Showing results 2311 - 2325 of 4381 products found.
-
IM2506 - Ajinkya Electronic Systems
IM2506 model which provides 6 digit display as compare to IM2501 Ampere Hour Meter which has 4 digit display. This model can be used with any circuit as the shunt value can be programmed by the user. The equipment is provided with one relay output to alert the user when the sufficient charge has been delivered. It is also used to directly cut off the rectifier.
-
F56 - Beijing Airport Beiguang Instruments Co., Ltd
F56 Metal Tube Float Flow meter Series are used for measure instantaneous and accumulated flow rate of liquid, gas and steam in closed pipelines. It is suitable for metering flow value on site or electronic remote. The measuring principle is based on the hydrodynamic effects,This makes float moving from bottom to top in vertical Pipe. As the displacement of float is in related to flow rate, which can be read from the indicator by means of the magnetic drive system in non-contact form . Also, flowmeters output electrical signal (4-20)mA / hart communication protocol with high / low limit Warning switches/integrating flow PCB broad can be configured.
-
Guangzhou GENY Electric Co.,
ingle Phase Electronic Energy Standard Meter Model ID: SZ-01A-K3E Features: High class accuracy up to 0.02% Wide testing range, 5V...480V in voltage, 1mA...120A in current Testing mode includes active powe, reactive power, cross connected reactive power Harmonic analysis.
-
Guangzhou GENY Electric Co.,
Three phase Stationary Reference Standard Model: QME4103 ◇ Description GENY's reference standard adopt unique sampling technology, with high accuracy, wide testing range. It is suit for electric power departments, electric energy meter manufacturers, measuring and quality.
-
SP79 - Martindale Electric Co. Ltd
The SP79 is a Class 2 sound level meter for on-site measurements in accordance with Noise at Work legislation in industrial and office environments. Featuring A and C frequency weighting and fast and slow time weighting, the compact design can be handheld, or mounted on a tripod for longer term monitoring of Min / Max values. Detailed recording and analysis can be made using the AC and DC outputs. The SP79 complies with BS EN 61672-1:2003 and is supplied with a detachable windshield and hard carry case. The large high contrast display includes both digital reading and analogue bar graph. An optional Class 2 sound level calibrator is available to verify accuracy before and after readings in accordance with international standards. The SPC70 is simple to use and provides a 1kHz reference at 94dB and 114dB.
-
B2987A - Keysight Technologies
The B2987A Electrometer/High Resistance Meter is the world's only graphical electrometer that allows you to confidently measure small currents with 0.01 fA (0.01 x 10-15 A) resolution and large resistances of up to 10 P (10 x 1015 ). In addition, battery operation eliminates AC line noise from your critical measurements. It possesses a 4.3" color LCD with a graphical user interface that provides trend chart and histogram data in addition to numeric information. These front-panel capabilities enable you to capture transient behavior and to perform quick statistical analyses without a PC. The available Setup Integrity Checker software option allows you to compare the noise levels of different cabling and fixturing arrangements to help isolate external noise sources.
-
ATRI-3 - UMA Electronics Enterprises
Range: 3.00 to 200.0 Accuracy : class 0.1 Ideal for tranformer and motor winding ratio measurement Auxilliary Power: 230V +/- 20% Measures and displays Transformer Turns Ratio by using voltage ratio method. Applying Test Voltage to the Low Voltage winding of a transformer and accurately measures the resulting voltage from the High Voltage winding. As per ANSI/IEEE C57.12.90 Standard Accessories: 10 meter long wire for three phase connection on LT and HT sides. Dimension: 131(H) by 280(W) by 230(depth) Excitation : 1.8V , 150.0Hz, sine wave. Max.500mA Fully Automated measurement of Turns Ratio, Excitation current, LT voltage, HT Voltage and polarity Three Phase Connection enables faster testing Test voltage is applied by 'PUSH to ON' switch, thus allowing safety of personnel during connection/disconnection (Optional) Data can be saved in memory card
-
SHANGHAI POWOO INDUSTRY
Technical specification of phantom load power sourcePower and consumption:Power supply: 1P2W 220V ±10%, 50Hz / 60Hz;Max consumption: 700VADimension: 500mm X 350mm X 650mmCurrent source:Output current: 3×0.001A - 3×100AAdjusting resolution: 0.01% (min. 0.0001A)Power factor: -1.0 ~ 1.0(0~3600; resolution: 0.10)Outputfrequency: 45Hz~65Hz;THD(sine wave output): <0.8%Stability of current during sine wave output:0.05% (180s)Output wave: sine waveOutput capacity: 150VA per phase Voltage source:Output voltage: 3×30V - 3×300VLoad: The Load could be resistor / inductive / capacitive(<4uF)Adjusting resolution: 0.01% (min. 0.1V)Outputfrequency: 45Hz~65Hz;THD (sine wave output): <0.8%Voltage stability of power source during sine wave output:0.05% (180s) Output wave: sine wave Output capacity: 15VA per meter position
-
Weschler Instruments
The Weschler Instruments BG "TC", TriColor BarGraphs provide the quickest way to spot problems in your process control panels with bright changing colors. Quick identification of trouble conditions can help prevent equipment damage or production loss, thus reducing down time and maintenance costs, and improving operational safety. Each 40 segment LED (Light Emitting Diode) of the BG TC family has the ability to illuminate as Red (Danger), Yellow (Caution), or Green (Safe condition). The bar color identification can be easily changed by the user, from the front pushbuttons or through a tamper safe mode. The fully programmable Weschler BG TC BarGraph™ fits the widest range of inputs and retrofits most edgewise switchboard and panel meters. Weschler's instruments satisfy the high quality standards set forth by the utility, OEM, and process control industries.
-
Nova ΙΙ 7Z01550 - Ophir Photonics
*Compatible with all standard Ophir Thermopile, BeamTrack, Pyroelectric and Photodiode sensors.*Large, high definition LCD display.*Both digital and analog needle display.
-
HW-3211 - Shanghai Fibretool Technology Co.,Ltd.
Reference power level storage(Ref setting) - User self-calibration function - Comfortable LCD display and backlight LCD display supports night operation - Power measurements in dBm or mw and insertion loss in dB Optional 10 minutes Auto-off function
-
Multigauge 5600 - Tritex
On screen user information such as probe frequency and remaining battery. Colour LCD display. Easy to use keypad and menu system.
-
NukAlert-ER - KI4U, Inc.
The NukAlert-ER™, with its unique 'Extended Range' Continuous Coverage from 1µR/hr through 600R/hr, performs all of the functions of the three devices that constituted our now lapsed Civil Defense Program.
-
MRC ltd.
Tests swimming pools, municipal water, food and beverage water, or other aqueous solution where fluid clarity is important.
-
11QE25-LP-S-MB - Standa
11QE25-LP-S-MB energy detector provides a unique combination of high damage resistance and high speed. It also offers very good linearity with power and a versatile mounting system. It is right for many pulsed lasers. It is right for many OEM, manufacturing and laboratory uses.