Showing results: 9451 - 9465 of 10458 items found.
-
IST-6700 -
IST Information Scan Technology, Inc.
The IST 6700 is a low cost, stand-alone test instrument that provides a wide range of automatic and manual features for troubleshooting microprocessor-based circuit boards. It employs CPU emulation with low cost CPU personality pods to attach to or replace the resident CPU. With stored "Known Good" test data, the 6700 can provide fully automatic functional tests to check the system RAM, ROM, control signals, address, and data bus plus the measurement of the CPU clock frequency and supply voItage.
-
CRY6125 -
CRYSOUND
CRY6125 Electroacoustic tester is a full-featured electroacoustic device tester with resistance to environmental noises. It is designed to measure the performance indicators of microphones, electret microphones (MIC), transmitters, receivers, earphones, headset microphone assemblies, communication helmets, speakers/loudspeakers, buzzers and other electroacoustic devices, such as sensitivity (SPL), impedance, distortion (THD), resonance frequency F0, quality factor Q, equivalent volume, and audio power amplifier, etc. Its measurement frequency can be up to 10 Hz - 65 kHz.
-
E5007A -
Keysight Technologies
The E5007A provides the impedance analysis (ZA) firmware for the E5061B LF-RF network analyzer. This option enables the analyzer to measure impedance parameters of electronic components such as capacitors, inductors, and resonators. The combination of NA and ZA capabilities further enhances the analyzer’s versatility as a general R&D tool. Basic ZA functionalities including fixture compensation and equivalent circuit analysis are supported by the firmware. The DC biased impedance measurement is possible with the built-in DC bias source provided by the E5061B-3L3/3L4/3L51.
-
85039B -
Keysight Technologies
The Keysight 85039B calibration kit, with option M0F, contains male and female type-F open, short, and load standards. This calibration kit works with all 75 ohm network analyzers and test sets for measurement of devices with 75 ohm type-F connectors. The kit also includes type-N to type-F adapters. More economical versions of this kit are available by ordering option 00F for the female standards only, or option 00M for the male standards only. This kit is specified from dc to 3 GHz.
-
Keysight Technologies
The laser head is the source of the laser beam used in all laser motion and position measurement systems. The primary difference between laser heads is in the velocity, reference frequency and optical output power. Other considerations are size, heat dissipation, and input power requirements. Which laser you choose depends primarily on the application in which it will be used. For example, semiconductor lithography systems typically have faster moving parts (stages), and therefore need higher velocities than machine tool applications.
-
N5241B -
Keysight Technologies
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
SignalCore, Inc.
SignalCore offers traditional multi-stage and single-stage RF upconverters, and Direct IQ modulators that feature low phase noise, high dynamic range, wide bandwidth, and continuous tuning. SignalCore RF upconverters are compact and built for mechanical robustness and ruggedness. Applications include various test and measurement applications such as those in point-to-point radio, wireless communication, ATE, and software-defined radio. All products are provided with a Graphical User Interface (GUI), driver, and API for easy programming control.
-
SFB150 -
Shanghai Launch Electric Co., Ltd.
Zinc oxide arrester tester is specifically designed to detect internal electrical defects of power system with 10KV and below using MOA valve clearance indirect contact and to measure leakage current under MOA DC reference voltage (U1mA) and 0.75 U1mA. The instrument integrates high-voltage DC power supply, measurement and control system. All components are concentrated in a single chassis, with small size, light weight. It is a must for power system and zinc oxide arrester tester manufacturer field test.
-
Model KM 730 / KM 732 / KM 733 -
Kusam Electrical Industries Limited
IRthermo-Anemometer is with built-in non-contact Infrared Thermometer. The IRthermo-Anemometer is the air velocity, air flow (volume), air temperature, and non-contact infrared temperature measuring instrument. To measure the air velocity, put the sensor head face to the measurement air. Then the first reading will show the air velocity value. To measure a temperature, point the meter at a target until the temperature is read. (Make sure the target area is larger than the unit’s spot size. For large target object ensure that you are within target distance.)
-
85059V -
Keysight Technologies
The Keysight 85059V is a 1.0 mm verification kit designed for vector network analyzer systems operating over the frequency range of DC to 120 GHz. This includes a set of standards with known characteristics, traceable to primary standards in the Keysight Technologies calibration lab. This verification kit is used to verify the measurement calibration and also to verify that the PNA/PNA-X based millimeter-wave system is operating within its specifications. The 85059V with 85059B 1 mm calibration kit are replacements for the 85059A 1 mm calibration/verification kit.
-
HR8800 -
HighReach Measuring & Controlling System Co.,Ltd
The HR8800 water level recorder is a groundwater monitoring instrument with external power supply and internal battery self-power supply. It can be used for long-term recording of water depth (pressure) and temperature. It is all stainless steel structure. The recorder contains water level and temperature sensor, and the built-in large capacity is not easy. Loss memory and high-capacity long-life lithium battery, all functions are integrated in the instrument with a diameter of 24mm metal, suitable for water level measurement Of surface water, groundwater and marine environment.
-
Guided Wave
The optical or spectrum analyzer is the brain which transforms the signal collected by the sample interface into actionable information. Guided Wave sample interfaces (probes, flow cells) are designed for use with NIR or UV-Vis fiber optic coupled analyzers. They are designed to be rugged and reliable in harsh chemical and physical process conditions while providing optimal light transmission for long-term reliable measurements. More information is available about specific analyzers on each product page or on the process analyzer product overview.
-
OTP2 module no.187 -
LXinstruments GmbH
The PXIe‑4322 is a channel-isolated analog output module with built-in signal conditioning. The module provides accurate, simultaneous dynamic voltage and current outputs. By combining signal conditioning and D/A converters in one device, the PXIe‑4322 isolated analog output module offers smaller dimensions and higher measurement performance. In current mode, the module operates in all four quadrants, allowing current to be drawn and sourced. Thanks to isolation and outputs for higher voltages and currents, the module is particularly suitable for applications in the automotive sector.
-
OTP2 module no.193 -
LXinstruments GmbH
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions. PXI is both a powerful and cost-effective platform for applications such as manufacturing test, military, aerospace, machine monitoring, automotive, and industrial test.
-
2740 Family -
CAEN S.p.A.
The 2740 Digitizer is a 64-channel digital signal processor for radiation detectors available in VME64 (V2740), VME64X (VX2740), and Desktop (DT2740) form factor. It offers not only waveform digitization and recording but also Multi-Channel Analysis for nuclear spectroscopy using Silicon strip, segmented HPGe, Scintillation detector with PMTs, Wire Chambers, and others. The 2740 can perform pulse height measurements (PHA), constant fraction timing (CFD), charge integration (QDC) and pulse shape discrimination (PSD) independently for each of the 64 channels.
