Filter Results By:

Products

Applications

Manufacturers

Measurement

an acertained value.

See Also: Metrology, Instrumentation, Sensors, Meters, Stability


Showing results: 4876 - 4890 of 10608 items found.

  • Photo Detector Testing

    Enlitech

    With the rise of 5G technology and popularization mobile devices, more and more advanced photoelectric sensors are used in our daily lives. In order to be better applied to mobile devices, the photosensitive area of these advanced photodetector is getting smaller and smaller. However, these applications place higher and higher requirements on the light sensing performance of advanced photodetectors. In the process of shrinking the photosensitive area, it also brings the challenge of accurate measurement of quantum efficiency. Enlitech adopts the spatial light homogenizing technology and follows the ASTM standard “Irradiance Mode” test method, which is proven that it can accurately perform quantum efficiency and other key parameter measurements of advanced photodetectors.

  • 0.05° Accuracy Full Attitude Dynamic Motion Sensor

    DMS-05 - Teledyne Marine TSS

    The DMS range of motion sensors is designed specifically for the motion measurement needs of the marine industry. Whether it is achieving IHO standard survey from any size of vessel, or providing safety critical monitoring of offshore platforms, large vessels, helicopter landing decks, cranes and positioning systems, the DMS provides accurate motion measurement in all sea conditions. Incorporating an enhanced external velocity and heading aiding algorithm for improved accuracy during dynamic manoeuvres, the solid state angular rate sensors offer reliability in the highest performing vertical reference units ever produced by TSS.- Low power, cost-effective solution

  • Multi-Component Gas Analyzer

    VA-5000 / VA-5000WM Series - HORIBA, Ltd.

    The Multi-Component Gas Analyzer VA-5000 Series is an all-round analyzer that satisfies measurement needs as required for environmental monitoring, energy development support, quality controls, and continuous emission monitoring, etc. The VA-5000 Analyzer can be configured with up to 4 detector modules within a single case. Many combinations of detector modules with a wide selection of ranges allows this series of analyzers to be used for a variety of applications. The VS-5000 Sample Gas Conditioning Systems are designed to support the VA-5000 Analyzers by proving the optimal sample conditions for measurement. We also have wall mounted type analyzer (VA-5000WM) that enables to install in a limitted installation space.

  • Oven Data Logger

    215 - Elcometer Limited

    Memory stores up to 260,000 readingsIdeal for testing for powder or liquid coatings in batch or conveyor ovensVariable measurement interval, date, time, °C / °FHigh temperature resistant teflon coated probe cables are easy to clean after each runQuick display shows maximum temperature, Cure-Index figure and pass/fail for each probeMeasure up to 6 different temperatures at one timeIdeal in situations where powder coated thickness is inconsistentStart and stop logging at a pre-set temperatureLarge menu-driven display for easy operationPrint full colour report directly to any HP printerUSB data output to ElcoMaster® software and combine with other key inspection measurements

  • Elcometer MarSurf PS10 Surface Roughness Tester

    7062 - Elcometer Limited

    In protective coating applications there is a requirement to measure surface roughness. With 31 surface parameter settings available the Elcometer 7062 surface roughness tester can display all parameters that comply to National & International Standards.These values include peak-to-valley profile measurement in combination with an assessment of the frequency of peaks within the sample area.The Elcometer 7062 surface roughess tester is a light weight and portable measuring solution for the range of surface roughness measurements required for compliance to International Standards.The unit is also suitable for assessing surface roughness conditions in a wide range of general industrial applications; particularly where the sample is too large to bring to the laboratory.

  • Positive Displacement (PD) Meters

    AW Gear Meters

    Positive Displacement (PD) flow meters are volumetric flow measurement instruments ideal for low flow rates, highly viscous fluids, and measurement of flows involving starts and stops or pulsing. Positive displacement flow meters are similar in design to the gear pump. The principle of operation is reversed however; instead of the gears driving the fluid, the fluid drives the gears. A non-intrusive hall-effect sensor detects the movement of the gear and as each gear tooth passes the sensor, a square wave pulse is produced and a discrete volume of liquid is measured. The resulting pulse train is proportional to the actual flow rate and provides a highly accurate representation of the fluid flow.

  • Wood Moisture Meter - Integral Pins and Remote Hand-Press Probe

    Extech MO220 - Extech Instruments Corporation

    The MO220 is specifically designed for monitoring moisture in wood. Memory contains 8 wood groups with calibrations for approx. 170 species of wood. Measurements can be taken using the integral pin electrodes or the included heavy duty remote probe. Automatically temperature compensated (ATC) readings when used with the temperature probe. Built-in calibration check, replaceable measurement electrode pins, user settable Auto Power off (1 to 9 minutes) with disable, and Low battery indication. Complete with protective cap, temperature probe, heavy duty remote moisture probe, replacement pins, two AAA batteries, and soft case.

  • Frequency Counter Products

    53200 Series - Keysight Technologies

    The Keysight 53200 Series of 350 MHz universal and RF frequency counter/timers serve all of your frequency and time interval measurement needs. 3 available models offer resolution capabilities up to 12 digits/sec single-shot frequency resolution on a one second gate. Single-shot time interval measurements can be resolved down to 20 psec. All models in 53200 series offer new built-in analysis and graphing capabilities to maximize the insight and information you receive. Use the connectivity of your choice: LXI-C/Ethernet, USB, GPIB. Additionally, an optional battery is available to increase portability and maintain time base accuracy.

  • Infiniium Oscilloscopes

    Z‑Series - Keysight Technologies

    At the extremes of electrical and optical measurements, you need to make rise time measurements without being limited by scope bandwidth. You need to see your signal and not oscilloscope noise, and you need fast analysis and hardware acceleration. The Infiniium Z-Series delivers this and more with its RealEdge technology enabling 63 GHz of oscilloscope bandwidth and superior signal integrity. The Z-Series takes advantage of indium phosphide chip technology and custom thin film packaging to give you extremely low noise, low jitter, and high effective number of bits. These technologies allow you to see the true representation of your signal.

  • NI-9326, 6-Channel, 150 V, 128 kHz C Series Frequency Input Module

    786999-01 - NI

    6-Channel, 150 V, 128 kHz C Series Frequency Input Module - The NI-9326 is a channel-to-channel isolated frequency input module for CompactDAQ and CompactRIO systems. This module includes six differential input channels with a 0 Vrms to 150 Vrms input range. The NI-9326 also features configurable thresholds for connection to a variety of variable reluctance sensors, single channel encoders, and hall-effect sensors. You can use the included embedded counters to perform frequency measurements or edge-counting for tracking total counts on a periodic signal. Additionally, the NI-9326 supports configurable Butterworth filters to help you perform low-noise frequency measurements.

  • NI-9326, 6-Channel, 150 V, 128 kHz C Series Frequency Input Module

    786999-02 - NI

    6-Channel, 150 V, 128 kHz C Series Frequency Input Module - The NI-9326 is a channel-to-channel isolated frequency input module for CompactDAQ and CompactRIO systems. This module includes six differential input channels with a 0 Vrms to 150 Vrms input range. The NI-9326 also features configurable thresholds for connection to a variety of variable reluctance sensors, single channel encoders, and hall-effect sensors. You can use the included embedded counters to perform frequency measurements or edge-counting for tracking total counts on a periodic signal. Additionally, the NI-9326 supports configurable Butterworth filters to help you perform low-noise frequency measurements.

  • Balance Thermocouple Power Sensor, DC To 50 GHz

    N8487S - Keysight Technologies

    The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.

  • Balance Thermocouple Power Sensor, DC To 18 GHz

    N8481S - Keysight Technologies

    The Keysight N8480S Series Balance Thermocouple Power Sensors are intended to be used as measurement standards for RF power. They are suitable for use in a microcalorimeter-based primary measurement standard and as a secondary or reference measurement standard. The new balance thermocouple power sensors offer a broad frequency range DC up to 18/50 GHz, high maximum input power of +20dBm, fast measurement speed/settling time as well as ease of maintenance.

  • Chemiluminesce​nce NOX-NO2-NO Analyzer

    Model N200 - Teledyne Advanced Pollution Instrumentation

    The Model N200 uses the proven chemiluminescence detection principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of low-level Nitric Oxide (NO), Nitrogen Dioxide (NO2) and total Nitrogen Oxides (NOx) gases.

  • CO Hand Held Meter

    DHM1200 - ZOGLAB Microsystem Co., Ltd.

    NDIR (non-dispersive infrared) waveguide technology, 5 years working capacity CO measurement accuracy up to 40ppm~70ppm Key query operation, MAX / MIN / AVG value available White LED backlight for working in bad light condition

Get Help