Showing results: 9301 - 9315 of 10458 items found.
-
TWA Standard Series -
Amperis sl
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
-
40-523-022 -
Pickering Interfaces Ltd.
Medium density PXI dual 44x4, 2-pole matrix - it is also available in reed relay formats of 1-pole and 1-pole screened (see "also in this range" on right). The screened version is suitable for switching signals up to 50MHz. Typical applications include signal routing in ATE and data acquisition systems. The two banks may be used for operating a 4-wire measurement system (bank-1 for source, bank-2 for measure). Larger matrices may be constructed by daisy chaining the common signals from multiple PXI Modules.
-
Mark-10 Corp.
Mark-10 digital force gauges can be used in a virtually limitless number of tension and compression force testing applications. All force gauges are able to capture the peak force in both tension and compression and have selectable units of measurement. Force gauge capacities are available from 50 gF full scale to 2,000 lbF, the broadest force range in the industry. Mark-10 force gauges may be handheld or used with a force test stand and gripping fixtures to create a complete testing solution.
-
Westboro Photonics
Westboro Photonics offers an intelligent selection of imaging photometers. With a wide range of resolutions, an assortment of lenses, flexible software, and cooled systems, our products are unmatched in the marketplace. We provide three series of photometers to satisfy almost any 2D luminance-based measurement need. Applications including Graphics Testing, Beam Pattern Distribution, Flat Panel Displays and Avionics Panel Balancing are handled with ease, thanks to our robust design, extensive calibrations, and flexible, intuitive analysis software.
-
VIS800 -
MicroImage Video Systems
Video Inspection Stations are available with?or without on-screen measurement capabilities?and offer?an excellent way to evaluate or test small works or items in?difficult to access locations.? As todays electronic and mechanical systems keep getting smaller, it becomes impossible to test or measure these products with traditional methods. For many applications, from development to production testing, video based inspection can help maintain quality control. Many of these systems are used in labs for development or used in production for testing production samples.
-
IT8500+ Series -
I-TECH Electronic Co., Ltd
IT8500+series (150W~3000W) single-channel programmable DC electronic loads are designed for middle & high-end applications.They can be offered as multiple solutions according to customer's design and testing requirements.The user can perform online voltage measurements and adjustments or simulate short circuit test using the simple keypad on the front panel. IT8500+ series DC loads are a versatile instrument for static and dynamic testing of power supplies,batteries,DC - DC converters,battery chargers,provides user the best testing solution.
-
FLIR A6700 MWIR -
Teledyne FLIR
Designed for electronics inspections, manufacturing monitoring, scientific research, and non-destructive testing, the FLIR A6700 MWIR camera is ideal for high-speed thermal events and fast-moving targets. Short exposure times allow users to freeze motion and achieve accurate temperature measurements. In fact, the camera’s image output can be windowed to increase frame rates to 480 frames per second to accurately characterize even higher speed thermal events, helping ensure critical data doesn’t get missed during testing.
-
VIS810 -
MicroImage Video Systems
Video Inspection Stations are available with?or without on-screen measurement capabilities?and offer?an excellent way to evaluate or test small works or items in?difficult to access locations.? As todays electronic and mechanical systems keep getting smaller, it becomes impossible to test or measure these products with traditional methods. For many applications, from development to production testing, video based inspection can help maintain quality control. Many of these systems are used in labs for development or used in production for testing production samples.
-
DX-201 -
Dexing Magnet Tech. Co., Ltd
DX-201 digital fluxmeter is a precise magnetic measuring instrument, adopted low drift electronic integrator design and production. The most important features are test response quick, without data lose in the testing process. In the process of test samples flux by the Czochralski method, fast pull and slow pull datas are consistent, fine features especially shows in repeated measurements and regression testing. It can measure magnetic flux or magnetic moment matched with different fixtures according to users’ requirements.
-
OP-SB85L -
LINEEYE Co., Ltd.
OP-SB85L is the interface expansion kit that has a port to measure TTL / CMOS signal level communications, and the one to measure the voltage of high-speed analog input. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communication between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI on monitoring and simulating.
-
MSP Corporation
TSI's Quest™ Edge Personal Noise Dosimeters are shoulder mounted, providing ergonomic, convenient measurement. Handheld Quest sound level meters measure average sound pressure level over time. All units are compact, with large displays and intuitive interfaces to provide crucial information at a glance and in real-time. Our personal noise indicators and sound detectors make it easier to measure sound and noise levels in real-time, and determine the level of hearing protection necessary in a particular environment.
-
KH23101 -
Beijing KeHuan Century EMC Technology Co,.LTD
The KH23101 current caliper is a toroidal transformer used to measure EMI current. When measuring, the caliper does not directly touch the electrical conductor or the cable under test. The conductor passing through the caliper window is used as the single-turn primary wire of the transformer, and the secondary is designed to be multi-turn. Use with 50 Ω receiving system (such as EMI electromagnetic interference field strength meter or spectrum analyzer). In order to facilitate installation and rapid measurement of EMI current, it is designed as a caliper that can be opened.
-
LabRAM Odyssey -
HORIBA, Ltd.
Special 50 years anniversary series: true confocal Raman microscope enabling the most detailed images and analyses to be obtained with speed and confidence. Ideally suited for both micro and macro measurements, it offers advanced confocal imaging capabilities in 2D and 3D. With guaranteed high performance and intuitive simplicity, the LabRAM Odyssey™ is the ultimate instrument for Raman spectroscopy, widely used for standard Raman analysis, PhotoLuminescence (PL), Tip Enhanced Raman Spectroscopy (TERS) and other hybrid methods.
-
LabRAM HR Evolution -
HORIBA, Ltd.
The LabRAM HR Evolution Raman microscopes are ideally suited for both micro and macro measurements, and offer advanced confocal imaging capabilities in 2D and 3D. The true confocal Raman microscope enables the most detailed images and analyses to be obtained with speed and confidence. With guaranteed high performance and intuitive simplicity, the LabRAM HR Evolution is the ultimate instrument for Raman spectroscopy. They are widely used for standard Raman analysis, PhotoLuminescence (PL), Tip Enhanced Raman Spectroscopy (TERS) and other hybrid methods.
-
RA2009D -
Radiasun International Group Ltd.
RA2009D comes with a solution that can handle digital TV and maintain the analog spectrum, enable technicians to use it in the most demanding situations with a single, rugged instrument, wherever it is needed. The new QAM View digital analysis option adds forward path digital signal testing that includes constellation, pre/post FEC BER, MER. Analog signal measurements are addressed with standard features like RF signal level, full scan, TILT, in-service C/N, A/V, and FCC compliant autotesting.
