Showing results: 76 - 90 of 218 items found.
-
3560 -
Abaco Systems Inc
ECM P/N 3560 provides four independent I2C channels. For ease of development a PCA9564 interface IC converts parallel data to I2C serial communication. Additionally an LTC1694 I2C accelerator IC decreases the rise time of the passively pulled up I2C bus allowing for greater capacitive loading or higher bus speeds. Each channel is comprised of SCL, SDA and two Grounds.
-
5041 -
Abaco Systems Inc
ECM P/N 5041 provides eight channels of RS485 / RS422 I/O with fixed 120 ohm termination for each channel. Speeds are up to 30M bits per second. All channels power up as inputs. Also transceiver inputs are always enabled for loop back diagnostic use when the outputs are enabled. Software can enable outputs on a channel by channel basis.
-
MMS6245 -
Abaco Systems Inc
The MMS6245 gives you the ultimate flexibility in rugged embedded I/O by allowing you to customize the 64 user-configurable front panel signals with our patented Electrical Conversion Module (ECM) technology. This configurable XMC carrier can host up to four ECMs giving you the ability to customize I/O to your specific needs.
-
5158 -
Abaco Systems Inc
The 5158 Electrical Conversion Module (ECM) provides eight (8) RS-232 outputs and eight (8) RS-232 inputs. Built around Maxim 1488 & 1489 chips for true RS232 levels and voltage tolerance, all outputs come up in the 1, mark or idle state. Electrically this is a negative output voltage, the start bit is always a 0 or a positive voltage level.
-
MMS8010 / MMS8011 -
Abaco Systems Inc
The Abaco ECM 3U VPX carrier supports up to six Abaco Systems Electrical Conversion Modules (ECMs) in a VITA 46 VPX form factor. Each ECM site connects 32 single-ended 3.3 V signals to the FPGA. The specific ECM board installed on a site converts the FPGA signals to 16 I/O signals, for a total of 96 I/O signals across the six ECM sites.
-
5658 -
Abaco Systems Inc
ECM P/N 5658 provides eight channels of 16 bit current measurement in the 0 to 25 milli-amp range. Each channel allows independent common mode voltages from -100 volts to +100 volts. Current detection is accomplished with a precision 100 ohm current sense resistor, creating a voltage drop of 2V in the current loop at 20 milli-amps.
-
3564 -
Abaco Systems Inc
The 3564 is a four channel comparator board with a common mode range of -150V to 150V on the two differential inputs and a DAC per channel to set trigger levels. The high common mode range and DC coupling provides a robust solution to level detection and triggering.
-
5047 -
Abaco Systems Inc
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
5147 -
Abaco Systems Inc
ECM P/N 5147 provides two channels of 12 bit A/D conversion using the Analog Devices AD9235, and is suitable for medium resolution high speed applications. The two differential inputs are terminated in 120 ohms and buffered with a gain of 1 differential amplifier. Differential Input range is +/-3.0V. Sample rates are 20MHz per channel with a 5MHz 4 pole elliptical analog input filter.
-
5093 -
Abaco Systems Inc
ECM P/N 5093 provides 2 independent full bridge circuits. The two full bridge circuits can be used together to drive one small two phase stepper motor. Each full bridge circuit can drive one small dc motor or other bipolar load. Note all inductive loads should employ transient protection.
-
5085 -
Abaco Systems Inc
ECM P/N 5085 provides two channels of 24 bit A/D conversion suitable for high resolution low speed applications, which include bridge circuits, thermocouples, RTD and voltage measurements. For bridge applications each channel provides a fused +5 Volt or a current source drive.
-
5081 -
Abaco Systems Inc
The 5081 provides four channels of 12 bit digital to analog voltage output, with multiple single ended output ranges. Each channel is software selectable for 0 to +5V, 0 to +10V, +/-2.5V, +/-5V, +/-10V or -2.5 to 7.5V ranges. The outputs reset to 0.0 volts on power up.
-
5089 -
Abaco Systems Inc
The 5089 provides eight channels of 12 bit A/D conversion using the Analog Devices AD7328, and is suitable for medium resolution medium speed applications.
-
7925 -
Chroma ATE Inc.
Chroma 7925 is an automatic inspection system for TO-CAN package. The appearance defects over 30 um like lens scratch, partial are clearly conspicuous by using advanced illumination technology. Because the height variation of tray and package exists, Chroma 7925 can calculate the focus distance and compensate to overcome the variation with auto focus function.
-
7940 -
Chroma ATE Inc.
Chroma 7940 wafer chip inspection system is an automated inspection system for postdiced wafer chip inspection.