Filter Results By:
Products
Applications
Manufacturers
Magnetic Field
an force around magnets, electric current and atomic orbits.
See Also: Magnetic, Magnetic Test, Magnetic Head, Magnetic Susceptibility, Magnetic Flux, Magnetic Stripe, Magnetic Permeability, H-field, Magnetic Field Mapping, Magnetic Field Meters, Magnetic Field Probes, Magnetic Field Sensors, Magnetic Field Test, Helmholtz Coils
-
product
Portable Digital Tesla Meter
HT20
This instrument is convenient for operator to measure magneticinduction of DC magnetic field accurately. It is characterized by its wide range, clear display of LCD, and indefectible structure of sensor.A piece of 9V dry battery, which acts as its power supply, can servefor 4 hours continuously. Meanwhile, regulated power supply (enclosed) is available to 220VAC.
-
product
Test Fixture, Shielding Effectiveness
EM-2108 | 1.5 GHz – 10 GHz
The EM-2108 is a standard test fixture for evaluation of the electromagnetic shielding effectiveness (SE) of planar materials. The fixture is a section of coaxial transmission line broken to allow the insertion of planar test materials. Although ASTM D4935-10 is currently limited to an upper frequency of 1.5 GHz, the EM-2108 meets and complies fully with both the impedance and SE requirements called out in ASTM test method D4935-10 up to 10 GHz. These results are shown in Figures 1 & 2. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred.
-
product
Electrodynamic Velocity Pickup
The principle of Reciprocal Pendulum type Pickup is to induce voltage by reciprocal motion of the seismic mass with a coil in the magnetic field being suspended by a diaphragm or coil spring.. Because of its High Sensitivity and Advanced Linearity, it is suitable for detection of malfunction or deterioration of rotational machineries. Due to its structure, mounting should be done carefully for its direction or angle.
-
product
Linear Hall Sensor
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
product
Primary Cable Fault Locating
Directional Impulse Detector
The Directional Impulse Detector ( D.I.D.) is a compact handheld detector used to locate primary cable faults by sensing the magnetic field generated by the current pulse from a high voltage discharge device (thumper). A meter deflection indicates the intensity of the received signal. No deflection indicates that you have walked beyond the fault or away from the cable.
-
product
Zero Gauss Chamber
Measuring station for reproducible and location-independent measuring results for quality assurance, eg B. for cross-company supply chainsMeasurements of residual magnetism on ferromagnetic components are no longer significantly falsified by ambient magnetic fields induced in the object passive shielding, no power consumption and maintenance-free defined measuring station, good measuring room accessibility Platform in a robust design
-
product
Gaussmeter
GM2
The Model GM2 Measures the strength and polarity of magnetic field up to 30kG when using a standard probes, or 800 gauss (resolution 0.01 gauss) if an HS probe is used. Functions include DC, AC and peak hold along with a user-adjustable alarm which has three modes of operation. DC background field can be subtracted out either by pressing "Relative Zero" or by manually adjusting the offset. The meter includes battery, AC adapter analog output jack and calibration certificate. If a standard probe is used, resolution is 0.1 gauss up to 19,999.9 gauss, which is stronger than the field of any permanent magnet. This 5 digit display allows measurement of tiny difference in strong fields. Above 20kG the meter autoranges to a 30kG range.
-
product
MARATON Moderate HE
MARATON is a family of MAgnetic field and RAdiation TOleraNt power supplies developed for CERN LHC. MARATON MHE represents a 12 channel low-voltage power supply for installation in a moderate hostile environment with integrated CANbus remote monitoring and control interface. Voltages, currents, temperatures and output power are controlled by the internal processor and illegal modes as well as failure will be detected.
-
product
Electromagnetic (EM) Speed Log System
AGILOG 2
Aeronautical & General Instruments Ltd.
AGILOG 2 is based on the well-established electromagnetic principle that a voltage is induced in a conductor by a moving magnetic field. By using the sea water as a conductor, an output is generated as the vessel progresses. Electromagnetic speed measurement is passive in operation and therefore particularly suitable for use in submarines and warships. The EM technology provides reliable and robust speed availability when compared to some alternative technologies.
-
product
Miniature Single-Stage Isolators – 780nm And 852nm
AOSense is excited to offer free-space optical isolators at 780 nm and 852 nm. The innovative, small package size enables integration into compact laser sources and amplifiers without sacrificing transmission efficiency. The low external magnetic field enables the isolator to tightly integrate into systems with high magnetic-field sensitivity such as atomic spectrometers, magnetometers, clocks, and cold-atom devices.
-
product
Cryogenic Temperature Sensors
Interchangeable Rox™
Ruthenium oxide temperature sensors are thick-film resistors, with most models suitable for use in magnetic field applications. These composite sensors consist of bismuth ruthenate, ruthenium oxides, binders, and other compounds that allow them to obtain the necessary temperature and resistance characteristics. Each Lake Shore Rox™ model adheres to a single resistance versus temperature curve.
-
product
Zero Gauss Chamber
ZGC
The model ZGC zero gauss chamber reduces the environmental magnetic field (Earth field) to near zero inside the chamber. Any gaussmeter probe which is less than 9.4 mm or 0.370" diameter can be placed inside. The meter is then "zeroed", which means that it will read zero whenever the probe is subsequently placed in zero field. By using a zero gauss chamber, any offset error is therefore eliminated. The model ZGC is unique in that it contains a degausser (demagnetizer). This is situated between the inner and outer mu-metal shields. When the degauss button is pressed, any accidental magnetization of the chamber, no matter how strong, is erased. Accidental magnetization is a major problem with most zero gauss chambers and it has limited their use. If a magnet comes too close, the chamber will become "permanently" magnetized and will have an internal field that is typically 0.2 to 0.5 gauss. The chamber must then be degaussed because the Earth field is also around 0.5 gauss, so a magnetized zero gauss chamber will not significantly reduce the field.
-
product
Mini AC Leakage Current Clamp Tester
M-100+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・18mmφCT window and ultra compact size.・Least affection from the external magnetic field.・The special alloy is used for core material that resists the rust over long period of use and ensures stable,high accurate measurements with very slight influence from aging.
-
product
Magnetic Stripe Test Cards
Test Limit Cards (and tickets) are nominally encoded to ISO standards BUT WITH specific parameters deliberately set to predetermined levels, which can be inside or outside the ISO limits. The Test Limit Cards are designed for use by Test\Inspection Departments, Field Service Engineers, Reader \ Encoder Development Engineers to check and confirm proper operation of magnetic stripe reading equipment (e.g. ATMs and POS).
-
product
Single Channel Signal Conditioner
SAM-3
Macintyre Electronic Design Associa
The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.
-
product
Soft Magnetic Tester
Model SMT-700
KJS Associates/Magnetic Instrumentation offers the Model SMT-700 computer-automated magnetic test station for measuring the DC and AC magnetization curves, coercive field strength, and core-loss characteristics of magnetically soft materials, including: Si-Fe, Fe-Co, Fe, stainless steel, Ni-Fe alloys, soft ferrites and others. This modern line of laboratory instruments is designed specifically for accuracy, reliability, and ease-of-use.
-
product
Miniature Dual-Stage Isolators
780nm And 852nm
AOSense offers dual-stage, free-space optical isolators at 780 nm and 852 nm for enhanced isolation. The innovative, small package size enables integration into compact laser sources and amplifiers without sacrificing transmission efficiency. The low external magnetic field enables the isolator to tightly integrate into systems with high magnetic-field sensitivity such as atomic spectrometers, magnetometers, clocks, and cold-atom devices.
-
product
Polarity Tester
PT-1
International Electro-Magnetics, Inc.
The PT-1 provides a simple and easy way to determine the relative polarity of coil windings. It allows for an in-process test that takes a minimum of time to perform. By placing a coil on the platform and making connection to the start and end of a winding, a test signal is induced in the winding. The induced signal is low level and completely safe for the operator. By comparing the test signal phase of the coil under the test output, the relative polarity is indicated by the Red/Green LED. The tester operates by inducing a signal voltage in the coil under test by means of a magnetic flux field. The field is generated by a coil located in the probe base. The coil configuration is designed to provide optimum field distribution. We have also applied this basic circuit to a 5-channel scanning unit.
-
product
Digital Geological Data Collector
TECTRONIC
F. W. Breithaupt & Sohn GmbH & Co.KG
*Measurement and reading of azimuth of dip and angle of dip in one single operation (according to Clar method)*LCD display and memory for approx. 4.000 measurements*RS232 interface*Display indication 1° (360°, 400g, 6400– or 6300– selectable)*Many additional functions like measurement of magnetic field intensity)*Circular spirit level*Accessories upon request (Software, tripods, battery packs, …)
-
product
Magnet Testing
Helmholtz Coils
A coil arrangement consisting of two coils with the same radius or edge length is called a Helmholtz coil. At the correct distance, these coils are arranged in parallel on the same axis and current flows through them in the same direction. Their magnetic field is then characterized by a large homogeneous area in the center of the coil, which is freely accessible for experiments and measurement tasks. Helmholtz coils can have a circular or square geometric shape.
-
product
Magnetometers
The strength of magnetic fields can be determined with a magnetometer. Regardless of whether in the private sector or in the work environment, the increasing use of technology and networking also increases the exposure to magnetic and electromagnetic radiation. This radiation can have a negative effect on living beings, but also on sensitive electronic devices. Many effects are so unspecific that radiation is often not recognized as the cause. With a magnetometer you can measure how strong the radiation is at your sleeping place, in the kitchen in front of the microwave or induction stove or at your workplace. The location of sensitive electronic devices such as a precision balance can be examined with the magnetometer. The extent to which the radiation intensity increases or decreases with distance can be determined by positioning the magnetometer at various distances from the radiation source.
-
product
Handheld Digital Thickness Gauges
HC-210
Shenzhen Chuangxin Instruments Co., Ltd.
HC series of coating thickness gauge is a portable thickness gauge with eddy current thickness method and electromagnetic thickness method. It can be used to quickly and accurately measure the thickness of coating or cladding material without damaging it. As an essential instrument for professional material protection, this coating thickness gauge is widely used in manufacturing industry, metal processing industry, chemical industry and commodities inspection etc., both in the laboratory and in the engineering field. It can measure the thickness of nonmagnetic layer on magnetic metal substrate condition (such as steel, iron, alloy and hard magnetic steel, etc.) and the thickness of conductive layer on nonmagnetic metal substrate condition (such as rubber, paint, plastic, anodic oxidation film, etc.).
-
product
Digital Thickness Gauges Paint Gauge Meter
HC-200
Shenzhen Chuangxin Instruments Co., Ltd.
HC series of coating thickness gauge is a portable thickness gauge with eddy current thickness method and electromagnetic thickness method. It can be used to quickly and accurately measure the thickness of coating or cladding material without damaging it. As an essential instrument for professional material protection, this coating thickness gauge is widely used in manufacturing industry, metal processing industry, chemical industry and commodities inspection etc. ,both in the laboratory and in the engineering field. It can measure the thickness of nonmagnetic layer on magnetic metal substrate condition (such as steel, iron, alloy and hard magnetic steel, etc.) and the thickness of conductive layer on nonmagnetic metal substrate condition (such as rubber, paint, plastic, anodic oxidation film, etc.).
-
product
Digital Thickness Gauges Ultrasonic Coating Thickness Meter
HC-220
Shenzhen Chuangxin Instruments Co., Ltd.
HC series of coating thickness gauge is a portable thickness gauge with eddy current thickness method and electromagnetic thickness method. It can be used to quickly and accurately measure the thickness of coating or cladding material withoutdamaging it. As an essential instrument for professional material protection, this coating thickness gauge is widely used in manufacturing industry, metal processing industry, chemical industry and commodities inspection etc. ,both in the laboratory and in the engineering field. It can measure the thickness ofnonmagnetic layer on magnetic metal substrate condition (such as steel, iron, alloy and hard magnetic steel, etc.) and the thickness of conductive layer on nonmagnetic metal substrate condition (such as rubber, paint, plastic, anodic oxidation film, etc.).
-
product
Three-axis Hall Magnetometer
THM1176
The THM1176 family combines the performance of a professional Hall instrument with the usability of a consumer USB device. Its range goes from the µT to 14 T, DC to 1 kHz, with ±1% accuracy. It simultaneously measures all three axes of the magnetic field, so you get a true field strength reading no matter how you hold the probe. The entire instrument has been reduced to a cable with a few fat spots, which can plug directly into your PC or into a battery-powered handheld computer. The result is the most compact, lightweight, low-power, go-anywhere and measure-anything magnetometer in the world. Teslameter Gaussmeter 3-axis
-
product
Shield
Arduino MKR IMU Shield
The MKR IMU Shield is based on the BNO055 absolute orientation sensor from Bosch Sensortec GmbH which integrates a triaxial 14-bit accelerometer, a triaxial 16-bit gyroscope with a range of ±2000 degrees per second and a triaxial geomagnetic sensor with a 32-bit microcontroller running the BSX3.0 FusionLib software. The sensor features three-dimensional acceleration, yaw rate and magnetic field strength data each in 3 perpendicular axes.
-
product
Three Loop Antenna
VVLA-30M
The three loop antenna VVLA-30M is a standard measurement antenna according to CISPR15-2005/GB17743-2007 standard
, it can work with LISUN EMI-9KA / EMI- 9KB EMI Receiver System for EUT magnetic field radiation measurement between X, Y and Z planes. The antenna measurement is accurate, switch conveniently and it can completely replace imported products. -
product
Multi-Sensor
Panda
The NeuLog Panda multi-sensor can be used for any science experiment which utilizes Room Temperature, Light, Barometric pressure, Altitude, Sound, Relative Humidity, Dew-Point, Magnetic Field and G-Acceleration readings.Panda is used for environmental data collection and other experiments in Natural Science, Biology, Physics and Chemistry. It is specially designed for primary school level.The multi-sensor comes pre-calibrated so you can start experimentation right out of the box
-
product
Turbine Flow Meters
Axial turbine flow meters are designed with wear resistant internal components to provide trouble-free operation and a long service life. Fluid entering the flow meter is first conditioned by the inlet flow straightener which reduces turbulence in the fluid. The moving fluid causes the rotor to spin at a speed that is proportional to its flow rate. As the turbine blades on the rotor pass through the magnetic field of the pickup, an electronic pulse is generated.
-
product
Helmholtz Coils
A Helmholtz coil is actually a pair of specially constructed coils mounted a fixed distance apart on a common base. Current passed through the coils produces an extremely uniform magnetic field in the space between them. For the measurement of magnets, the coils are used in a different manner – they are connected to an integrating fluxmeter, which gives an accurate indication of the overall strength of the magnet when it is withdrawn or rotated a half-turn. If a gaussmeter is used for this purpose, many measurements may have to be made because of local variations of magnetic strength. A Helmholtz coil, on the other hand, measures the entire magnet at once, in a fast, reliable, and easy manner. For this reason, Helmholtz coils are ideal for quality checking of magnet parts after they have been magnetized.