Filter Results By:

Products

Applications

Manufacturers

Measurement

an acertained value.

See Also: Metrology, Instrumentation, Sensors, Meters, Stability


Showing results: 8641 - 8655 of 10468 items found.

  • High Accuracy Spectrophotocolorimeter

    LMS-3000 - Lisun Electronics Inc.

    • Measure and display the relative spectral power distribution (UV-VIS-NIR) P(λ), chromaticity coordinate, correlated color temperature, rending index, color difference, peak wavelength, luminous flux, luminous flux efficiency and photometry parameters of light source and light material under the control of general PC. • Automatically adjust high-voltage, it not only shortens the measurement time, but also reduces the wear and tear of the instrument • Simultaneously measure the temperature in both environment and integrating sphere to make the data more visually and reliably • Figure of chroma and color difference in test report can be exchanged freely • Color display and print. The relative spectral power distribution (UV-VIS-NIR) P(λ), reports both in English. RS-232-C interface, compatible with all kinds of computer • LSP-500 AC Power source PC RS-232-C interface. compatible with all kinds of computer • Range of wavelength: 380nm~780nm(Special:200nm~780nm) • Accuracy of wavelength: ±0.2nm • Repeatability of wavelength: ±0.1nm • Accuracy of chromaticity coordinate: ±0.0003(under standard illuminate A) • Spectrum sample interval: 5nm(Special order:1nm) • Luminosity linearity: 0.3% • Accuracy of luminosity: 1 class • Correlated color temperature measure range: 1500K~25000K • Accuracy of CCT: ±0.3%(under standard illuminate A) • Accuracy of rending index: ±(0.3%rd±0.3) • Environment temperature measure range: -10℃~80℃ • Temperature measure range(In sphere): -10℃~100℃

  • 1000A AC Clamp Meter

    CM55 - Martindale Electric Co. Ltd

    The CM55 is a pocket sized high performance AC Clamp meter measuring AC current, AC/DC voltage and resistance with continuity test. The compact rugged design enables accurate and reliable current measurement down to 10mA resolution without the need to break into the circuit.The CM55 has a CATIII 600V safety rating and is the ideal tool for residential and commercial electricians.

  • Acoustic Test Chambers

    ViAcoustics

    Small Device Test Chambers are used for >Basic sound level measurement of small products and equipment >Pre-compliance testing of small products and equipment >End of line manufacturing test on small products and equipment Small Device Test Chambers provide acoustic isolation from outside sounds and/or reduce the sounds from the device under test radiating into the host

  • Laser Shearography NDT Sensor for Quality Control, Academic Research, or NDT Training

    FlawScout - Dantec Dynamics A/S

    The FlawScout is a laser shearography non-destructive testing (NDT) sensor designed to be used for (post-production) quality control, academic research, or NDT training. The sensor can be configured with thermal or vacuum (partial) excitation systems depending on the application. The FlawScout incorporates the very latest in phase-shifting technology delivering accurate and reliable measurement results through clear and sharp imaging with sub-micrometer displacement resolution.

  • 4 2/3 Digital Temperature (RTD) Meter

    CS2-T - Chuan Sheng Electronics Co., Ltd.

    CS2-T Temperature Indicator has been designed with high accuracy measurement, display and communication of Thermocouple or Pt100Ω.They are also building in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of machinery and testing equipments application.

  • Non-contact Io/Ior Leakage Clamp Meter

    M-340IRV - MULTI MEASURING INSTRUMENTS Co., Ltd.

    ・Safety by non-contact sensor, not touching live part directly (prevention of electric shock, short-circuit, etc.).・Easy to carry and operate, clamp CT + display part integrated type.・Measurable line current + leakage current + resistive leakage current by one unit.・Palm size mini clamp type.・High accurate measurement with min. resolution 0.001mA.

  • Coupler Metrology

    Rosenberger Hochfrequenztechnik GmbH & Co. KG

    Rosenberger provides directional coupler-based measurement techniques as well as probes for comprehensive cross-domain coupling analysis.Nowadays, the introduction of new accessories within vehicles, like rear seat infotainment, smart dashboards, and various advanced driver assistance systems, has increased the demand for high-speed automotive bus systems working in parallel with the high-voltage power networks in electric cars.

  • Battery Internal Resistance Tester

    FST-7000 - Foresight Electronics Co., Ltd.

    Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds. With the help of this device either single cells / blocks or large, multi group battery banks can be measured within a short time and the precisely measured data are processed and reported by given analyzer software automatically.

  • Fibre-Coaxial DOCSIS Analyzer

    CABLERANGER - PROMAX Electronica

    DOCSIS 3.0 analyzers for hybrid Fibre-Coaxial networks CABLE RANGER from PROMAX provide all the required measurements to install and carry the network maintenance of those hybrid networks using fiber optics and coaxial cables at the physical layer. The operating frequency range spans from 5 Mhz to 1700 Mhz, thus fulfilling DOCSIS 3.0 and 3.1 requirements.

  • PON Power Meter

    CARY-P100 - UC Instruments, Corp.

    The CARY-P100 PON Optical Power Meter was design for the FTTx application and maintenance which not only can be used to test and estimate the PON signals at the same time, but also the normal power measurement and fault identification. It is a useful, essential and ideal tool for the construction and maintenance of the PON projects.. Longlife battery power provides more than 8 hours outdoor test capability.

  • Coefficient Friction/Peel Tester

    32-76e - Testing Machines, Inc.

    32-76e coefficient of friction/peel tester uses advanced digital force signaling and high-speed data acquisition software to provide unmatched precision and repeatability in COF and peel testing. Improved features include a color touchscreen display and intuitive software user interface for easy navigation and test method storage. Peel testing capabilities include 180° peel and T-peel measurements.

  • Data Loggers

    IPETRONIK GmbH

    For fleet testing or endurance testing – IPETRONIK data loggers are employed worldwide within some of the most extreme, extended use environments, with technologies that offer unique capabilities for the effective measurement of drivetrain, engine cooling, in-vehicle climate control, HVAC systems and other challenging applications. Our loggers provide dependable data acquisition, also in hybrid and electric vehicles.

  • Portable RF Analyzer

    PMT-330 - Sensortech Systems, Inc.

    The Process Sensors Portable Moisture Tester (PMT-330) puts the capabilities of an on-line moisture analysis and control system into the palm of your hand, allowing operators to spot-check moisture content of boards, wood, plastic, and paper products quickly and easily. It features radio frequency dielectric (RF) measurement technology that penetrates the surface of products and instantly displays accurate moisture data.

  • Structural Load Monitoring

    SLM - Integrated Test + Measurement

    Since 2001 ITM has installed structural strain based monitoring systems in the pulp & paper and energy generation industries. For these systems, our engineers and field service technicians turn structures into measurement instruments (load cells). Load outputs from the structural load cells are monitored and published by a realtime controller to its local interface or network historians and HMIs.

  • Laboratory Centrifuges

    ACUTRONIC Switzerland Ltd

    Centrifuge systems are designed for the development, test, evaluation and calibration of accelerometers and a variety of inertial devices. Centrifuges provide a cost-effective solution for simulating high-"G" environments in the laboratory. They support testing of devices such as MEMS-based Inertial Measurement Units (IMUs), low-cost quartz or silicon sensors, Ring Laser Gyros (RLGs), Fiber-Optic Gyros (FOGs), fuzes and crash sensors.

Get Help