal.
-
IT-25B -
Clinton Instrument Company
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
Conrad Braam
This protocol simulator started one weekend as a test program while developing a SCADA/HMI with modbus RTU and TCP/IP and afterward came in useful testing an embedded gnu-Linux device too. It has worked so well for me, I decided to put a nice GUI onto it and release it for free. The modbus protocol, also called open-mbus is implemented in many process control and monitoring devices, while most SCADA or HMI systems have a driver.
-
AQUADX Upgrade Kit -
CDx, Inc.
The AquaDx hand held water quality tester is for anyone who has ever been concerned about the quality of their well water or drinking water, and wants to get their water tested. AquaDx will test for a broader range of chemicals in water than most water testing kits and works with water testing labs and technology developers to make sure you have access to water testing services to check for the safety of your drinking water.
-
SiteX CP160D -
Teledyne ICM
The CP160D is the lightest and most compact generator of the CPSERIES. Featuring a built-in Beryllium window, it is the perfect generator for the inspection of light alloys such as aluminum, magnesium or fiber based materials like glass and carbon, as well as the greater thickness of steel. In fact, with its penetration capacity that is capable of reaching up to 37 mm of steel, the CP160D is able to execute many different types of NDT tasks without the need to ever have to add extra accessories.
