Showing results: 6181 - 6195 of 10562 items found.
-
160B Opt. 5 & 320B Opt. 5 -
Data Proof
Data Proof’s Low Thermal Guarded Scanners are designed to improve accuracy in high resistance measurements. Unguarded, the Data Proof scanners have leakages of about 1.5 x 1012 Ω which can cause errors of a few tenths of a ppm when measuring 1 MΩ. Guarding reduces the errors allowing excellent accuracy up to the 1 GΩ level.
-
TPA-GFM -
High Power Pulse Instruments GmbH
*Electrically isolated probearm for GND needle contact or general purpose DC, twin-wire HBM or flexible pitch VF-TLP/TLP/HMM/HBM force/sense probing based on the HPPI GF-A flexible pitch setup.*Suitable to mount the GF-A ground fixture needle for flexible pitch measurements. In addition a cable (e.g. for HBM) can be directly connected to the contact pin.*High stability
-
Sensirion AG
With our long history of designing mass flow solutions for medical and industrial automation, Sensirion is your ideal partner to support you in the development of new products. Our mass flow meters ensure fast, accurate and economical measurements of gas flow over a wide dynamic range. They are extremly reliable and long-term stable and are free from zero-point drift.
-
5658 -
Abaco Systems Inc
ECM P/N 5658 provides eight channels of 16 bit current measurement in the 0 to 25 milli-amp range. Each channel allows independent common mode voltages from -100 volts to +100 volts. Current detection is accomplished with a precision 100 ohm current sense resistor, creating a voltage drop of 2V in the current loop at 20 milli-amps.
-
FISO Technologies Inc.
FISO’s catheters offer significant advantages over traditional solid-state catheters, while maintaining an excellent performance in signal integrity and frequency response. The other major benefits of FISO’s catheters include: (i) no side-facing sensor measurement artifacts, which are pretty common near vessel walls, and (ii) the ability to function within an MRI machine, or high EMI/RF environments.
-
Shanghai Baudcom Communication Device Co.,Ltd.
BD-POW-D02N Optical laser light source is a self-developed instrument, Which features advanced control technology , high output, ultra low-power operation. It can work at single wavelength, dual wavelength or three wavelength. It can export a variety of modulation frequency (CW, 270HZ, 1KHZ, 2KHZ). It is widely used in optical communication, optical measurement, optical fiber sensing, and so on.
-
TMO300 -
T&M Tools Limited Co
◇ 5.6-Inch outdoor-enhanced touchscreen, 7.4V/4.4Ah Lithium battery◇ Event Dead zone as lower as 1.5meter◇ Combined multi-dynamic range and wavelengths◇ Muti measurement mode, support Touching LCD and pressing keys◇ Warning function could prevent OTDR module from being damaged by optical signal in fiber◇ Realtime measuring function, convenient to monitor the splicing process
-
DTS Series -
High Voltage Inc.
The DTS Series provides repeatable and accurate measurements of the breakdown voltage of insulating oils used in electrical equipment. The DTS-60D & DTS-100D offer 60 kV AC and 100 kV AC output respectively. They include three user-selectable, automatic voltage rates-of-rise, and automatic voltage shutdown with the meter indicating the flashover voltage. Various test cells are available.
-
HF03 / LI19 -
Hukseflux Thermal Sensors B.V.
The HF03 is a heat flux sensor that can be used in mobile applications. It is combined with LI19, a high accuracy hand-held read-out unit that can be used both for mobile measurements and as an amplifier directly connected to a PC. The combination HF03 / LI19 is typically used to study heat flux levels around flares and fires, and to calibrate flare radiation monitors / flare heat flux sensors.
-
APQM-700 -
Amperis sl
*4 current inputs, physical current measurement on the neutral conductor.*Recording of up to 1100 parameters, including average, maximum, minimum and instantaneous values*Built-in heater, stable operation at low temperatures down to -20ºC.*Internal rechargeable battery, meter autonomy (min. 6 hours)*Ingress protection IP65, possibility of working in rain, snow and high humidity.
-
48265 -
Hickok Inc.
Accurate pressure measurements are more critical now than ever. Increase your diagnostic accuracy by viewing live pressure readings in Gauge (analog & digital) and Waveform formats all at once on your PC. It's like using an oscilloscope and gauge to look at dynamic pressures at the same time. Available in two models to fit your specific needs.
-
WIKA Alexander Wiegand SE & Co. KG
Process transmitters differentiate themselves from pressure sensors through their increased range of functionality: They feature integrated displays, offer high measurement accuracies and freely scalable measuring ranges, communicate via digital bus signals and can be delivered with a multitude of case variants. Through connection to diaphragm seals, WIKA process transmitters are also suitable for the harshest operating conditions.
-
2839-1V(D)-2842-1V(D) -
Georg Fischer Signet
The Signet 2839-1V(D) to 2842-1V(D) Conductivity/Resistivity Electrodes are available in four cell constants from 0.01 to 10.0 cm-1, and are suitable for a wide variety of applications from high purity water quality monitoring to weak acids and bases. 316 SS electrode surface finishes are controlled in a precision bead blasting operation to ensure measurement accuracy and repeatability.
-
ABET Technologies Inc.
Abet Technologies offers a range of standard EQE and IQE measurement systems. Model QE-1100 is configured with the most useful components for single junction devices. It has a 350 – 1100 nm range. The QE-1800 is configured with components most useful for components for triple junction cells. Beyond the standard systems offered systems can be custom configured to meet a customer’s metrology needs.
-
Arrival 3D, Inc.
The term “reverse engineering” can be a little confusing. It is sometimes used for things like software and electronic circuits. When 3D scanning companies use the term, they are referring to the process of re-creating design drawings by taking measurements and/or scans of the part itself. It is a 2-step process: 1) capture a 3D scan of the object, and 2) Create a 3D CAD model of the object